Cores armv8m, e.g. Cortex-M33, can be instantiated without the
optional Security Extension.
In this case, the secure registers are not present and when GDB
try accessing them it triggers a set of errors.
For armv8m cores without security extension, don't provide to GDB
the description of the secure registers.
Change-Id: I254478a4cf883e85b786df3f62c726b2f40d88d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Torbjörn SVENSSON <torbjorn.svensson@foss.st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With flag --enable-verbose, configure enables compiling some
conditional code that with new gcc triggers an error:
error: '%04x' directive output may be truncated writing
between 4 and 8 bytes into a region of size 5
[-Werror=format-truncation=]
Extend the buffer to contain the full 8 bytes of %04x on a 'int'
and change the limit in snprintf.
Skip the intermediate buffer 's[4]'.
Align the code to the coding style.
Change-Id: Ifc8a6e4686555578a7355a1f6049471fd5e31913
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Karl Hammar <karl@aspodata.se>
Reported-by: Tommy Murphy <tommy_murphy@hotmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/376/
Reviewed-on: https://review.openocd.org/c/openocd/+/7403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flashing a SAMD21J17D was failing during NVM erase. The samd21
datasheet specifies that one cause of error conditions is executing an
NVM command while the previous command is still running. The solution
is to wait for INTFLAG.READY after a command is issued.
SAMD21J17A was not exhibiting this problem. Perhaps the later silicon
revision has slower NVM erase times.
Signed-off-by: Dan Stahlke <dan@stahlke.org>
Change-Id: I19745dae4d3fc6e3a7611dcac628e067cb41e0f0
Reviewed-on: https://review.openocd.org/c/openocd/+/7391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'vdebug mem_path' is reported in the documentation as
'{Config Command}', but the code sets mode = COMMAND_ANY.
The code of the commands sets some value that is only used during
the init phase, so the documentation is correct.
Change mode of command 'vdebug mem_path' to COMMAND_CONFIG.
Change-Id: Icb940fe382cbc75015273b35dcc8a88fc2a7d0ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7395
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
When target is stopped in WFI/WFE or is in an infinite loop, the
sampled PC will always return the same value.
Command 'profile' requires that distance between min and max PC
should be at least 2, which is not the case for constant PC, and
incorrectly enforces the check through as assert().
Move the code that reads the optional parameters 'start' and 'end'
and check the gap 'end - start' before running the profile.
For self-computed min and max, increase max (or decrease min) to
match the required constraint.
Drop the assert().
Change-Id: I2be8df8568ce8c889923888c492e4f7ce354b16b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7400
Tested-by: jenkins
The implementation of command 'monitor profile' has few
issues:
- the address_space is a signed int, so cannot wrap-around on
space over INT_MAX;
- max address is incremented without check for overflow;
- assert() used on errors instead of returning error codes;
- only handles 32 bits PC;
- output file created and left empty on error.
This patch fixes the first two issues, as a wider fix would be too
invasive and should be postponed in a following series.
Change-Id: Id8ead3f6db0fd5730682a0d1638f11836d06a632
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7394
Tested-by: jenkins
Clang complains about the variable 'orig_dfsr' that can be used
uninitialized both in cortex_a_read_cpu_memory() and in
cortex_a_write_cpu_memory().
The issue is caused by an incorrect error path that used to jump
through 'goto out'. The code after the label 'out' is specific to
handle the case of an error during memory R/W; it is incorrect to
jump there to handle an error during the initialization that
precedes the memory R/W.
Replace the 'goto out' with 'return retval'.
Remove the label 'out' that is now unused.
Change-Id: Ib4b140221d1c1b63419de109579bde8b63fc2e8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7393
Tested-by: jenkins
Commit 35a503b08d ("arm_adi_v5: add ap refcount and add get/put
around ap use") modifies the examine functions of mem_ap, cortex_m,
cortex_a and aarch64 by calling dap_put_ap() and then looking again
for the mem-ap and calling dap_get_ap().
This causes an issue if the system is irresponsive and the examine
fails and left the AP pointer to NULL. If the system was already
examined the NULL pointer will cause a SIGSEGV.
Commit b6dad912b8 ("target/cortex_m: prevent segmentation fault
in cortex_m_poll()") proposes a fix for one specific case and only
on cortex_m.
Modify all the examine functions by skipping look-up for the AP if
it was already set in a previous examine; the target's AP is not
supposed to change during runtime.
Remove the partial fix for cortex_m as it is not needed anymore.
Change-Id: I806ec3b1b02fcc76e141c8dd3a65044febbf0a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 35a503b08d ("arm_adi_v5: add ap refcount and add get/put around ap use")
Reviewed-on: https://review.openocd.org/c/openocd/+/7392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If multiple targets are specified as -rtos <rtos_type>, the
rtos_update_threads was called only if the last target was specified as
rtos, which is inconsistent with other checks of whether or not smp target
is an rtos one.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: Ie52bc6b6c8f841d31b9590fcbc44e985d3cba0eb
Reviewed-on: https://review.openocd.org/c/openocd/+/7244
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives a step-execution command from GDB and the target
is configured as rtos=hwthread, OpenOCD reconstructs the thread-info.
However, OpenOCD does not restore the thread id which is currently
selected by GDB. Due to this issue, OpenOCD sends the information of
wrong thread to GDB after the step execution.
This commit fixes the above issue by adding a code to save/restore the
thread id selected by GDB.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: I761a1141c04d48f1290e4f09baa7c7024f86f36a
Reviewed-on: https://review.openocd.org/c/openocd/+/7358
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives 'g' packet (read general registers) from GDB and
target is configured as rtos=hwthread, hwthread_get_thread_reg_list is
called. However, it does not check if the register valid or not. Due to
this issue, OpenOCD returns invalid register values to GDB.
This commit adds a validity check to hwthread_get_thread_reg_list. If
the register is not valid, it tries to read the register from the
target.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: Iad6424b62124271ec411b1dfc044b57dfc460280
Reviewed-on: https://review.openocd.org/c/openocd/+/7357
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang ignores that xds110_swd_write_reg() is always called with
bit SWD_CMD_RNW in 'cmd' set to zero.
It then complains that the local variable 'value' gets passed by
address to xds110_swd_queue_cmd() and in case of 'read request'
such stack address get stored for later use:
src/jtag/drivers/xds110.c:1363:1: warning: Address of
stack memory associated with local variable 'value' is
still referred to by the global variable 'xds110' upon
returning to the caller. This will be a dangling
reference [core.StackAddressEscape]
To both xds110_swd_write_reg() and xds110_swd_read_reg(), add an
assert() to inform Clang about the state of bit SWD_CMD_RNW.
Change-Id: I7687c055ec71424b642e152f478723a930966e3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7380
Tested-by: jenkins
The variable retval is assigned a value that is never used.
Scan-build reports:
Although the value stored to 'retval' is used in the
enclosing expression, the value is never actually read
from 'retval'.
Drop the dead assignment.
