Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
Use it whenever an out-of-sync response is detected to clean
USB bulk transfer state.
USB hidapi does not offer any means to cancel a pending request,
therefore cmsis_dap_hid_cancel_all() does nothing.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie36fa760c1643ae10be0e87fc633068965a72242
Reviewed-on: https://review.openocd.org/c/openocd/+/7366
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
The synchronous libusb_bulk_transfer() always waits
for the transfer to complete. Therefore it does not allow issuing
multiple USB requests as used on HID backend.
Switch to asynchrounous libusb_submit_transfer().
With this patch a good USB FS based CMSIS-DAPv2 adapter
almost doubles the throughput:
adapter speed: 20000 kHz
poll off
> load_image /run/user/1000/ram256k.bin 0x20000000
262144 bytes written at address 0x20000000
downloaded 262144 bytes in 0.428576s (597.327 KiB/s)
> dump_image /dev/null 0x20000000 0x40000
dumped 262144 bytes in 0.572875s (446.869 KiB/s)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ic6168ea4eca4f6bd1d8ad541a07a8d70427cc509
Reviewed-on: https://review.openocd.org/c/openocd/+/7365
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When user requested a change on cp0 status register,
it may contain changes on EXL/ERL bits, and changes on
these bits could lead to differnt behaviours on writing
to other cp0 registers.
Change-Id: Ic83039988c29c06ee134226b52de943c46d19da2
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7914
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Instead of returning an 'error string', throw an error. This makes it
much easier to handle errors in Tcl scripts or in tools that use Tcl RPC.
Change-Id: I75c48750cfad7430fa5e6bc88fe04ebd59d34cea
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8006
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I990c0f7a0871f4b1a0fcdd13afc190149302443c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8003
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Id32440cdd531077008abd679add32246c4249eb2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8001
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Idf3d7a46ddecd70823e06bc3997f41fcdb8e501f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8000
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I676e2ebf5714c850a436854a32c2e9d2f181d537
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7999
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, remove the syntax error messages as the correct
syntax is already suggested due to the return value used.
Change-Id: I9310ba96ed3f8a85c37cee9193e481ad3df02e77
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7969
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mips opcode macro for the SRL opcode was using the wrong constant
value:
SRA -- Shift right arithmetic
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0011
SRL -- Shift right logical
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0010
This corrects the opcode constant for SRL and adds the SRA opcode for
completeness.
There is only one user of MIPS32_OP_SRL in src/flash/nor/cfi.c:
Since the mask constant (0x00000080 for the DQ7 mask) shifted in this
case would never have the sign bit set, it worked fine even though it
was accidentally using the SRA opcode instead of SRL.
Change-Id: I0a80746e2075c7df1ce35b9db00d9d0b997a3feb
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/3613
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We were previously inadvertently clearing the top 32 bits of SCTLR_EL1
during read_memory/write_memory as a result of using 32-bit operations
to access the register and because the fields used to temporarily
store the register were 32-bit. Fix it.
Change-Id: I657d7f949e1f7ab6bf90609e3f91cae09cade31a
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7939
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Associativity=0 means that only one CMO is needed for all ways.
It could also mean that the cache is 1-way, but this is less likely.
Currently Associativity=0 causes us to hang in the while loop in
decode_cache_reg. Fix it by skipping the loop in this case. We can let
way_shift be set to the arbitrary value of 0 because in the case where
Associativity=0 we only ever shift 0 by it before ORing it into the
CMO operand.
Change-Id: I7c1de68d33f6b3ed627cbb1e2401d43185e4c1e3
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7916
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In the unusual (and even incorrect) case of running the command
target create ...
before defining an adapter and the associated transport, the
command causes a segmentation fault. E.g.:
openocd -c 'target create cpu cortex-m -endian little'
Check that get_current_transport() returns a valid pointer before
referencing it.
Change-Id: I9796a7e92196ef3df5c7152b27c34102045dc9e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7962
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
I use a script to compare the commands in the code with the ones
in the documentation.
Fix the style of the data to simplify the parsing.
Change-Id: I0f1d7e9ff5e2928312ca1a2f3424f82d2910580a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7960
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Enhance `mips32_read_config_regs` to better detect MIPS32 ISA,
DSP, and FPU features, allowing user to get more detailed
target information.
Most of these information will be used in MIPS m/iAptiv support.
Change-Id: I23571a626ec64fa019acac91bdbfcb434373bfc1
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7911
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This patch forces a read of register from the target
in the get_reg command in case the register cache
does not hold a valid value at that moment.
Note that the command "reg" already handles it
correctly, no fix is needed there.
Change-Id: I75fad25188e94ee4e06162ab6d600ea24dbf590a
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7958
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The original documents from Jedec since JEP106BG, do not report
the entry for "21 NXP (Philips)", replaced by "c".
It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I273c8c5ecf48336ce5189b484a7236273ba90184
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7954
Tested-by: jenkins
Previously, when listing the watchpoints, OpenOCD printed
numbers 0, 1 and 2 representing READ, WRITE and ACCESS type
watchpoints.
This patch changes it to 'r', 'w' and 'a'. This increases the
clarity as what type the watchpoint actually is.
Change-Id: I9eac72dfd0bb2a9596a5b0c080a3f584556ed599
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7909
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
