To achieve that we need to avoid using FLASH_REG_BASE_B0, and use
bank registers instead:
For dual bank devices, each option register is mapped in 2 addresses
at the same offset from flash_bank_reg_base.
This is true for OPTCR, OPTKEYR, OPTSR_CUR/PRG, OPTCCR according to
RM0433 Rev6 (refer to section 3.9: FLASH registers)
In stm32x_write_options, according to RM0433 Rev6, after OBL launch we
should wait for OPTSR_CUR.BSY bit instead of FLASH_SR.QW
Change-Id: Ie24a91f069d03c9233797390fc2e925c737dad90
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5291
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Each bank had to store its options only, there is no need for bank1
to sneak into bank2 options.
Furthermore, some variants do not have a second bank.
Change-Id: I9229eb8ab4b5860ba2b0c5dbe626a54a84bca4d6
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5290
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Drop static pointer to allocated struct nrf5_info, iterate over
the flash bank list to find previously allocated nrf5 instances.
nrf5 is swd only device, so static allocation makes no harm,
but we should avoid copying the wrong code to other flash drivers.
Free sector array before allocating it to avoid memory leak on
re-probing device.
Change-Id: I781d8f4418a91c043f2393e5ecc5278fc6df3566
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4910
Tested-by: jenkins
Also refuse 'flash protect' on any nRF52.
Fail protection check on nRF52840 until ACL protection is implemented.
Change-Id: I84fcf117427e4894147c3ad92e2a3597566b4fcf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4864
Tested-by: jenkins
nrf5 flash driver detected devices by looking up the HWID in the table
of known devices. Unfortunately chips are produced with many different
HWIDs for each type.
All nRF52 devices have FICR INFO field suitable for device identification
without need of HWID lookup.
Some newer nRF51 devices have FICR INFO too although undocumented.
Use this information to identify the device.
nrf5_info() is reworked to show just concise info.
Decoding FICR and UICR registers was moved from nrf5_info()
to a new command 'nrf5 info' without functional changes.
The flash bank for UICR page has the same size as program flash sector.
Change-Id: I900095b9ae23ee995f8e2bef8539b75d00300da5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4848
Tested-by: jenkins
nRF5 flash controller can write a word at a time. Ask flash
infrastructure to handle alignment and padding.
Fix mixing of offset and address in nrf5_ll_flash_write()
- the original code worked just because NRF5_FLASH_BASE is 0
Change-Id: Ibe8bdf899a1764cf4117b2deda1a4618eeb16697
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4819
Tested-by: jenkins
Make driver_priv point directly into the corresponding chip bank structure
and add a pointer to it to get back to its chip when it's needed. This
removes the need to keep track of any bank number, either global or chip-
local.
In addition, it simplifies the cases where the chip structure was just used
to access the chip bank fields; now they are directly accessible.
Change-Id: Iaa353cd4fa7d8ff94c2ef69028c7cb32fade0420
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/4775
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The preverify option allows to check whether flashing is necessary.
If the target is flashed often/automatically this can save time and
preserve the flash. This is expecially helpful in CI environments.
Change-Id: Iead0a269e1a772b751d4dd9e8b53b2fecc874624
Signed-off-by: Moritz 'Morty' Strübe <moritz.struebe@redheads.de>
Reviewed-on: http://openocd.zylin.com/5292
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
According to the reference manual it should be 0x40000000. Flashing (and
booting) a firmware with this MSC base was successful.
Change-Id: I739e67d36555b8170a3b8e26f54cf1c09ce8424b
Signed-off-by: Christian Meusel <christian.meusel@posteo.de>
Reviewed-on: http://openocd.zylin.com/5263
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PAGE_SIZE is defined in system includes on some systems, this would
avoid the unintended conflict
Fixes
| src/flash/nor/esirisc_flash.c:95:9: error: 'PAGE_SIZE' macro redefined [-Werror,-Wmacro-redefined]
| #define PAGE_SIZE 4096
| ^
| /mnt/a/yoe/build/tmp/work/core2-64-yoe-linux-musl/openocd/0.10+gitrAUTOINC+7ee618692f-r0/recipe-sysroot/usr/inclu
de/limits.h:89:9: note: previous definition is here
| #define PAGE_SIZE PAGESIZE
Change-Id: I195b303fc88a7c848ca4e55fd6ba893796df55cc
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Reviewed-on: http://openocd.zylin.com/5180
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is no sense in displaying the max size (2M) as there is variants
of this device with reduced flash size
Change-Id: I40574064d75fdf2a038044c81038a6d7abc6c4dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5288
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Fix two expressions where precedence of operator | vs ?: was clearly confused.
Untested - was clearly not expressing the intent of the author by inspection.
Found by automated tooling and rtrieu@google.com.
Change-Id: I46f190154797f8affc761caf3a15a1a9db53d702
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/5281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is causing repeated build failures. Its design is so fundamentally
broken that if someone actually wants to use it, a full rewrite is the
only option. So it's not even worth deprecating in the hope that someone
will notice and fix it, just get rid of it.
Change-Id: I513069919a3873bd69253110f7fb6f622ee7d061
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5243
Tested-by: jenkins
Reviewed-by: Jeffrey Booher-Kaeding <Jeff.Booher-Kaeding@arm.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command uses LOG_USER() instead of command_print().
