Based on the lpc3180 driver, but released as a separate driver for two reasons:
1) I don't have an lpc3180 to test it against, so it might unintentionally break compatibility.
2) It's using a different OOB layout than lpc3180.
Rewritten so that it no longer borrows code from the NXP CDL library. Instead borrowing code from the u-boot port to lpc32xx, written by Kevin Wells.
Tested on lpc3250 (Hitex LPC3250-Stick). OOB layout is compatible with LPCLinux.
Remove extra \n from LOG_DEBUG, LOG_INFO, and LOG_WARNING messages
Remove LOG_INFO_N
LOG_INFO_N was only used once and had a \n at the end
Change LOG_USER_N calls that end with \n to LOG_USER
Every NAND driver keeps private copy of "target"
structure.
Prepare infostructure to move private "target"
copy in common/shared struct nand_device.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Table of NAND devices reports operating voltage.
Replace comma with proper decimal dot.
Øyvind: "." is correct for UK/US, but incorrect for
many other languages. OpenOCD is not localized at this
point, so sticking to "." for US/UK should be OK.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
From struct nand_flash_controller :
- remove unused field register_commands;
- remove field controller_ready, exported but
never referenced.
Remove dead code pointed by controller_ready.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because
the read assumed a valid data buffer, which check_bad_blocks does not use
(it only passes a 6 byte buffer for the start of OOB).
This version copes with undersized or missing data or oob buffers and uses
random read commands within the page to skip unwanted areas of data/OOB for
speed.
NOTE: Running check_bad_blocks with this layout will be reading infix
OOB locations, not manufacturer bad block markers. This means that if you
check blocks written in infix layout they will appear good, but manufacturer-
marked bad blocks may also appear good.
If you want to scan for manufactuer-marked bad blocks, you need to enable
raw_access before running check_bad_blocks, or use the non-infix layout.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
CC: David Brownell <dbrownell@users.sourceforge.net>
nand_build_bbt() was ignoring the return value from nand_read_page() and
blindly continuing.
It now passes the return value up to the caller if the read fails.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Last block was being skipped, fix by changing the loop test from "<" to "<="
First block argument was ignored, always started from block 0 (and counted
the wrong blocks as bad if first was nonzero). Now we use it.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Until this time only basic SLC functionality exists when you want to use SLC to access external nand flash.
Basic functionality can be selected with command:
lpc3180 select 0 slc
It is anyway very slow to write/read to/from nand flash.
With the new command, SLC speed improved about 20 times, and hardware ECC info also read/written from/to nand flash OOB area:
lpc3180 select 0 slc bulk
Speed improvement achieved by using working are in SRAM of the LPC3250 chip and controlling DMA controller to interact between SRAM and SLC peripheral.
Here are the patches, and if they are ok than take them.
Tested with hitex LPC3250 usb stick.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The LPC3180 NAND driver was crashing on some large page chips.
Fix:
- Crash and related functionality (don't memset too much OOB data)
- Some debug messages
- Command handling now works
[dbrownell@users.sourceforge.net: whitespace/linelength/message cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Refactored the write page raw function into two new functions
for writing data to a NAND device and then another function to
finish up a write to a NAND device. This includes some new
updates to introduce more error checking to existing code.
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
SimonQian