When jtag_libusb_open() fails to find the adapter, it returns
error but left libusb initialized causing memory leak of libusb
internal data.
Issue found with valgrind when no adapter or board is connected to
the host, e.g.
valgrind openocd -f board/st_nucleo_f4.cfg
Close the libusb operations if jtag_libusb_open() has to return
error.
Change-Id: Ieb2f110be15705dafe80c099e7d83c07056c2a41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5701
Tested-by: jenkins
For jtag/drivers/bcm2835gpio dev_mem_fd has been updated within
bcm2835gpio_init with the add on of gpio to mem. This permits the
access to memory of GPIO without the need for root access.
For failed attempt, a fallback to original memory follows.
It should be noted that any printed error is relative to original
memory ("dev/mem").
Tested on EFM32GG12B390F board
Change-Id: I4540bdf62fb3b91a51221e277881adfae138dcc5
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5568
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new stlink firmware requires opening the AP before issuing
any operation.
In the current code we have a 'questionable' check about the core
model to set the TAR autoincrement, that is issued without opening
the AP, thus causing a STLINK_BAD_AP_ERROR.
Modify the AP open API to handle this case and open AP#0 before
the memory access to check the core model.
Change-Id: I576955b5094bd41d63ff1fbad7b4fd9433253321
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5691
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Firmware v2j28 introduces the API to open and close the AP, but
closing AP always returns error 0x1d (STLINK_BAD_AP_ERROR).
Ignore the error returned by the bogus firmware on closing AP.
Change-Id: I992ddbf7acb10f1d376ed8f781eeb3344605b85d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5683
Tested-by: jenkins
When the transport is not specified, OpenOCD uses the first listed
by the selected adapter driver.
The old HLA driver for stlink lists SWD as first. The new driver
dapdirect instead lists JTAG, making more difficult a fallback to
HLA when dapdirect is not available due to old stlink FW.
Plus, in case of JTAG wiring, SWD is still possible, while the
opposite is not.
Reorder the list of transports to grant the default to SWD.
Change-Id: Id9c529e921b148d5b352d4603a9028c2a5f15d83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5538
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Now that SWIM is not accessed through HLA anymore, decouple the
SWIM code and remove the conditional execution.
Fix the inconsistency of the return type for stlink_usb_state() in
case of SWIM (returns ERROR_OK while type is enum target_state)
introduced by commit 3de6b5f6e5 ("jtag/drivers/stlink_usb :
implemented and repaired SWIM support").
The code added by commit above in stlink_usb_state() is an hack to
reuse existing HLA API to perform a reconnect.
Move the SWIM specific code from stlink_usb_state() to a dedicated
stlink_swim_op_reconnect() that provides consistent data type.
Change-Id: I3fe175fef00b0735bea6139b057f217a080c9d38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 3de6b5f6e5 ("jtag/drivers/stlink_usb : implemented and repaired SWIM support")
Reviewed-on: http://openocd.zylin.com/5532
Tested-by: jenkins
Thanks to API separation between SWIM and the other transports, we
can easily split the memory read/write for SWIM from the rest of
the code.
While there, use the macro STLINK_DATA_SIZE as size of data chunks
that can be read/write in SWIM. This was not implemented before.
Change-Id: I7d913c92539007e4d914480bacc0126a8f0e9705
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5531
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
In the driver's code it's widely used the enum hl_transports for
any check concerning the current transport, even for the non-hla
transport dapdirect.
The driver already provides a stlink specific enum stlink_mode
that can be used in place of the hla one.
Replace the hla enum with the stlink one allover the code.
Introduce a hla specific wrapper stlink_usb_hl_open() to cope with
the only API that requires the hla specific enum.
The overall behaviour is not changed, with exception for a debug
message in stlink_usb_open() than now prints the numeric value of
stlink enum in place of the numeric value of the corresponding hla
one.
This change prepares the road for moving SWIM transport out of hla
by removing any reference to the macro HL_TRANSPORT_SWIM from the
stlink driver.
Change-Id: Ieeea34f312245a94bfc1333087afdb8eb9f77139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5526
Tested-by: jenkins
For void functions, a return as last statement is useless.
