The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
these commands have been introduced to ease the manipulation of CTI trough
script files, these commands are:
- $cti_name ack $event : to acknowledge a CTI event
- $cti_name channel $channel_number $operation: to perform an operation
on a specific channel, the possible operations are:
gate, ungate, set, clear and pulse
Change-Id: I35463867a3c85072f3776c3aeb1e5788953ec435
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5315
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The SWO frequency auto-detection with J-Link adapters does not work
properly in the current implementation. This is because the trace layer
has only information about the highest possible SWO frequency supported
by the adapter. With that the trace layer calculates the SWO prescaler
which usually leads to a frequency deviation greater than what is
permitted by J-Link adapters.
Move the calculation of the SWO prescaler from the trace layer into the
trace configuration of the adapter to overcome this problem.
The adapter has the necessary information to choose a suitable SWO
frequency and calculate the corresponding prescaler that complies with
the maximum allowed frequency deviation.
Tested with:
- STM32L152RC Discovery Kit (ST-Link)
- EFM32GG-STK3700 (J-Link)
Change-Id: I38ff2b89d32f0a92c597989b590afe5c75cf4902
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3903
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During code analysis and development, counting again and again the
lines to find the index of the register is a boring error-prone
brain-damaging activity.
Use the c99 syntax and add once forever the array designators to
specify the index values.
The code behavior is not changed.
Change-Id: I2c70f70794475679efb91a8dfadc00f50715bd3f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5256
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The GDB file-I/O remote protocol extension, used for implementing
the semihosting file I/O, requires the length of strings to
include the trailing zero character, as explicitly stated inside a
comment in GDB source code [1]:
/* 1. Parameter: Ptr to pathname / length incl. trailing zero. */
ARM specification for semihosting [2] requires the string length
to not include the trailing zero character, e.g. in SYS_OPEN
specifications:
"field 3: An integer that gives the length of the string
pointed to by field 1. The length does not include the
terminating null character that must be present."
The mismatch above requires OpenOCD to add "one" to the string
length before passing it to GDB. Such conversion is missing
either in the generic semihosting provider of the data, the
function semihosting_common(), and in the consumer of the data,
the gdb_server function gdb_fileio_reply().
The conversion is already implemented in the target specific
function nds32_get_gdb_fileio_info(), but it's not the preferred
place for such GDB specific requirement.
This issue affects the semihosting calls "open", "unlink",
"rename" and "system".
Remove the "+1" conversion from nds32_get_gdb_fileio_info().
Add the "+1" conversion in gdb_fileio_reply().
[1] http://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;f=gdb/remote-fileio.c;h=11c141e42c4d#l381
[2] "Semihosting for AArch32 and AArch64, Release 2.0"
https://static.docs.arm.com/100863/0200/semihosting.pdf
Change-Id: I35461bcb30f734fe2d51f7f0d418e3d04b4af506
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5322
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In preparation for supporting the ARM MCRR and MRRC commands which will
require using two 32-bit registers to read/write a 64-bit internal
register, extract the common logic to read/write from/to a register
to/from DCC and make that parameterized such that we can do this through
not just r0.
Change-Id: Iadb73f5cde8cf5961b5a18ddd198bf39d791e610
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Armv7a is able to read and write memory at un-aligned address, but
only when bit SCTLR.A (Alignment check enable) is zero and the
address belongs to a memory space with attribute "Normal" (see [1]
chapter A3.2.1 "Unaligned data access"). In all the other cases
the memory access will trigger an alignment fault data abort
exception.
Memory attributes are explained in [1] chapter A3.5 "Memory types
and attributes and the memory order model".
Disabling the MMU cause a change in memory attribute, as explained
in [1] chapter B3.2 "The effects of disabling MMUs on VMSA
behavior".
This can cause several issues. e.g. a SW breakpoint on un-aligned
4-byte Thumb instruction, set when MMU is on, can be impossible to
remove when MMU turns off.
While is possible to check all the possible conditions before an
un-aligned memory access, it's clearly more maintainable to skip
such complexity and only perform aligned accesses.
Check the alignment and eventually modify the data size before
calling the functions cortex_a_{read,write}_cpu_memory_slow().
Change the comment in the two functions above to comply with the
new behaviour.
[1] ARM DDI 0406C.d - "ARM Architecture Reference Manual, ARMv7-A
and ARMv7-R edition"
Change-Id: I57b4c11e7fa7e78aaaaee4406a5734b48db740ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5138
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added "exist=true" field to the reg_list struct to make access to the
dsp563xx registers again possible. Without it defaults to exist=false
and all the reg related functions will return nothing.
Fixes regression from b5964191f0
Change-Id: I9c256346735b8d66919c4ba83f528a8afca46ff9
Signed-off-by: Han Hartgers <han.hartgers@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5239
Tested-by: jenkins
1. Add get_thread_reg() to rtos. It's used in rtos_get_gdb_reg() to read
the value of a single register, instead of reading all register values
by calling get_thread_reg_list().
2. Add set_reg() to rtos. gdb_server uses this to change a single
register value for a specific thread.
3. Add target_get_gdb_reg_list_noread() so it's possible for gdb to get
a list of registers without attempting to read their contents.
The clang static checker doesn't find any new problems with this change.
Change-Id: I77f792d1238cb015b91527ca8cb99593ccc8870e
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5114
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
Without a better replacement of the command, it's worth fixing it.