Change-Id: I11588dee748a55d52aa7f35bc1967b7df55af7fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7379
Tested-by: jenkins
The command should now send the full 5 byte command length, which
includes the command tag (0x19) and the 4-byte baudrate word, instead
of only the last 3 bytes of the baudrate.
Signed-off-by: Nick Kraus <nick@nckraus.com>
Change-Id: Idd6e084efd7492489aa900cdbf08f540944041cb
Reviewed-on: https://review.openocd.org/c/openocd/+/7370
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target_run_flash_async_algorithm expects the source_buffer to have
at least 2 words reserved for read and write pointers in addition to the
FIFO buffer. If the size of the data to be flashed is <= 8 bytes then
the flash function will fail with "corrupted fifo read pointer" error.
Ensure the allocated buffer is big enough to hold both FIFO buffer and
read/write pointers.
Change-Id: I09c22eaac517b8cfea8e0b463f5deb6b98afd267
Signed-off-by: Simon Smiganovski <simon.smiganovski@fruitcore.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7342
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
armv7m_start_algorithm() saves register values to arch_info->context.
armv7m_wait_algorithm() restores register values from arch_info->context.
Exclude registers with flag exist = false from both loops.
While on it refactor the register restore: introduce 'struct reg' pointer
and dereference it instead of numerous accesses by a full path
from armv7m pointer.
Change-Id: I1600084db84809ee13bcf8e7828b79f8c9ff9077
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7276
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Clang spots a potential NULL pointer dereferencing that is instead
an incorrect use of an array of pointers:
src/rtos/hwthread.c:254:32: warning: Dereference of null pointer
[core.NullDereference]
(*rtos_reg_list)[j].number = (*reg_list)[i].number;
^~~~~~~~~~~~~~~~~~~~~
The error has not been spotted before because:
- this function is not called for the first core of the SMP node,
- for the other cores on Cortex-A it still returns valid register
value for the first 12 ARM registers, then it diverges.
Also Valgrind does not spot any issue at runtime.
Address the array correctly.
While there, use DIV_ROUND_UP() macro for the computation.
Change-Id: Ib87e60e0edfd9671091f5dcfa9aedaf1aed800d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7337
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 0cedf10f8f ("Remove duplicate of a counter in
hwthread_update_threads") introduced a code bug.
In the second foreach_smp_target() loop, variable "threads_found"
gets passed to routine hwthread_fill_thread(). By removing the
counting of threads_found from the second loop, the
incorrect thread counter value gets passed to hwthread_fill_thread().
Change-Id: Ie89e53ccd28bb72b6838ef2f12106a1fe8d00994
Suggested-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The autodetection of CMSIS-DAP v2 bulk interface is tricky
as not all adapters conform CMSIS-DAP specs.
If an interface has a string descriptor containing CMSIS-DAP,
then OpenOCD did not insisted on the correct interface class
LIBUSB_CLASS_VENDOR_SPEC.
However the relaxed test caused false autodetection of v2 bulk
interface on some CMSIS-DAP v1 adapters with an additional serial
interface with the string descriptor stupidly containing
CMSIS-DAP text.
Make the test less relaxed, refuse autodetection of the interfaces
with the class number of well known functions including CDC and MSC.
Link: https://sourceforge.net/p/openocd/tickets/368/
Change-Id: I917cb257eb42aab93560cc39c61ec35a60ce52e3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7279
Tested-by: jenkins
Reviewed-by: SilverFox <yyjdelete@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable retval is assigned a value that is never used, as it
is reassigned few lines below.
Drop the dead assignment.
Change-Id: Id4e9134408fab3e04936d36e95724bf8d3ab55aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7304
Tested-by: jenkins
Clang get confused by initializing the array uint16_t lock_word[],
casting it to (uint8_t *), then accessing the second element of
the uint8_t pointer.
src/target/dsp5680xx.c:2046:41: warning: The left operand of '<<'
is a garbage value [core.UndefinedBinaryOperatorResult]
uint16_t tmp = (buffer[0] | (buffer[1] << 8));
~~~~~~~~~ ^
Fix it by replacing the array with a single uint16_t.
The code is still depending on host endianness; no fix for this is
proposed.
Change-Id: I16dfd60cab117dd145aeecf10d9593574ff233a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7302
Tested-by: jenkins
The function esirisc_jtag_recv() can be called with argument
num_in_fields = 0, for example as consequence of calling
esirisc_jtag_continue().
In this case, num_in_bytes is zero and the allocation of the
variable-length array 'r' requires size zero.
src/target/esirisc_jtag.c:133:2: warning: Declared variable-length
array (VLA) has zero size [core.VLASize]
uint8_t r[num_in_bytes * 2];
^~~~~~~~~ ~~~~~~~~~~~~~~~~
Fix it by forcing size one when num_in_bytes is zero.
Change-Id: Id764c7b5ec4f5b3c18c7da650bbff39fc98ed049
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7301
Tested-by: jenkins
Clang assumes that size could assume a value that is not 1 nor 2
nor 4. In such condition the buffer in t is allocated (size != 1)
and not initialized. This triggers an error:
src/target/openrisc/or1k_du_adv.c:655:14: warning: 2nd function
call argument is an uninitialized value [core.CallAndMessage]
crc_calc = adbg_compute_crc(crc_calc, data[i], 8);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add the default case to cover other values of size.
After this fix, clang still complains on the same line, this time
misunderstanding the limits of the loop and considering that
buf_bswap16() only swaps the first 16 bits, thus passing not
initialized value data[2] to adbg_compute_crc()
Replace malloc() with calloc() to silent it.
Change-Id: I358d7fb2ebefd69255670641bd435b770762a301
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7300
Tested-by: jenkins
All the converters functions:
h_u64_to_le()
h_u64_to_be()
h_u32_to_le()
h_u32_to_be()
h_u24_to_le()
h_u24_to_be()
h_u16_to_le()
h_u16_to_be()
have signed type in their prototype, while the function name and
all the current use cases pass an unsigned value.
Change the prototypes to use unsigned types.
Change-Id: I76dcfdd7912b81f60902184712b2907eae9843f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7299
Tested-by: jenkins
If we just invented thread 1 to represent the current execution, we
need to make sure the RTOS object also claims it's the current thread
so that threadx_get_thread_reg_list() doesn't attempt to read a
thread control block at 0x00000001.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I7f71e730d047858898297e4cb31db8e47e0c371c
Reviewed-on: https://review.openocd.org/c/openocd/+/7280
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
`xtensa_do_step` is invoked from `xtensa_prepare_resume` to silently
step over BP/WP before resuming.
For example; in the case of WPs (DEBUGCAUSE_DB), in the current
implementation `xtensa_do_step` will generate one more
`TARGET_EVENT_HALTED` after the original one caused by WP itself.
This patch moves the halted event cb call after
the step is done successfully.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9048e14fb316dc124847a42cfaefb1f76b5ce53e
Reviewed-on: https://review.openocd.org/c/openocd/+/7274
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Fix the declaration of riscv command 'set_mem_access'.
- Remove non existing riscv command 'set_scratch_ram'.