Remove it.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types RETURN_VOID -f {} \;
Change-Id: Ie0616fe98623f30d2d7b04ac9517d669774092de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5622
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Functions that have no parameters should use "void" as parameter
in the function declaration.
Issue identified and fixed by script checkpatch from Linux kernel
v5.1 using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_WITHOUT_ARGS --fix-inplace -f {} \;
Change-Id: If104ac75b44e939ec86155ff7b5720f2e33c6b39
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5621
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
By default the list of VID/PID is empty so if ftdi_vid_pid is not called
then no matches are attempted. The only message is at -d3:
Command 'init' failed with error code -100"
Check for this condition explicitly to make life easier for people
configuring adapters.
Change-Id: If0f93370c9e9ddc9700aae7c346c1c6dd319152e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5440
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
scan-build-9:
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1075
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1275
ulink_append_xxx_cmd() functions allocate memory for cmd
and then call ulink_allocate_payload(), which allocates cmd->payload_out
or cmd->payload_in.
ulink_append_queue() checks the size of queue and if the new payload
does not fit, calls ulink_execute_queued_commands() and then
ulink_post_process_queue(). If any of these two fails, an error is
returned, allocated cmd struct leaks and the queue is left in an undefined
state.
Change ulink_append_queue() flow to proceed to appending cmd to the queue
even in the case of fail in previous ulink_execute_queued_commands()
or ulink_post_process_queue(). In case of fail then clear the queue
including the last appended cmd.
Change-Id: I967c07af19e9020c93bcb4ef403cf1f557dd1db1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5370
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Access to field 'payload_in' results in a dereference
of a null pointer (loaded from field 'queue_start')
File: src/jtag/drivers/ulink.c
Line: 2216
Set input/output_signals conditionally if ulink_append_get_signals_cmd()
and ulink_execute_queued_commands() returns no error.
Do not fail driver initialisation as the signals are only printed.
Change-Id: I6c842f0e9a604712abf7444a2fa95ba5810de1ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5520
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
As a consequence of a previous failed SWIM command any
subsequent attempts to enter SWIM mode fails. Change
stlink_usb_mode_enter to use stlink_usb_xfer_noerrcheck
instead.
Change-Id: I5c6a1a8e68d3dc77ec37264880383366fa6a75d9
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5547
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In order to extend the driver to support stlink-server over TCP,
we should always use a valid endpoint, as stlink-server is not permissive
and do not accept the invalid STLINK_NULL_EP.
STLINK_NULL_EP value was used for commands without an expected reply,
this value could be replaced with a valid endpoint without any impact
when the size is set to zero.
Change-Id: I003ad364e03d3a10bc036772db86310d996cbe81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5455
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The usleep() function, and its associated useconds_t type
specifier, has been obsoleted by POSIX.1-2008.
OpenOCD has 28 call to usleep(), that should be migrated to the
replacement nanosleep(), but due to the different prototype
int nanosleep(const struct timespec *req, struct timespec *rem);
this can take some effort.
The type useconds_t is used in only one case, where it's used both
as parameter of usleep() and as value passed to LOG_DEBUG(). Due
to different implementation of useconds_t, there are cases that
trigger a compile warning in LOG_DEBUG() when useconds_t is more
than 32 bit.
E.g. with unistd.h in MinGW 4.x, useconds_t is defined as unsigned
long, thus being 32 or 64 bits depending on the target.
Replace the only instance of useconds_t.
Change-Id: I21724f8b06780abdb003a57222ff1d6840ff5419
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5544
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Return bool value in functions that return bool.
Change return type to bool to function is_gpio_valid().
Change-Id: Ic2e62be737772b22e69881c034956549f659370b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5552
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
While stlink v2 allows setting the jtag clock frequency till a max
of 18 MHz, the firmware seams unstable and not properly working.
Remove the entry for 18 MHz, at least until a fix get available.
Change-Id: I503e1b6a5709b5fbf1f1147fd3b5f34a0c5ee98c
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5465
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The XDS110 supports alternate configurations, each of which has
a unique vid/pid:
0451/bef3 -- Standard (legacy) configuration
0451/bef4 -- Drag-n-Drop configuration
1cbe/02a5 -- CMSIS-DAP 2.0 on BULK interface configuration
It's not important to OpenOCD what the differences are except
that OpenOCD needs to know how to connect using the different
vid/pids and, in the case of the last one, use a different
interface for the debug connection.
