flash/stm32l4x: support STM32C0x devices

this new STM32 series family introduces 2 devices:
STM32C011xx (0x443) and STM32C031xx (0x453)

both devices have 32 Kbytes single flash bank.

Change-Id: I4e890789e44e3b174c0e9c0e1068383ecdbb865f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6874
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>

tcl/target/stm32c0x.cfg

@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# script for stm32c0x family
+#
+# stm32c0 devices support SWD transports only.
+#
+
+source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
+
+if { [info exists CHIPNAME] } {
+	set _CHIPNAME $CHIPNAME
+} else {
+	set _CHIPNAME stm32c0x
+}
+
+set _ENDIAN little
+
+# Work-area is a space in RAM used for flash programming
+# By default use 6kB
+if { [info exists WORKAREASIZE] } {
+   set _WORKAREASIZE $WORKAREASIZE
+} else {
+   set _WORKAREASIZE 0x1800
+}
+
+#jtag scan chain
+if { [info exists CPUTAPID] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   # SWD IDCODE (single drop, arm)
+   set _CPUTAPID 0x0bc11477
+}
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp   stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
+
+# reasonable default
+adapter speed 2000
+
+adapter srst delay 100
+if {[using_jtag]} {
+	jtag_ntrst_delay 100
+}
+
+reset_config srst_nogate
+
+if {![using_hla]} {
+	# if srst is not fitted use SYSRESETREQ to
+	# perform a soft reset
+	cortex_m reset_config sysresetreq
+}
+
+$_TARGETNAME configure -event examine-end {
+	# Enable DBGMCU clock
+	# RCC_APB1ENR |= DBGMCUEN
+	mmw 0x4002103C 0x08000000 0
+
+	# Enable debug during low power modes (uses more power)
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
+	mmw 0x40015804 0x00000006 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_WDGLS_STOP | DBG_WWDG_STOP
+	mmw 0x40015808 0x00001800 0
+}