- Add riscv commands 'info', 'reset_delays'; copy the description
from the 'help' text.
- Don't add riscv commands 'set_prefer_sba' and 'test_sba_config_reg'
as they are marked as deprecated.
- Ensure that 'test_sba_config_reg' prints a deprecation warning
when used.
Change-Id: I39dc3aec4e7f13b69ac19685f1b593790acdde83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7268
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
This GPIO driver is common to SoCs that have in-order ARM cores
(BCM2835) as well as superscalar (BCM2836-7) and speculative
out-of-order cores (BCM2711).
For BCM2837 and BCM2711, the processor can dual-issue stores and
is free to merge writes to peripheral memory for pages mapped
MT_NORMAL_NC, which is the default provided by /dev/[gpio]mem.
This can cause glitches (or missing edges) on GPIO pins when
toggled with no delay, as pipelined writes to the same address
can get arbitrarily squelched.
To prevent this happening, make sure the preceding write ops are
flushed outside the shareable domain by using a memory barrier.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Change-Id: I8805cc0911667bcb9b7f4ca340d7f4f1cb25d096
Reviewed-on: https://review.openocd.org/c/openocd/+/7258
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The work area should be backed up.
The flash probe runs an algorithm on the target CPU.
The flash is probed during gdb connect if gdb_memory_map is enabled
(is enabled by default).
Without backup the target memory gets corrupted on gdb connect.
Change-Id: I3344b9dc6cbf904d49f3b05ab104b541d1d63422
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7257
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: I7c3de39fb1e6c23b76e2a0a85ab75f23aac94c4d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: Ife875a966a838c37dde987bc584ad0a1f4d020d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After merging [1] 'reset halt' does not work on not responding Cortex-M.
Relax the examined tests and try to set vector catch VC_CORERESET
if debug_ap is available.
While on it add an info about examination state to debug logs.
Fixes: [1] commit 98d9f1168c ("target: reset target examined flag if target::examine() fails")
Change-Id: Ie2e018610026180af5997d70231061a275f05c76
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6745
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When configure option --without-capstone is used, the macro
HAVE_CAPSTONE is not defined in config.h, and the following lines
are instead present:
/* 1 if you have Capstone disassembly framework. */
/* #undef HAVE_CAPSTONE */
This cause compile error with message:
arm_disassembler.h:190:5: error: "HAVE_CAPSTONE" is not
defined, evaluates to 0 [-Werror=undef]
190 | #if HAVE_CAPSTONE
| ^~~~~~~~~~~~~
This is caused by configure.ac that does not call AC_DEFINE when
--without-capstone option is present.
Fix configure.ac to always provide the autoconf macro
HAVE_CAPSTONE, with either value 0 or 1.
Change-Id: Ie5ac98b2c25746dd721812c91baaac61ec877ecd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7224
Tested-by: jenkins
Since all the device definition when accessing device from jtag is also
valid when accessing from swd, lets make sure the configuration can
handle the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5af071137fd8c3b52cc4ef72401f8eba952f9cad
Reviewed-on: https://review.openocd.org/c/openocd/+/7090
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ST-Link v2 dongles can be used with many cortex-m parts, but they have
one limitation -- they can only perform 8-bit and 32-bit writes to the
target. 16-bit writes are done using a pair of 8-bit writes. While not
usually an issue, in the case of the at91samd flash driver, the 16-bit
'command' register must have both halves written in the same
operation.
Fortunately, this register has two pad bytes above it in the address
space, making it safe to always access with 32-bit operations.
Change-Id: I44b0db9406982a8db5818c0533d3101618741db2
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7234
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The bitbang driver floods the log by many messages with very
little informational value.
Remove some LOG_DEBUGs, convert some others to LOG_DEBUG_IO.
Change-Id: I0c7539467b45543e12932c67dc71e86d58c8c6cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7220
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Make write to DP_TARGETSEL is logged the similar way as other DP register
read/writes.
While on it fix checkpatch message
'Concatenated strings should use spaces between elements'
Change-Id: I98f724c984e8c4610cc461340f4c4a7cc9627ed9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7219
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
armv7m_start_algorithm() stored all non-debug execution
registers from register cache without checking validity.
Check if the register cache is valid.
Try to read from CPU if not valid.
Issue a warning if register read fails.
Change-Id: I365f86d65243230cf521b13909575e5986a87a50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7240
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The num_reg_params parameter of target_run_algorithm() was not
updated when setting "sp" was introduced. Therefore "sp" as the last
register parameter was not passed to a target algo.
Introduce a new helper variable with correct count of register parameters
and use it everywhere needed.
Change-Id: I934a71380783d98917167f1569145808ef23540f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Flash read_id/erase/write operation on running target failed
in target_run_algorithm() anyway. It generated lot of error messages.
Check the target state and bail out early if target is running.
Change-Id: I903f5f38c8e61016e5002b235e5f07803bd2ec4e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI flash erase often takes longer than the fixed timeout 3 seconds.
Introduce a configurable timeout_ms parameter to rp2040_call_rom_func().
Compute the erase timeout from the number of blocks to be erased.
While on it make the timeouts shorter for connect flash, flush cache and
enter/exit xip (1 second is enough).
Change-Id: I552bfa317ee17064de3a54ec2f0c63e84ba87222
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7214
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The size of the flash write buffer should be rounded
down to the multiply of flash page size.
Using write chunks of unadjusted size results in write of chunks
unaligned to flash pages.
Change-Id: If7931362ee193dff4dc2df7ec78f13530658cf08
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7187
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it restore memory-mapped mode also after flash erase
(originally was restored after flash write only).
Change-Id: I5e153b79ac27a8439f57239ce90ce8a79c0bb8a1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7186
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Prepend stack_grab_and_prep() function name by rp2040_ prefix.
Introduce target helper variable in rp2040_stack_grab_and_prep()
and use it instead of dereferencing bank->target several times.
Move flash ID reading code to the new rp2040_spi_read_flash_id()
function.
Change-Id: I9d6e51e17e36e6230155a586065499f2f260089a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7185
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
swd_multidrop_select() uses its own retry loop.
If select fails, do_reconnect flag remains set on exit and causes
useless reconnect.
Clear do_reconnect flag in retry loop.
Change-Id: Ie06d6967d7f4a977774c8530bb8d4b3e5ab4f62c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7217
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Implementation of ADI v6 introduced banking of DP reg 0.
The accompanying change preventing DP SELECT write before
DP IDR read during connect was added to swd_connect_single() only.
Unchanged swd_connect_multidrop() / swd_multidrop_select_inner()
was broken as it emited DP SELECT and put DP to protocol error state.
Copy dap->select handling to swd_multidrop_select_inner().
Fixes: 72fb88613f (adiv6: add low level swd transport)
Change-Id: I514cd6d9ae2ba97ce3657b459df22638c278a0b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Scan-build reports:
Logic error: Uninitialized argument value
riscv.c:2688 2nd function call argument is an uninitialized value
This is a real error cause by running the command "riscv
authdata_write" without arguments. In such case 'value' is not
initialized and is passed to and used by r->authdata_write().
