Add common LPC2xxx setup procedure, use in all LPC2xxx files.

Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>

tcl/target/lpc2148.cfg

@@ -1,45 +1,9 @@
-# Proc that can be invoked to create a special version of
-# the LPC2148
-proc setup_lpc2148 {chipname tapids} {
-	# Use RCLK. If RCLK is not available fall back to 500kHz.
-	#
-	# Depending on cabling you might be able to eek this up to 2000kHz.
-	jtag_rclk 500
-	
-	adapter_nsrst_delay 200
-	jtag_ntrst_delay 200
-	
-	# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate
-	# JTAG, power-on reset is not enough, i.e. you need to perform a
-	# reset before being able to talk to the LPC2148, attach is not possible.
-	reset_config trst_and_srst
-	
-	eval "jtag newtap $chipname cpu -irlen 4 -ircapture 0x1 -irmask 0xf $tapids"
-	
-	target create $chipname.cpu arm7tdmi -chain-position $chipname.cpu
-	
-	$chipname.cpu configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
-	
-	$chipname.cpu configure -event reset-init {
-		# Force target into ARM state
-		arm core_state arm
-	
-		# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
-		# "User Flash Mode" where interrupt vectors are _not_ remapped,
-		# and reside in flash instead).
-		#
-		# See section 7.1 on page 32 ("Memory Mapping control register") in
-		# "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006.
-		# http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf
-		mwb 0xE01FC040 0x01
-	}
-	
-	# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
-	flash bank $chipname.flash lpc2000 0x0 0x7d000 0 0 $chipname.cpu lpc2000_v2 14765 calc_checksum
-}
+# NXP LPC2148 ARM7TDMI-S with 512kB flash (12kB used by bootloader) and 40kB SRAM (8kB for USB DMA), clocked with 12MHz crystal
 
+source [find target/lpc2xxx.cfg]
 
-# Default settings
 proc init_targets {} {
-	setup_lpc2148 lpc2148 "-expected-id 0x3f0f0f0f -expected-id 0x4f1f0f0f"
+	# 500kB flash and 32kB SRAM, clocked with 12MHz crystal
+	# setup_lpc2xxx <chip_name> <cputapid> <flash_size> <flash_variant> <workarea_size> <core_freq_khz> <adapter_freq_khz>
+	setup_lpc2xxx lpc2148 "0x3f0f0f0f 0x4f1f0f0f" 0x7d000 lpc2000_v2 0x8000 12000 1500
 }