For support of SWD we need to be able to clock out special bit
sequences over TMS or SWDIO. Create this as a generic operation,
not yet called by anything, which is split as usual into:
- upper level abstraction ... here, jtag_add_tms_seq();
- midlayer implementation logic hooking that to the lowlevel code;
- lowlevel minidriver operation ... here, interface_add_tms_seq();
- message type for request queue, here JTAG_TMS.
This is done slightly differently than other operations: there's a flag
saying whether the interface driver supports this request. (In fact a
flag *word* so upper layers can learn about other capabilities too ...
for example, supporting SWD operations.)
That approach (flag) lets this method *eventually* be used to eliminate
pathmove() and statemove() support from most adapter drivers, by moving
all that logic into the mid-layer and increasing uniformity between the
various drivers. (Which will in turn reduce subtle bugginess.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
zy1000 performance for GDB load went from 100kBytes/s
to 300kBytes/s @ 8 MHz by implementing the inner loop
of unack arm11 memory writes directly on top of the hw
fifo.
Profiling info:
78.57 0.77 0.77 arm11_run_instr_data_to_core_noack_inner
5.10 0.82 0.05 memcpy
4.08 0.86 0.04 jtag_tap_next_enabled
3.06 0.89 0.03 gdb_input
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This allows minidrivers to e.g. hardware accelerate memory
writes.
Same trick as is used for arm7/9 dcc writes.
Added error propagation for memory transfer failures in
code rearrangement.
Also the JTAG end state is not updated until after
the memory write run is complete.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It is conceivable that there could be commands in the
queue when a speed change request comes in. Flush the
hw queue before changing speed. Not observed, found by
inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
flush JTAG FIFO before reset. Fixes RCLK problems observed
w/lpc2148, but really fixes a wider range of problems.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The usual: same EBNF as in the User's Guide, full sentence helptext,
function names *are* their addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "embeddedice.h"
the following form should be used.
#include <target/embeddedice.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "minidriver.h"
the following form should be used.
#include <jtag/minidriver.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "interface.h"
the following form should be used.
#include <jtag/interface.h>
The exception is from .c files in the same directory.
Add missing COMMAND_REGISTRATION_DONE.
For now the command syntax for zy1000 needs to be compatible
across 0.3/0.4, the world outside OpenOCD interfaces to
zy1000 using the old syntax. Post 0.4 release(0.4.1 even)
I'll switch to subcommand scheme.
Switch to subcommands post 0.3 lifecycle.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The code is now much more explicit. It flushes every
N writes. For now flush every time, but tinkering with
the bridge FIFO size and how often we flush clearly
points in the direction of the Avalon write FIFO full
being the culprit.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Shifting by more than 32 is undefined for 32 bit integers according
to the C standard. Robust solution is conditional code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
