(It's really only 2 bits, but something wonky happens between gdb and
OpenOCD if I make it that size.)
Change-Id: I562a65cb0ebe5aa0edcc54c251d0fea0e26f9cb1
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Theese devices do not have a gap in sector numbering.
The driver translates sectors numbers 12 13... to 16 17... as used on dual
bank flash devices. Therefore erase of sector 12 and above fails with error
'stm32x device protected'
on F413/423.
Drop sector number translation for devices without has_large_mem flag.
Change-Id: I65531c0dfe02e2fd0f3d68f0615e0926e9901391
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4299
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A protection block comprises two adjacent sectors in dual bank mode.
As there are 64 and 128kB sectors joined in blocks 2 and 8, block size
should be computed as a sum of sector sizes.
Change-Id: Ie915df8cf7ca232c4565d7e0c514c8933e71fdfe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4271
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The CMSIS-DAP used by NXP's LS1012ARDB board only supports JTAG,
and not SWD. Calling cmsis_dap_cmd_DAP_SWD_Configure returns with an
error (and doesn't actually do anything in the debugger).
Wrap the call to cmsis_dap_cmd_DAP_SWD_Configure in a check for
swd_mode, to make sure initialisation doesn't fail needlessly.
Change-Id: Id7e568cb6e36886bd7c5b3699d198a77a51c28c9
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4294
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Because there is no instruction that moves just half of a 64-bit FPR
to/from a GPR, we need to use scratch memory for this operation. This
code can theoretically use:
1. DMI_DATA, if it is memory mapped in the target.
2. DMI_PROGBUF, if it is writable in the target.
3. A user-configured address.
I have only tested this code very lightly. One reason is that gdb thinks
that on RV32 harts every register is 32 bits wide. Another is that this
is mostly proof-of-concept to satisfy the small program buffer code
review, which I don't want to drag out forever.
Existing tests don't realize that floating support was broken with
RV32D, and don't realize that it still doesn't work because of the gdb
problem mentioned above.
This change improves Issue #110 but there's more work to be done.
Change-Id: I99b8a36e5fea26f1d9e16e36cf99adc7be26b944
The SWDIO buffer has to be enabled, by setting SWDIO_OE, for data on
SWDIO to reach the target. Explicitly do this before sending the
switch sequences for JTAG-to-SWD, etc.
This makes the code insensitive to the state of SWDIO_OE specified in
ftdi_layout_init. It used to work only on adapters with a non-inverted
SWDIO_OE inited to 1, or inverted SWDIO_OE inited to 0.
Change-Id: I4b9e520ac1c7ce2a437251a05fc036bc68de718e
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4270
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tim Newsome