For stm32l4, stm32wbx, stm32wlx the target tcl scripts try to change the
MSI oscillator's speed to 24 MHz before boosting the interface
frequency, but don't clear the RCC_CR_MSIRANGE field correctly before.
This causes the register write access to fail and leaves the clock
frequency unchanged. For the stm32wlx, the script also neglects to set
the MSIRGSEL bit, such that the frequency setting is not actually
applied.
The issue appears to not cause a problem when using an ST-Link adapter.
When using an FT4232HP, communication to the target fails after the
reset-init event, possibly because this adapter actually supports the
higher interface frequency.
This commit fixes the register accesses to make sure the RCC_CR_MSIRANGE
is cleared to zero before OR-ing the new value. For the stm32wlx, also
set the MSIRGSEL bit. Just to be safe, also fix the write access to the
FLASH_ACR_LATENCY field to clear it before OR-ing, even though it should
be zero at reset anyways.
Change-Id: Ie8320fa6ee2086981c0b1f3c18f51e171709078d
Signed-off-by: Niklas Gürtler <profclonk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/9282
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
With commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu
code") the target's event "trace-config" has been deprecated.
Create the TPIU device.
Replace the target's event "trace-config" with tpiu's event
"pre-enable" in the STM32 devices that require enabling the trace
clock _before_ programming the TPIU.
Make the script multi-instance-able in case it's used for JTAG
chained devices.
Uniform the code in STM32F4x with the other scripts.
Remove the empty event from STM32WLx.
Change-Id: Ifda219c3c5f37e03072a88168611cf505eb630b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