Reorganize the code to:
- detect the correct amount or command's arguments;
- drop the LOG_ERROR() on ERROR_COMMAND_SYNTAX_ERROR;
- drop the 'else' after 'return'.
Change-Id: I62e031220593b8308bc674b753e15d16d4c5c9ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7210
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Scan-build reports:
Logic error: Result of operation is garbage or undefined
riscv.c:1614 The result of the left shift is undefined due
to shifting by '4294967281', which is greater or
equal to the width of type 'target_addr_t'
This is a false warning due to clang that considers the impossible
case of 32 bits hart (xlen = 32) in SATP_MODE_SV48 mode
(info->va_bits = 48).
Under such case:
riscv.c:1614 ... ((target_addr_t)1 << (xlen - (info->va_bits - 1))) ...
the shift amount wraps around the unsigned type and assumes the
value 4294967281 (0xfffffff1).
Use assert() to prevent clang from complaining.
Change-Id: I08fdd2a806c350d061641e28cf15a51b397db099
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7209
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead nested assignment
riscv.c:459 Although the value stored to 'ir_user4_raw' is
used in the enclosing expression, the value is
never actually read from 'ir_user4_raw'
This is caused by the value reassigned in 'ir_user4_raw':
riscv.c:459 ir_user4[3] = (uint8_t)(ir_user4_raw >>= 8);
but never used.
Drop the DIY conversion in favor of h_u32_to_le() that does not
reassign the input value.
Change-Id: Ifad29f4c46d4a2d0a2f5a5c4104d768cc3db2794
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7208
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead assignment
riscv.c:716 Value stored to 'result' is never read
Remove the initialization of variable 'result'.
Change-Id: Ied67bb4fcfa5bace186522074247ead43a5d5cd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7207
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead initialization
riscv-013.c:2362 Value stored to 'control' during its
initialization is never read
Remove the initialization of variable 'control'.
Change-Id: I548f8175530b9a2aa4c1788549d6467bf9824584
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7206
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build complains about variable 'sbcs_orig' that can be used
not initialized.
Logic error: Assigned value is garbage or undefined
riscv-013.c:4468 Assigned value is garbage or undefined
This is caused by not checking the return value of the call
riscv-013.c:4466 dmi_read(target, &sbcs_orig, DM_SBCS);
In fact when dmi_read() returns error, the variable 'sbcs_orig' is
not assigned.
Check the returned value.
Change-Id: Ia9032a0229aa243138f95f4e13f765726a4ceae9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7205
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build triggers a warning:
Unix API: Allocator sizeof operand mismatch
dsp563xx.c:2143 Result of 'calloc' is converted to a pointer
of type 'uint8_t', which is incompatible with sizeof
operand type 'uint32_t'
It's a false positive because calloc() is properly used in this
case, as the uint8_t array is used in blocks of 4 elements to read
or write uint32_t values.
Either
calloc(sizeof(uint32_t), count);
and
malloc(count * sizeof(uint32_t));
keep triggering the same warning.
Drop the warning by using the constant '4' as size of uint32_t, as
already used few lines below.
Change-Id: I5bb1ece177774eefdc5d9cd049338f8f2be87cd7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Doxygen complains about:
adapter.h:120: warning: Unsupported xml/html tag <signal_name> found
Move the text in double quote to remove the warning.
Change-Id: Ia4ead5caa83c84e10ee2b2359048c282892170b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 82fd400542 ("jtag/adapter: Add command 'adapter gpio'")
Reviewed-on: https://review.openocd.org/c/openocd/+/7202
Tested-by: jenkins
The copyright date for OpenOCD project has never been updated.
Add the range till current year.
Change-Id: I42c7e3b2bf2e3a486bf836d063460dfa7b40d24d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7201
Tested-by: jenkins
When checkpatch is run with command line flag --no-tree, it cannot
find local 'companion' files and has to skip loading them.
This has caused issues with change https://review.openocd.org/7211
on jenkins.
Skip loading 'tools/scripts/camelcase.txt' with flag --no-tree.
While there, rewrite the associated error message.
Change-Id: I6ede7b16f9ccd77b9118fd9be7ada07a1ac96952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7212
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Include hints on how to skip some of the tests in some really
exceptional case.
Note: the file includes an example of commit message with a signed
off tag that triggers a checkpatch error.
Let checkpatch to ignore BAD_SIGN_OFF error.
Checkpatch-ignore: BAD_SIGN_OFF
Change-Id: I05bf0ab8008649f3f9b38452e056dc3df83a1a4f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5609
Tested-by: jenkins
In OpenOCD documentation is in folder "doc".
Fix search path of 'checkpatch.rst'.
This file is used to provide verbose explanation of failing
checks while using command line flag '-v'.
Change-Id: Id864369d371cbd5a24e76bf90c54ff03159051c3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7022
Tested-by: jenkins
Linux has some automatically generated macros that can trigger
camelCASE check. This forces checkpatch to only detect the pattern
[A-Z][a-z]|[a-z][A-Z]
for adjacent case transition.
In OpenOCD we do not have such case, so extend the check to
[A-Z][0-9_]*[a-z]|[a-z][0-9_]*[A-Z]
and remove the detection of Linux special cases.
Change-Id: I82cb6dc668edbb093f68991337da1f4b933f1fac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7152
Tested-by: jenkins
OpenOCD has to deal with CamelCase API, mainly from inttypes.h,
jimtcl, libusb and Windows.
Modify checkpatch script to load from a file the list of allowed
CamelCase symbols.
Populate the file 'camelcase.txt' with the symbols that OpenOCD
has to get from external library, plus some of the symbols that
should be fixed later.
Enable CAMELCASE test in configuration script.
Add generated files to .gitignore.
Remove the check for 'known' CamelCase symbols from include folder
as this will not work on OpenOCD Jenkins, as it run checkpatch on
already patched code.
Change-Id: I0415af673ed9f985394405ff8f1eeec81135410a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6170
Tested-by: jenkins
The script 'checkpatch.pl' is part of the automatic tests used by
Linux Maintainers and developers to test new patches.
The Linux development process is e-mail base. An error reported by
checkpatch is not a blocking point; the developer can explain in
the e-mail why he is submitting a patch that fails at checkpatch
or that is in violation of the coding style. It's up to the
maintainer to decide to accept or reject the explanation and then
the patch.
The OpenOCD development process relies on Gerrit and Jenkins as
front-end tools. Jenkins tests every new patch with checkpatch
and then builds the new code. If checkpatch fails, Jenkins adds a
failure label to the patch; this often causes the patch to get
ignored by maintainers that considers it as 'not ready'.
Checkpatch can be instrumented to ignore some test, but this has
to be specified in the command line or in the configuration file.
Let checkpatch extract from the patch's commit message the new
field 'Checkpatch-ignore:' that lists the additional tests that
has to be ignored for that patch only.
The developer that detects as error or a limitation in checkpatch
can add the field and the problematic test in the commit message
and re-push the patch.
The maintainer should check the list of tests and decide how to
proceed.
