Invalidate cache and restore flash XIP mode after erase and also
in error cleanup after write/erase.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If7e0c2d75f50f923e6bcbf0aa7bab53fe91b6cc8
Reviewed-on: https://review.openocd.org/c/openocd/+/8454
Tested-by: jenkins
While on it:
Define the names for the fixed flash page/sector sizes and use them
instead of magic values.
Fix memory leak on error return.
Partially backported from former upstream rp2040.c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If51c912f4d381ee47756a70f616ecdbee1ac0da7
Reviewed-on: https://review.openocd.org/c/openocd/+/8453
Tested-by: jenkins
Flash erase and write require this guard, unfortunately it is also
partially needed in the flash probe.
Partially backported from former upstream rp2040.c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie8a240e66c3ed68e08f872cbbfdd90a6d80e1f1e
Reviewed-on: https://review.openocd.org/c/openocd/+/8452
Tested-by: jenkins
Also keep size override by FLASHSIZE Tcl variable possible.
Partially backported from former upstream rp2040.c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I224c3644450e8b46e35714bfc5436219ffdee563
Reviewed-on: https://review.openocd.org/c/openocd/+/8451
Tested-by: jenkins
RP2350 can switch either core to Cortex-M33 or RISC-V.
The different architectures have to be supported as
distinct targets in OpenOCD.
Introduce 'rp2xxx _switch target' Tcl command to adapt flash
bank to architecture changes.
Keep the target and priv pointers intact until a flash operation
is finished to prevent sudden change in the middle of write/erase.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I764354ab469e253042128958dfe70c09d04d6411
Reviewed-on: https://review.openocd.org/c/openocd/+/8448
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new flash command could be handy for a reboot to BOOTSEL mode
and for making (Q)SPI flash content visible at 0x10xxxxxx
address mapping area after a rescue reset.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I1b532afcc41a4051298313e685658e86c02c53f9
Reviewed-on: https://review.openocd.org/c/openocd/+/8447
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
And add support for A1 ROM table.
TV: cortex_m smp change removed.
Fixed style problems.
'uint' replaced by unsigned int
Change-Id: Iff2710fa0734dc7074d8d490d8fae43dc27c0c2a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Luke Wren <wren6991@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8441
Tested-by: jenkins
Change the prototype of functions:
- target_run_algorithm()
- target_wait_algorithm()
- target_wait_state()
- struct target_type::run_algorithm()
- struct target_type::wait_algorithm()
to use unsigned int for timeout_ms instead of int.
Change accordingly the variables passed as parameter.
Change-Id: I0b8d6e691bb3c749eeb2911dc5a86c38cc0cb65d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7562
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nor
driver, that the struct flash_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of flash_driver's declaration in driver.h
Fix some incorrect non-const declaration and remove redundant
forward declarations.
Change-Id: I5e41d094307aac4a57dfa9a70496ff3cf180bd92
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7662
Tested-by: jenkins
Do not read ID from SPI flash and suppress autodetection
if non-zero flash bank size is configured.
Change-Id: Idcf9ee6ca17f9fa89964a60da7bf11e47b4af5e7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7241
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The num_reg_params parameter of target_run_algorithm() was not
updated when setting "sp" was introduced. Therefore "sp" as the last
register parameter was not passed to a target algo.
Introduce a new helper variable with correct count of register parameters
and use it everywhere needed.
Change-Id: I934a71380783d98917167f1569145808ef23540f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Flash read_id/erase/write operation on running target failed
in target_run_algorithm() anyway. It generated lot of error messages.
Check the target state and bail out early if target is running.
Change-Id: I903f5f38c8e61016e5002b235e5f07803bd2ec4e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI flash erase often takes longer than the fixed timeout 3 seconds.
Introduce a configurable timeout_ms parameter to rp2040_call_rom_func().
Compute the erase timeout from the number of blocks to be erased.
While on it make the timeouts shorter for connect flash, flush cache and
enter/exit xip (1 second is enough).
Change-Id: I552bfa317ee17064de3a54ec2f0c63e84ba87222
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7214
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The size of the flash write buffer should be rounded
down to the multiply of flash page size.
Using write chunks of unadjusted size results in write of chunks
unaligned to flash pages.
Change-Id: If7931362ee193dff4dc2df7ec78f13530658cf08
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7187
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it restore memory-mapped mode also after flash erase
(originally was restored after flash write only).
Change-Id: I5e153b79ac27a8439f57239ce90ce8a79c0bb8a1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7186
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Prepend stack_grab_and_prep() function name by rp2040_ prefix.
Introduce target helper variable in rp2040_stack_grab_and_prep()
and use it instead of dereferencing bank->target several times.
Move flash ID reading code to the new rp2040_spi_read_flash_id()
function.
Change-Id: I9d6e51e17e36e6230155a586065499f2f260089a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7185
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
When a struct is initialized, missing fields are already filled
with zero or NULL.
This change simplifies scripts to compare documentation and
registered commands.
Change-Id: I96fbdfa98bbb1f2b5e2a9532faf5a15cb5bc28dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6719
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