Accordingly to ARM DDI 0403E.d, chapter C1.4.1 "Entering Debug
state on leaving reset state", to halt the core at reset both bits
DHCSR.C_DEBUGEN and DEMCR.VC_CORERESET must be set.
Current code only sets the latter bit, relying on having C_DEBUGEN
already set through other commands, e.g. "halt". This prevents the
command "soft_reset_halt" to work if issued as very first command.
Set the bit C_DEBUGEN in command "soft_reset_halt".
Change-Id: I66bfd6a0da1fca5049dea037b4d258cf6f842966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4987
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds ARMv8-M CPUs detection logic in ARMv7m target specific code.
Also adds a slightly different watchpoint manipulation logic for ARMv8-M.
This is based on ARMv8-M architecture reference manual.
Tested on ARM Musca A board.
Change-Id: I0652560954ef02c378a7067fab586edf39d3e9cc
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4997
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I1b917a4c1205115c4e0315373d81a9305e931258
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4944
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I32c43e2e47366363521fa3f387de9e2fb1c20852
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4943
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The macro TARGET_ADDR_FMT, defined in helper/types.h, already
includes the prefix "0x" in front of the hexadecimal number,
being defined as:
#define TARGET_ADDR_FMT "0x%8.8" TARGET_PRIxADDR
An additional "0x" is present in mem_ap; it prints debug messages
with a double "0x" before the address:
Debug: 2921 34180 mem_ap.c:153 mem_ap_write_memory():
Writing memory at physical address 0x0x5000000c; size 4;
count 1
Remove the incorrect hexadecimal prefix.
Change-Id: I38f19ed2a2f542bd5df53e947a2604f1cbe80e08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5222
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The ARMv7-A architecture supports super sections which allows mapping
physical addresses up to 40-bit into a 32-bit virtual address using the
short descriptor format (see ARM DDI 0406C.c section B4.1.112 for
details).
Change-Id: I8e64d0e93e36ae7a7da7b7bf2a8342856bb044f1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5212
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In preparation for adding super section decoding, do not restrict
armv7a_mmu_translate_va_pa() to 32-bit virtual addresses since ARMv7-A
processors with VMSA extensions (including LPAE) can issue wider
physical addresses. Update casting to uint32_t where necessary.
Change-Id: Id1c3d0d5ac324cbdc334259d9ea75fe4981671a1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5211
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function is not used anywhere in the tree, remove it, such that we
only have a single function moving forward that might need to deal with
short vs. long format specifics.
Change-Id: I80e81cd7eba1e028d1afaeaedb675b46c0ca6fa1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Check earlier that the read of the PAR register was successful instead
of starting the decoding and then checking for an error reading that
register.
Change-Id: Id96c2b2f76d2d1c745fcfa55ad4c1e6db92106f9
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since the first commit 09883194f8 that introduced cortex_m, the
code has a delay of 50ms after srst has been asserted.
The specific delay is implemented through the JTAG_SLEEP command
sent in the jtag queue.
To remove the dependency from the jtag queue, replace the delay
with a transport independent function.
In case of jtag transport, this change keeps the same behaviour
only if the jtag queue has been flushed before the delay. This
does not happen if the call to dap_dp_init(), few lines above,
fails while calling a dap_queue_dp_{read,write}(); in this case
the jtag queue will be flushed later, after the delay, while in
the original code the delay would follow the flushing of the
commands already queued. Anyway, this different behavior would
only happen in case of DAP already not responsive so anticipating
the delay in such error condition is not supposed to add further
problems.
Change-Id: If15978246764e4266b10e707d86c03e5ed907de7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4912
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By definition the EXTERNAL bit in Debug Fault Status Register indicates
that an external debug request (EDBGRQ) signal was asserted.
Usage example: this could be done by CTI in multicore devices in order to
halt all the cores together.
Change-Id: I7830455ce5da6702b7d08c8fa7bfe80e4d8a5055
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5157
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Part of the output is generated with log functions.
Change prototype of find_target() and use command_print() for all
the output of the command.
Change-Id: Ia9fdb653fd5b27be427381053a037545faa34414
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5092
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_dump*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia43bff112372cbb76e1aea9f59f4a9b6df05c15d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5079
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_analyze*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ie7cfd323fe591a987ea648a20be2bb9c7273dde8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5078
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of binprint() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5ebdc50417d97c791c98ac0cfe2218319809eb7f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5077
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_set() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: If00f9cfb784b53bb3df92d4469178e2f930a146a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5076
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_list() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibff636d476bcd59784ce3da5409d930225cfe637
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5075
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2150201fad3fd3bc0be89249dcbd314b38a6f860
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5074
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of dap_rom_display() and dap_info_command() to
pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Idb97b20759c03fcecbac1184c354966f469caa5f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5073
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of etmv1_analyze_trace() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic923af5480a54c7272d2ff1abbe235ba941cf1a0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5072
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_iod_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I67f594c80d6bbbbf6c9567069a545f16877b1e94
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5071
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm7a_handle_l2x_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib926cd7380ac8b6fb89f64e0a85d81d124633315
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5070
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv7a_handle_cache_info_command() to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I27f507869cb41c74722a759e69dfd45658fcd4be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5069
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv4_5_handle_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib6ab3ec2fc6504c2a0635b654697a4b6e12a3750
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5068
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib0b84c933689ac8c940c9bbe62d9c95fd015c4f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5067
Tested-by: jenkins
