The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Until this time only basic SLC functionality exists when you want to use SLC to access external nand flash.
Basic functionality can be selected with command:
lpc3180 select 0 slc
It is anyway very slow to write/read to/from nand flash.
With the new command, SLC speed improved about 20 times, and hardware ECC info also read/written from/to nand flash OOB area:
lpc3180 select 0 slc bulk
Speed improvement achieved by using working are in SRAM of the LPC3250 chip and controlling DMA controller to interact between SRAM and SLC peripheral.
Here are the patches, and if they are ok than take them.
Tested with hitex LPC3250 usb stick.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The LPC3180 NAND driver was crashing on some large page chips.
Fix:
- Crash and related functionality (don't memset too much OOB data)
- Some debug messages
- Command handling now works
[dbrownell@users.sourceforge.net: whitespace/linelength/message cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Refactored the write page raw function into two new functions
for writing data to a NAND device and then another function to
finish up a write to a NAND device. This includes some new
updates to introduce more error checking to existing code.
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Added a new function to encapsulate reading a page of data from
a NAND device using either the read_block_data function of a NAND
controller or to use direct reading of data from the NAND device.
This also adds some performance enhancements and uses the read_data
function if the read_block_data function fails safely (because it
can't allocate a buffer in the working area).
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move most declarations in <target/armv4_5.h> to <target/arm.h>
and update users.
What's left in the older file is stuff that I think should be
removed ... the old register cache access stuff, which makes it
awkward to support microcontroller profile (Cortex-M) cores.
The armv4_5_run_algorithm() declaration was moved too, even
though it's not yet as generic as it probably ought to be.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename nand.h as flash/nand/core.h, chase consumers. The public APIs
need to be sorted out with imp.h, but this allows other changes to
begin improving the separation between policy and mechanism.
Moves #include <target/target.h> and #include "driver.h" into the
internal headers or source files, removing it from <flash/nand/core.h>.
Moves commands into nand/tcl.c and core implementation to 'nand/core.c'
and 'nand/fileio.c'. Eliminates 'flash/nand.c'.
Adds 'nand/imp.h' to share routines between TCL commands and core.
This work parallels the NOR directory, encapsulating the NAND drivers
into a separate file. This takes an extra step by encapsulating the
type of data structure used to manage the drivers, allowing it to be
changed from an array to a dynamic list in the future.
Modify the arm_nand_data struct to better support both read and
write operations while using the same struct. An additional
field was added, and initialized, to record the last operation
so that the correct code can be loaded to the working area.
[dbrownell@users.sourceforge.net: merge init patch, tweak GPL note]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Before we can -I the top-level src/ directory alone, references to
"hello.h" must be updated. This is an internal header, so it does
not need angle brackets.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "s3c24xx_regs.h"
the following form should be used.
#include <flash/nand/s3c24xx_regs.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "nand.h"
the following form should be used.
#include <flash/nand.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "arm_nandio.h"
the following form should be used.
#include <flash/arm_nandio.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "armv4_5.h"
the following form should be used.
#include <target/armv4_5.h>
The exception is from .c files in the same directory.
Includes the src directory in the search path, so header files may be
migrated from:
#include "foo.h"
to
#include <module/foo.h>
which is more conducive for installation.