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92e5e5954a75b96093b3ed6af73a7536c063b639
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5083
Tested-by: jenkins
After replace CMD_CTX with CMD, the indentation is incorrect.
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5d7c40227ceda2e9db8dab88088d74012d2254c4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5082
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam4() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8dfa66f3f6be318d6ba89649279b1b4502f375d9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5055
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam3() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia1e7af79d0fc89d229b4e10df37317a374bbab62
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5054
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Pass CMD instead of CMD_CTX as parameter to nand_list_walker().
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia11887dfc6dc58d5458a88ba84780cd895b8c253
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5053
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of nand_fileio_start() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7993f6aba997a2d2917949563651c8d0c213730d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5052
Tested-by: jenkins
Based on RM0433.rev5 > Section 3.3.9 : Flash program operations:
QW1/2: this bit indicates that a write, erase or option byte change
operation is pending in the write queue or command queue buffer.
It remains high until the write operation is complete.
It supersedes the BSY1/2 status bit.
On this basis, stm32x_wait_status_busy is renamed accordingly to be
'stm32x_wait_flash_op_queue'
Note : In this commit there is a fix of SR_ERROR_MASK value in flash loader algo
Note : This modification is mandatory for revision X, and backward compatible
with old revisions
Change-Id: I59d2973317d76b01fbb0fb5e4a472a47d0a7a5b5
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4883
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Bit 29 of OPTSR is IO_HSLV. It ought to be read in stm32x_read_options
and written in stm32x_write_options. Adjust the bitmasks to do this.
Change-Id: I785a5291c991c98b774177f960dc58f2b5e045e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4745
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command '%s' does not have the '.usage' field filled out
While there, fix some minor typo in the help messages:
s/deasert/deassert/
s/Deasert/Deassert/
Change-Id: If3dd18265cda103ca0d05609f67f4ca58e7cbb27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5024
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove the numeric parameter <bank> from help and add it to usage
Change-Id: I630ca5450955210299f54e16fe5c9e8e51b3b266
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5022
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Chained command require a subcommand as first argument. The usage
field for chained commands is not really important because the
"help" command will list all the subcommands with their respective
usage.
Add a empty usage field on all chained command.
The command "jlink config" can be either followed by a subcommand
or used alone, so use a dedicated usage string.
Change-Id: I43c3f8a766f96a9bdab4e709e3c90713be41fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5017
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: I900924600753ee7a72ca45da13db4112ab4b1522
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5015
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: Ie69d9d6a786e1ef0abbcfd3eef89a61206238ebe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5014
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Setting of flash_sector::is_erased in flash erase and mass erase
is popular folklore. Make clear it is useless.
Change-Id: Ide397eb6d24fc8fa38931e6c8a0693d39668a5d2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4768
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Instances of struct flash_driver are never written to at runtime. For a
small amount of memory saving and also robustness (fewer things for
stray pointer writes to hit), mark them const.
Change-Id: Iadbbbc2fac0976d892699200000c5f02856729f3
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4803
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use target_addr_t exclusively for comparison of sector boudaries and
address range.
Use the last addres for both address range end and sector end.
It avoids problems with a flash bank mapped at the very end of
target address space.
Change-Id: Idf97c837453d97cbc4cf8a1c76ad799f4142f19e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4985
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Bit 4 in OPTSR is IWDG1_SW (the code originally called it IWDG1_HW, but
the reference manual refers to it as IWDG1_SW). This is broken out into
a separate variable, independent_watchdog_selection, in stm32x_options.
However, this is not necessary: bit 4 is included in the user_options
field, which includes all of bits 2 through 7, and
independent_watchdog_selection is not referenced anywhere else. Delete
the field and just rely on user_options to transport that bit, along
with all the other bits it contains, between stm32x_read_options and
stm32x_write_options.
Change-Id: I4da63df9272cf091267b956c412b95671ea1d3c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4744
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This should allow users to configure flash at >32-bit addresses.
Change-Id: I7c9d3c5762579011a2d9708e5317e5765349845c
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4919
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Recent patches for STM32L4+ assumed all STM32L4 processors have a dual-
bank option. This is not the case for STM32L4{3,4,5,6}xx processors and
therefore, these processors (like STM32L433) failed when attempting to
flash the second half of the flash memory. This patch fixed this issue.
Tested on STM32L433xC, STM32L476xG and STM32L471xG.
Change-Id: I8262ba4f05190802c5868d753f3e7af50e581811
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Reviewed-on: http://openocd.zylin.com/4913
Tested-by: jenkins
Reviewed-by: Peter Tettelaar <peter@float-iot.nl>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Mark Schulte <mschulte@lyft.com>
Added id, name, flash size and RAM size for following parts to samc20_parts[]:
SAMC20N18A
SAMC20N17A
And the following to samc21_parts[]:
SAMC21N18A
SAMC21N17A
Change-Id: Ie8cf1c531a60bfaed6e814d436d232afb89dae3f
Signed-off-by: Kevin Vermilion <kevin.vermilion@gmail.com>
Reviewed-on: http://openocd.zylin.com/4880
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