Updated the XDS110 source to search for all possible
configurations, and updated the udev rules file to enable
user access to the alternate configuraitons.
For the curious, you can download the latest XDS emupack from
software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds_software_package_download.html
Install to an empty directory, and documentation for the
XDS110 is located in the .../ccs_base/common/uscif/xds110
of the installation.
Updated for comments in code review. Changed const variable
names to lower case. Reworked interface/endpoint setting
to use arrays suggestion.
Change-Id: Icc9d11c6618f43d87ae8171c78ebf238800d3ac2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5494
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Arrange all commands under a top level xds110 command. Fix
documentation to properly reflect the current functionality.
Also updated the links in the document to the new permanent
links for the XDS110 only support.
Patch updated for comments from code review. Return
ERROR_COMMAND_SYNTAX_ERROR for wrong number of args in
commands. Added deprecated commands to src/jtag/startup.tcl.
Change-Id: Ica45f65e1fdf7fa72866f4e28c4f6bce428d8ac9
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5495
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Starting with XDS110 firmware version 3.0.0.0, the peak TCK
frequency became 14,000 kHz. So the delay count calculation
in the current driver has been updated to use the new
formula for setting the TCK speed depending on which version
of the firmware is detected. And because of the changes, the
default TCK settings for the XDS110 based Launchpads can be
adjusted to take advantage of the higher TCK performance.
Note that the values used have been determined through
testing in the automated test labs to be the highest TCK
frequency with the XDS110 that are still reliable.
Different boards have a different peak TCK setting that
should be safe.
Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5493
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Old ST-LINK DFU returns an incorrect serial in the USB descriptor
example for the following serial "57FF72067265575742132067"
- the correct descriptor serial is:
0x32, 0x03, 0x35, 0x00, 0x37, 0x00, 0x46, 0x00, 0x46, 0x00 ...
this contains the length (0x32 = 50), the type (0x3 = DT_STRING)
and the serial in unicode format.
the serial part is: 0x0035, 0x0037, 0x0046, 0x0046 ... >> 57FF ...
this format could be read correctly by 'libusb_get_string_descriptor_ascii'
so this case is managed by libusb_helper::string_descriptor_equal
- the buggy DFU is not doing any unicode conversion and returns a raw
serial data in the descriptor:
0x1a, 0x03, 0x57, 0x00, 0xFF, 0x00, 0x72, 0x00 ...
>> 57 FF 72 ...
based on the length (0x1a = 26) we could easily decide if we have to fixup the serial
and then we have just to convert the raw data into printable characters using sprintf
example for an old ST-LINK/V2 standalone:
before : 'W?rreWWB g'
after : '57FF72067265575742132067'
=> same as the displayed value in STM32CubeProgrammer
tested using these commands
using the buggy serial
-c "hla_serial \x57\x3f\x72\x06\x72\x65\x57\x57\x42\x13\x20\x67"
using the computed serial
-c "hla_serial 57FF72067265575742132067"
Change-Id: I1213818257663eeb8e76f419087d3127d0524842
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5396
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduce a callback function that could be passed to jtag_libusb_open
to permit adapters to compute their custom/exotic serials.
the callback should return a non NULL value only when the serial could not
be retrieved by the standard 'libusb_get_string_descriptor_ascii'
Change-Id: Ib95d6bdfc4ee655eda538fba8becfa183c3b0059
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5496
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
TCK during nSRST assert/deassert code.
To support LPRF targets (CC13xx/CC26xx), TCK must be toggled
for 50 ms while nSRST is asserted and right after it is
released. This allows the core to halt in boot ROM before
code is run that might interfere with debug access.
The current routine has two issues. It shouldn't be run at
all if the target is using SWD. And the delay needs to
be a real-time 50 ms, so the number of TCK periods should
be calculated off the set speed.
Change-Id: If993031b84cf2a505ea67a6633602c4b01cd8e1e
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function ftdi_set_signal() does not propagate the pin change
until next call to mpsse_flush(). Current code does not toggles
immediately the reset pins if polling is turned off.
Call mpsse_flush() at the end of ftdi_reset().
While there, remove the duplicated LOG message.