Change-Id: Iafc1b2893a07c7b3fc7e3ad15bd694aba9bd8519
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6169
Tested-by: jenkins
OpenOCD uses longer lines (120 char vs 100) and smaller tab size
(4 char vs 8) wrt Linux kernel coding style.
Clearly deep level of indentation is bad for code readability,
but let's be more permissive on the indentation level.
Change-Id: I16cf0b761145ec6072509dc26bb09c693e89e608
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6167
Tested-by: jenkins
With the new checkpatch it's not possible to send in one shot a
set of patches through stdin because the Signed-off-by tag present
in each patch will trigger the error of duplicated Signed-off-by.
Use the new command-line flag '--git' to let checkpatch to extract
the patches from git and analyse them one-by-one.
While there, add the SPDX tag to the script.
Change-Id: I74791b627b8cd68f2d49146d15ae35bbc610e64e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6166
Tested-by: jenkins
Fix the patch of the external helper spdxcheck.py accordingly to
OpenOCD folder structure.
List only the current LICENSES subfolders in spdxcheck.py .
Enable the check for SPDX headers.
Extend the check for TCL and Makefile.am files.
Change-Id: I0a40da0127746217ee0ac416058d5ceb922428ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5608
Tested-by: jenkins
The new checkpatch from Linux kernel does not recognizes the
specific types used in OpenOCD, e.g. "fd_set" and "Jim_Obj".
As consequence, it consider "fd_set" as the name of a variable,
then misinterpret the asterisk for the pointer "fd_set *" as a
multiplication, thus suggest to add a space after the asterisk
and replace "fd_set *x" with "fd_set * x".
Let checkpatch recognize the typedef used in OpenOCD.
Change-Id: Ibc295e6a8b47ffa88b50a6d510b7970760e5199d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5607
Tested-by: jenkins
Prevent checkpatch to complain for commits that add new entries
in the dictionary of misspelled words.
Remove the ignore flag TYPO_SPELLING from .checkpatch.conf, now
spelling is functional.
Change-Id: I911dedafc243e34f753d2be687977066719ff2eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5123
Tested-by: jenkins
checkpatch.pl looks for Linux kernel specific paths and files
to check source tree. As openocd misses kernel files it ends
with this error message:
Must be run from the top-level dir. of a kernel tree
This patch also renames 'kernel' -> 'openocd'
in source tree-related messages.
This is the old commit c5d8988316 ("checkpatch.pl: check for
openocd tree, not for kernel tree") re-applied.
Also remove the flag "--no-tree" from .checkpatch.conf, not
required anymore.
Change-Id: I336a66558c75494b7ae339ea63559c31f23aad84
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5122
Tested-by: jenkins
This is needed to avoid checkpatch barking on already committed patches.
This is the old commit cadd519715 ("checkpatch: treat jenkins as
valid email") re-applied.
Remove the flag BAD_SIGN_OFF, not anymore needed.
Change-Id: I6744f80de982f7934f3a5197ac2df1c29962cbd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5120
Tested-by: jenkins
It's commonly considered that user-visible strings should not be split
to different lines in the sources to ease grepping for them. Hence,
checkpatch traditionally makes an exception for logging functions,
lines having them can be of arbitrary length.
OpenOCD uses different (from Linux, the kernel) names, so they need to
be added to avoid false positives.
This is the old commit bb3cd6ec43 ("checkpatch: add logging functions")
re-applied and updated.
Change-Id: Ib18e4532cf7e1f79821b74c9bb6134a8a4e8be1b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5119
Tested-by: jenkins
The script checkpatch.pl require some adaptation for OpenOCD that
cannot be achieved through the config file .checkpatch.conf; the
script's code has to be modified.
To merge new version of the script from Linux kernel it becomes
relevant highlighting the changes, while minimizing the diff wrt
the initial script.
Add the perl variable '$OpenOCD' and suggest how to highlight
changes.
Change-Id: Ia8d26426850008f0465858a1d84cc774bc1146ed
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7021
Tested-by: jenkins
This initial setup covers the old commits:
commit 09571d62bc ("checkpatch: disable extern and switch indent checks")
commit 2f6f7c442d ("checkpatch: remove typedef check")
commit 9ad57e96b3 ("checkpatch: remove volatile check")
commit 3da783f628 ("checkpatch: increase line length to 120")
commit 2af5b97ba3 ("checkpatch: remove __packed and __aligned checks")
commit 164450a015 ("Change checkpatch.pl tab expanding to 4 characters.")
It also skips the check for SPDX_LICENSE_TAG, not implemented in
OpenOCD yet.
Extend to the check in 'strict' mode and skip all the check that
cannot apply on OpenOCD project.
Change-Id: I6c3bdf27465dc563464fbc8fafbaec696e287624
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5117
Tested-by: jenkins
Replace existing checkpatch script with the one available in the
latest Linux kernel.
Add also from the same kernel version the spelling database and
the script spdxcheck.py, even if the script cannot be found by
checkpatch in the current path.
Add an empty "const_structs.checkpatch" file and an initial
"spdxexclude" file.
The script as is doesn't work properly in OpenOCD project.
Further patches in this series are required.
Gerrit will use the checkpatch in this commit to test/build the
commit itself. A minimal configuration file is then required to
avoid a failure in the test/build process.
This commit includes the OpenOCD commits:
commit 164450a015 ("Change checkpatch.pl tab expanding to 4 characters.")
commit 667d510dab ("checkpatch: fix false indent trigger")
already merged in upstream checkpatch in kernel v6.0-rc3.
Change-Id: Ic9cdecff2df0a1e23cdb01d10f14c5988480b8d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5116
Tested-by: jenkins
When FreeRTOS (at least) is compiled with -flto, this leaves certain
static symbols with .lto_priv.0 appended to their name. Arguably this
could be considered to be a gdb or gcc bug, but one place to resolve it
for OpenOCD usage is here at symbol lookup time.
Note that the ".0" is for the first such instance of the variable as a
static; additional ones would end up as ".1", ".2", etc, and are not
considered here.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: I03580b45e8ea364392ef4e05c96276416b390cb0
Reviewed-on: https://review.openocd.org/c/openocd/+/7179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This updates the FreeRTOS module to use the M4F FPU stacking also for the
FPV5_SP and FPV5_DP FPUs, which are found on the Cortex-M7. The FPUs are
in fact different than the FPV4_SP found on the M4, but the register
stacking is the same.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I74c45d2cfb55f55e6c557f2450068ad3c2fe9497
Reviewed-on: https://review.openocd.org/c/openocd/+/6939
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The method soft_reset_halt is optional; no need to add an
empty function.
Remove mips_mips64_soft_reset_halt() and move the TODO comment
in struct target_type.
