Move the ti targets to a TI folder. Since the folder is ti, we can
drop the "ti" prefix from the files themselves.
Done via the following script:
mkdir target/ti
FILES=`ls target/ti*.cfg target/omap*.cfg target/am335x.cfg
target/amdm37x.cfg target/icepick.cfg target/stellaris.cfg
target/davinci.cfg`
for cname in $FILES
do
bname=`basename $cname`
nname=`echo $bname|sed -e "s/^ti-//g"|sed -e "s/ti_//g"`
npath="target/ti/$nname"
echo "$cname => $npath"
fref=`git grep $cname .|cut -d ':' -f1|sort -u`
sed -i -e "s&$cname&$npath&g" $fref
git mv $cname $npath
done
Change-Id: I9f94dc6bb01f73721d4ff96be92cb51de2cbf0e2
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/9203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/board | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ibcf7da62e842aafd036a78db9ea2b9f11f79af16
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7028
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The Linksys WAG200G router has a TI AR7 SoC and a 4MB Flash layout
similar to the Netgear DG834v3 router [1].
Below is an example of a successful flash recovery, using a TUMPA,
connected to the MIPS EJTAG 2.6 header (JP102) of the router.
WAG200G [2] TUMPA [3]
Desc Pin Pin Desc
------------------------
nTRST 1 3 nTRST
TDI 3 5 TDI
TDO 5 13 TDO
TMS 7 7 TMS
TCK 9 9 TCK
nSRST 11 15 RST
GND 2 4 GND
Note that nSRST is optional to halt the CPU, but is required to probe
the flash. For instance, recover the kernel with:
$ sudo ./src/openocd -s tcl \
-f interface/ftdi/tumpa.cfg \
-f tools/firmware-recovery.tcl \
-c 'board linksys-wag200g;
reset_config srst_only;
flash_part kernel /path/to/kernel.bin;
shutdown'
[1] https://wiki.openwrt.org/toh/linksys/wag200g
[2] https://www.linux-mips.org/wiki/JTAG#JTAG_headers
[3] http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual#20_PIN_JTAG_Connector
Change-Id: I952ba9f706e2e4f8f95ca03a5fa58f391ca030b6
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-on: http://openocd.zylin.com/3776
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