Change-Id: I79eacfe4fc32b5cdf2dc1b78f3660d96988466bc
Fixes: 8850eb8f2c ("swd: get rid of jtag queue to assert/deassert srst")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5431
Tested-by: jenkins
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The name 'common' does not make sense anymore. While at it,
remove some unnecessary #includes.
Change-Id: If9798a5cce179438d89428a598d8ca05c8e5f20c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5434
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Supporting two libusb versions provides additional development challenges
without additional advantage. In most cases we need to patch libusb0_common and
libusb1_common without real ability to test libusb0_common.
Change-Id: Icbb19c6809b14533fe2acf7a877377b3be4cbd61
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/5432
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
Reuse the existing tracing functionality of HLA mode to support
tracing in DAP direct mode.
Change-Id: I75a01e88ba5d3e45717e4108b99697ac3225db9e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5409
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
We have the macro ARRAY_SIZE() already available. Use it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ARRAY_SIZE -f {} \;
Change-Id: Ic7da9b710edf118eacb08f9e222f34208c580842
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5198
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command CMD_STOP_SIMU had been defined in jtag_vpi for a long time
(since the beginning?) but has not been utilized until now.
Its purpose is to signal to the jtag_vpi server (i.e. the RTL
simulation software) that the simulation shall be stopped.
This commit adds a TCL configuration command that selects whether
CMD_STOP_SIMU will be sent to the jtag_vpi server when OpenOCD is
about to exit. This functionality is off by default to maintain
identical behavior as in previous OpenOCD versions, unless the user
enables it explicitly.
Change-Id: If3894af6efa61038ccf6c9191f664e2128f2ef11
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5407
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While ST internal documentation for STLINK-V3 reports that 8 bits
read/write commands handle 512 bytes of data, a firmware bug makes
it crashing on high data size.
This is fixed with firmware V3J6 (shipped together with V2J36).
Check for firmware version to use the proper data size.
Change-Id: Iaba6cd26bbe130097c1c19de610680e0e8b69bfc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/259/
Reviewed-on: http://openocd.zylin.com/5408
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit [1] was submitted in gerrit well before the conflicting
commit [2] get merged in master branch. While it was fine
committing in master branch [1] alone, it should not be
committed "as is" after [2].
Unfortunately gerrit did not complained committing [1] after [2].
The result is that master branch does not build anymore when the
driver xlnx-pcie-xvc is enabled at configure time by the optional
flag --enable-xlnx-pcie-xvc.
Apply to the driver the required changes as in [2].
While there, remove the duplicated struct xlnx_pcie_xvc_transports
and the struct field already implicitly initialized to zero.
[1] ff6d0704ec ("jtag: drivers: xlnx-pcie-xvc: Add support for
Xilinx XVC/PCIe")
[2] efd1d64222 ("adapter: switch from struct jtag_interface to
adapter_driver")
Change-Id: I5498479b802a231afbee1b845ae9775e1da7c728
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5402
Reviewed-by: Moritz Fischer <moritzf@google.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A USB bulk write/read operation may fail with different errors:
LIBUSB_ERROR_TIMEOUT if the transfer timed out (and populates transferred)
LIBUSB_ERROR_PIPE if the endpoint halted
LIBUSB_ERROR_OVERFLOW if the device offered more data, see Packets and overflows
LIBUSB_ERROR_NO_DEVICE if the device has been disconnected
another LIBUSB_ERROR code on other failures
Current OpenOCD code is using the transfer size based error detection.
Which may not always work. For example for LIBUSB_ERROR_OVERFLOW as libusb
documentation says:
"Problems may occur if the device attempts to send more data than can fit in
the buffer. libusb reports LIBUSB_TRANSFER_OVERFLOW for this condition but
other behaviour is largely undefined: actual_length may or may not be accurate,
the chunk of data that can fit in the buffer (before overflow) may or may not
have been transferred."
This patch is refactoring code to use actual error return value for
error detection instead of size.
Change-Id: Iec0798438ca7b5c76e2e2912af21d9aa76ee0217
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4590
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.
Access to the JTAG registers happens via the PCI Express extended
configuration space.
This can be used to debug soft-cores instantiated in the FPGA fabric.
The clang static checker doesn't find any new problems with this change.
Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