Change-Id: Id541a75e7a08645568961d59b73a120c2238701f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7184
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I2b6a8365f554e332520fa77ccf076188083a932f
Reviewed-on: https://review.openocd.org/c/openocd/+/7122
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
New GCC reports 5 warning:
src/jtag/drivers/ep93xx.c: In function 'set_gonk_mode':
src/jtag/drivers/ep93xx.c:123:47: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
123 | devicecfg = *((volatile int *)(syscon + 0x80));
| ^
src/jtag/drivers/ep93xx.c:124:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
124 | *((volatile int *)(syscon + 0xc0)) = 0xaa;
| ^
src/jtag/drivers/ep93xx.c:125:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
125 | *((volatile int *)(syscon + 0x80)) = devicecfg | 0x08000000;
| ^
src/jtag/drivers/ep93xx.c: In function 'ep93xx_init':
src/jtag/drivers/ep93xx.c:182:46: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
182 | gpio_data_register = gpio_controller + 0x08;
| ^
src/jtag/drivers/ep93xx.c:183:56: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
183 | gpio_data_direction_register = gpio_controller + 0x18;
| ^
Change pointer type to allow pointer arithmetic.
Change-Id: Idd78a7156bdf99df2624043e924b8e54a0588ace
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7180
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The script configure.ac checks for the presence of system include
files required to build OpenOCD.
It incorrectly check for:
dirent.h
pthread.h
ifaddrs.h
net/if.h
that are never included by OpenOCD source code, plus the generated
macros:
HAVE_DIRENT_H
HAVE_PTHREAD_H
HAVE_IFADDRS_H
HAVE_NET_IF_H
are never used in OpenOCD source code.
It also checks for the system function:
vasprintf()
that is never called by OpenOCD source code, plus the generated
macro:
HAVE_VASPRINTF
is never used in OpenOCD source code.
Drop the checks for the unused system include files and the unused
system function.
Change-Id: I68c1b1a1be268a830247fc489f210877c32d7d23
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7175
Tested-by: jenkins
Commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change") replaces the jimtcl command "expr" with an openocd
version that detects the TCL syntax change and prints a warning.
The openocd "expr" command will be dropped after v0.12.0,
One side effect is that openocd invokes polling the target after
every openocd command, causing scripts that use several "expr"
commands to run much slower; see [1].
The proper fix would require openocd to invoke polling only at the
time period deadline, instead of at each command. Such fix is too
risky to be applied now, due to short time before v0.12.0-rc1.
As a temporarily workaround, let openocd to detect the "expr"
command and skip the polling.
This will be dropped together with the openocd "expr" command.
Change-Id: I8151aa28694817001046165a15475d64896f985e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/362/ [1]
Fixes: c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr' syntax change")
Reviewed-on: https://review.openocd.org/c/openocd/+/7174
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Variables should not be declared in the include file, otherwise
multiple include will cause multiple instances.
Move the declaration in the C file and make it static.
Change-Id: I8b4884cba643a792a78df4e123aa324b19d92279
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7172
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
The function set_log_output() has never been used after the drop
of eCos build with commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") in 2012.
Drop it!
Change-Id: I070b688061776c7ced5db18f738d78a4a7623726
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7164
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For some configurations, notably on DAP systems, resolve issue where single-stepping does not always transition into the HALTED state.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I053f4eaffad8c3228878ba87580ada640e4bd2fe
Reviewed-on: https://review.openocd.org/c/openocd/+/7150
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This reverts commit dac90163a2 (".gitignore: add cross-compile
*-libtool") [1] merged in May 2022.
The old build system of OpenEmbedded used to rebuild and rename
plenty of tools to discriminate between host's and target's tools.
This creates, among others, the odd file "$CROSS_COMPILE-libtool"
that was addressed by the patch [1].
OpenEmbedded has dropped this odd behavior with patch [2], present
in OpenEmbedded 4.0 "kirkstone" tagged on April 2022.
In current situation:
- old OpenEmbedded use OpenOCD v0.11.0 or older, so will not use
the patch [1];
- new OpenEmbedded has [2] applied, so will never take benefit
from the patch [1].
As consequence, patch [1] is completely useless and keeping it in
OpenOCD can even be misleading.
Revert patch [1].
Change-Id: I75793fce82a5297d74af72e620c4e63cd5b15f90
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://review.openocd.org/6960 [1]
Fixes: dac90163a2 (".gitignore: add cross-compile *-libtool")
Link: https://git.openembedded.org/openembedded-core/commit/?id=4b308773eca7 [2]
Reviewed-on: https://review.openocd.org/c/openocd/+/7161
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I24bd362eeb6b74f09aceb9b757d45cbfa4afe334
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7160
Tested-by: jenkins
Replace the GPLv2-or-later boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I380d552940f1c405309a3346454251c0e80b5a45
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7159
Tested-by: jenkins
Replace the BSD-3-Clause boilerplate with the SPDX tag.
Add the SPDX tag and the copyright to two makefiles that were
added by TI with the other files in their respective folder.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I3ad1b2dbdb6054b74dcc26e394c9223ba0427caf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7158
Tested-by: jenkins
These files are not built in OpenOCD and are not in conflict with
OpenOCD license.
Replace the GPL boilerplate with the SPDX tag.
Add the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I934e4add24098f0e8574120b3bc32e9bcf166abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7157
Tested-by: jenkins
Put the SPDX tag alone in a comment in the first line of the file.
Replace the obsolete GPL-2.0+ tag
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ia91b0f7da42c439b6340bbe81983b86b68f6d65c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7156
Tested-by: jenkins
We have left the camelcase symbols *xPSR* for some time, to avoid
any conflict with possibly pending patches in gerrit.
With the approaching v0.12.0-rc1, it's time to revisit it.
The patches in gerrit that conflict with this rename are all not
merge-able due to conflicts or due to negative review.
Drop these CamelCase symbols.
Change-Id: Ifbac4c1df9cc55994e024971a2aaebeed2ea4ed3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the help of checkpatch, some CamelCase symbol passed
through the filter of maintainer's review.
Drop them.
Change-Id: If5fb07b2ffb89e853dd2a61f20d4134aa6e20d24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 48f267d4ad ("flash/stm32l4x: avoid using magic numbers for device ids")
Fixes: 5ab74bde06 ("semihosting: User defined operation, Tcl command exec on host")
Reviewed-on: https://review.openocd.org/c/openocd/+/7154
Tested-by: jenkins
Use indirect enum IDs to access XDM registers in preparation for supporting both NAR (JTAG) and APB (DAP). No new clang static analysis warnings.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I0b742fe4661ff3cf609454b8650493d141a1e1ff
Reviewed-on: https://review.openocd.org/c/openocd/+/7143
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As a follow-up of talks between JEDEC and STMicroelectronics,
JEDEC agrees to let OpenOCD project including the manufacturer's
identification code list extracted from JEDEC JEP106 document and
to let OpenOCD being updated regularly using the future JEDEC
JEP106 document versions. JEDEC requires OpenOCD to report the
origin of the JEDEC JEP106 manufacturer's identification code list
together with the JEDEC copyright.
As agreed with JEDEC, add in the file jep106.inc:
- the SPDX tag with the GPL license of the OpenOCD project;
- the JEDEC copyright;
- the text provided by JEDEC reporting the origin of the JEDEC
JEP106 manufacturer's identification code list.
While there:
- add a line reporting the version of the JEP106 document that was
used for the current code list extraction;
- remove the obsolete comment, as the script for extraction is not
working anymore; keep the script as example.
Change-Id: Iaa76716db14e15ffca04fcf7d8c27bb85a27ba10
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The full text of the license is already available in the file
LICENSES/preferred/BSD-2-Clause
and there is no need to replicate it in the source code.
Remove the BSD-2-Clause boilerplate but, preserved the copyright
notice because it provides the info on the copyright holder.
Change-Id: I162aa4ad06b551f1a71a28d049cb797ee8ab5a01
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7146
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
In the app-trace module we are polling the target in the while loops
outside of the server.c
In that loops, we need to catch ctrl+c signal by checking shutdown_openocd
status
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Id87c709a01470bf6d3642078b160a68ca85f4406
Reviewed-on: https://review.openocd.org/c/openocd/+/7142
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
kinetis.c:994:61: error: '%u' directive output may be truncated
writing between 1 and 10 bytes into a region of size 4
[-Werror=format-truncation=]
tested with scan-build-14
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I72d141a3f8e19ca3596beee2be8434fc8492946f
Reviewed-on: https://review.openocd.org/c/openocd/+/7140
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While on it rename misleading write_algorithm_sp to write_algorithm_stack
and change messages referring 'stack pointer' instead of stack.
No functional change.
Change-Id: Ibb9897d3f01734812ed0f8bc8cd43b935a573f8a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7132
Tested-by: jenkins
Reviewed-by: Salvatore Giorgio Pecorino <salvatore-giorgio.pecorino@st.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value of struct flash_driver::command can be NULL when the
flash driver does not need to add any new command.
Remove empty command definitions.
Change-Id: I5413967d4069030234469822d24e9825425ae012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7120
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Document the process of using buildroot to build a big-endian
binary of OpenOCD and using QEMU User Mode Emulation for running
the big-endian binary on a little-endian host PC.
Change-Id: Ic5fe26e353a4cf69e57af3c23ae7fa4b25347b2b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6968
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The change 6363: Call poll at a fixed interval
switched from target_call_timer_callbacks() to target_call_timer_callbacks_now().
It breaks the timing as all timers callbacks are called every time
one timer expires.
Revert this part of change and use target_call_timer_callbacks().
Fixes: db16b3dc5b (Call poll at a fixed interval.)
Change-Id: Ib5b7774de9694d40c55d2a4109d0d1582fc5008b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7118
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While reviewing on gerrit the change
https://review.openocd.org/6932/
it get clear that the missing documentation on stm32f4x's code
was triggering errors in the new change.
OpenOCD is currently unable to read traces, but these can be
hopefully be read with some other tool.
Document the settings for enabling trace on stm32[fl]4x.
Change-Id: Ibae77a53de16375d3d500e728678740095547009
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6945
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu
code") the target's event "trace-config" has been deprecated.
Create the TPIU device.
Replace the target's event "trace-config" with tpiu's event
"pre-enable" in the STM32 devices that require enabling the trace
clock _before_ programming the TPIU.
Make the script multi-instance-able in case it's used for JTAG
chained devices.
Uniform the code in STM32F4x with the other scripts.
Remove the empty event from STM32WLx.
Change-Id: Ifda219c3c5f37e03072a88168611cf505eb630b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since commit 88f429ead0
5321: target/cortex_m: faster reading of all CPU registers
debugging with a kitprog adapter freezes at debug entry.
How to replicate:
openocd -f interface/kitprog.cfg -f target/psoc4.cfg
Connect to telnet server.
Make sure the target is running:
resume
Halt the target:
halt
Without this patch OpenOCD freezes in kitprog_hid_command()
in library call hid_write().
Reduce the number of SWD transactions sent in one USB bulk write
as a workaround, simply use shorter buffer.
For details see the comment in src/jtag/drivers/kitprog.c
Change-Id: I0116894d5ebf1655f6011f0d35acdbbc178cd48c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7107
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When printing memory sizes standard ISO 80000-1 prefixes should be used.
Also a space should be added between any number and its unit according
to papers publication rules.
Change-Id: Id1d35e210766b55c201de4e80ac165d8d0414d0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix Unused code Dead assignment at line 657
Fix Memory error Double free at line 2851
Fix Memory error Memory leak at line 2530
Fix error: 'a3' may be used uninitialized at line 758
Fix error: '%04x' directive writing between 4 and 8 bytes
into a region of size 5 at line 2471
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0382a622bc7c4108a335fd741816577e79240397
Reviewed-on: https://review.openocd.org/c/openocd/+/7137
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Change-Id: I9466edd2f43791e64f2dce719957c67728f3ec06
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Most adapters define their own commands to obtain the GPIO number and
other GPIO configuration information such as chip number, output drive
type, active high/low.
Define a general command 'adapter gpio' as replacement for the
driver-specific ones.
Change-Id: I1ca9ca94f0c7df5713172e9f62ffb0ad64e9ee97
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6967
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide a customizable hook for handling target-specific GDB queries
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I684a259ed29f3651cbce668101cff421e522f79e
Reviewed-on: https://review.openocd.org/c/openocd/+/7082
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'init' causes the execution of few lower level
commands, e.g. 'target init', and switches from command mode
COMMAND_CONFIG to COMMAND_EXEC, with an intermediate switch back
to mode COMMAND_CONFIG.
A timed target polling can occur during the execution of 'init'
and the target's status can trigger the execution of some events.
E.g. if a target has been left halted by a previous execution of
OpenOCD, the first poll will find the target halted, calling the
corresponding 'halted' event.
The event handler can use commands that can only be executed in
mode COMMAND_EXEC. If the poll happens while OpenOCD is in mode
COMMAND_CONFIG, the triggered handler will fail.
Prevent the target polling to operate during the execution of the
'init' command.
Change-Id: Ia435a5d2039be9b247e2336616dab53ed5d983ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7007
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB remote serial protocol specifies breakpoint/watchpoint packet
responses can be an empty string to indicate the specified breakpoint
type is not supported. Add support for this response alongside existing
"OK", "E NN" replies.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iaf6280e4c936eb95a92bc80cc74d451ebb328dc3
Reviewed-on: https://review.openocd.org/c/openocd/+/7102
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After a certain RTOS has been configured there is no mechanism
to go back to no RTOS support. It may be useful for debugging
purposes. With the provided modification, the "none" option
of RTOS is provided as a valid option.
It has been tested in two different board (Cortex M4 and Cortex M33).
Documentation has also been updated.
Signed-off-by: Asier Llano <allano@hubbell.com>
Change-Id: I602210bff31ccadd41c41e9454c52b5fffa1671e
Reviewed-on: https://review.openocd.org/c/openocd/+/7092
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
AARCH64_COMMON_MAGIC was same as CORTEX_A_COMMON_MAGIC, probably copy pasta.
Define unique AARCH64_COMMON_MAGIC
Change-Id: Ie30e0028453a1fce5624ecad9bf73d5ac3791281
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6997
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unify common_magic type to unsigned int
Move common_magic to be the first member of the struct
Add unsigned specifier to xxx_COMMON_MAGIC #defines
Change-Id: If961d33232698529514ba3720e04418baf6dc6fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6996
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The flash/nor subsystem uses bus_width and chip_width for CFI
external flash only. Drop setting these values for internal flash.
Change-Id: I64e79ab38b6e39e845ff96fbf4f60145e3b9690a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7098
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The working area allocation routines use 4 byte word alignment.
In the corner case the size of the working area is not aligned,
target_alloc_working_area() of size = target_get_working_area_avail()
will fail because the size gets aligned up and does not fit to the area
which size is aligned down.
Align down the result of target_get_working_area_avail() to cope with that
corner case.
While on it use fancy ALIGN_... macros instead of bitwise and operator.
Change-Id: Ia2a1e861c401c2c78fe6323379a3776fb4f47b06
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7096
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, if the target was halted before the FreeRTOS scheduler was
started but after at least one thread was created, then the current thread
would be set to whichever thread had the highest priority. In addition to
being misleading, because that thread is not actually running, it can
cause issues with gdb. For instance, breaking somewhere before the first
thread is created will show the current execution as the current thread,
but stepping over a line that creates a thread will cause the current
thread to switch to the newly created thread and the current execution to
disappear. The sudden disappearance of the current execution thread seems
to confuse some versions of gdb.
With this change, the value of xSchedulerRunning is checked to determine
whether the scheduler has been started. If it hasn't, then a fake
'current execution' thread is always created and made the current thread.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: Ide0fe7d9ffb9fac95cee4c805735f434c7c4934d
Reviewed-on: https://review.openocd.org/c/openocd/+/6935
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When there are no rtos threads or none are active, a fake thread with
ID 1 is created for the current execution, but the current thread ID was
never set to this new fake ID. This would lead to an incorrect attempt to
read stacked registers for this fake thread. Explicitly setting the
current thread ID to the fake ID ensures that the registers are read from
the core instead of calling freertos_get_thread_reg_list.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I694509a0e01df089429b20ff1b879fc0592b532d
Reviewed-on: https://review.openocd.org/c/openocd/+/6934
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We found that the NPCX has an issue with the byte lanes so that non byte
aligned writes aren't working. To overcome this, for byte accesses we
copy the byte to be written to all of the byte lanes.
doc: Document command nu_npcx_quirks
Signed-off-by: benjbender <benjbender@gmail.com>
[Andreas Fritiofson: Squashed commits]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I9ef63bf692f4e68f57459e1ec33f3abcbf533cd2
Reviewed-on: https://review.openocd.org/c/openocd/+/6630
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit b8e18d292e ("helper/jim-nvp: comply with coding style
[1/2]") tags as deprecated the old CamelCase API of jim-nvp, so
that old patches already in gerrit or in user's local git can
still build while dumping a deprecated message.
So far, we have not found any such case, so the deprecated API can
be safely dropped in preparation of v0.12.0-rc1.
Drop the compile flag "-Wno-error=deprecated-declarations" and the
deprecated API.
Change-Id: I52ce47eda69a51c2dd29aac15f16e285492d89b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7052
Tested-by: jenkins
With most of the files already processed through scripts, replace
manually the license to the few remaining files.
Change-Id: I3c7131e66b89ddad482f1074b5be5a9a69fdf6fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7073
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I30cd66ac7d737f1973c68fdbb841ffcf00e917c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7072
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: If0194089baded7f58dc5d87a35d6e0aff9f43785
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7070
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie873d12bb0fb838d0d6252e6b9ca3c2118853e9a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7069
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I7851617e2682f97ccc3927e3941aadef2df63b54
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7068
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ic7db91fe37d1139d42c99e303b3243b6c8fe3ea2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7067
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line in specific format.
Move the SPDX tag to the first line and fix it where needed.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie9a05f530009d482a4116eebd147fd7e1ee3d41e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7066
Tested-by: jenkins
Use the standard SPDX tag, where it was incorrectly applied.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Iaec63abc6e0a38e5b0ae0ea7f5ecee7ca007bbbd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7065
Tested-by: jenkins
Few files have the FSF boilerplate without the latest statement on
where to get the GPL license.
Manually replace the FSF boilerplate with the SPDX tag.
While there, reorganize the copyright statement.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I0c908d01c010e24f9c7e94885e7fbed4ecf26a86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7063
Tested-by: jenkins
Add the new license text in the license pool.
Replace the GPL and BSD boilerplates with the SPDX tag.
Add the copyright owner of Atmel, as it was explicitly listed in
the BSD boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ibb117dbf8402269be3e5ba4f4c472162494d813f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7062
Tested-by: jenkins
Add the license exception text in the license pool.
Add the exception chapter in license-rules.txt
Replace the boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ied513b7c9c0722ed2a9c11dbdff3fbf59f1b41ce
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7061
Tested-by: jenkins
Add the license text in the license pool.
Replace the BSD boilerplate with the SPDX tag.
Add the copyright owner of Jim Project, as it was explicitly
listed in the boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I6dd004b1945773c10539016ce733d1fbfe776a9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7060
Tested-by: jenkins
Replace the BSD boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I5a8cab2051eee7eb99adf67f9631b0827c1359de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7059
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I1fb51e722232d14f050458a820c3041de3dc9138
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7058
Tested-by: jenkins
SPDX tag is replacing the FSF boilerplate.
For files that have both, remove the FSF boilerplate and keep only
the SPDX tag.
Change-Id: I04c4764d13d4ca92453f30ed16aeae53cd4c3fc8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7057
Tested-by: jenkins
Add the SPDX tag to makefiles, configuration scripts and tcl files
present in the folders under src/
Change-Id: I1e4552aafe46ef4893d510da9d732c5f181784a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7051
Tested-by: jenkins
ARM/RISC-V semihosting calls SYS_READ/SYS_WRITE require
inversion of the result value as described in
"Semihosting for AArch32 and AArch64". Prior to
this patch, this was done correctly only if
(semihosting->is_fileio==false).
This patch has been tested with STM32F446.
Change-Id: I1b34c8d8393f7dfa66ee6539904a2eaf8f9154b0
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/232/
Reviewed-on: https://review.openocd.org/c/openocd/+/6803
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable 'smp_break' is only set and used in case of smp.
But clang cannot track if 'target->smp' get modified between the
set and the use of 'smp_break', so it consider possible to use
'smp_break' uninitialized.
Initialize 'smp_break' to silent clang.
Change-Id: Ifa25a84fe9ffa25b8b58d7920ec77994c3b7ebfe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 77287b8d47 ("target: add Espressif ESP32 basic support")
Reviewed-on: https://review.openocd.org/c/openocd/+/7050
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
These enum values are useful for the arch level semihosting call handlers.
Currently riscv uses them, we also need similar return codes for the xtensa.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I8f63749cc203c59b07862f33edf3c393cd7e33a9
Reviewed-on: https://review.openocd.org/c/openocd/+/7039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These are the misleading error messages that this change prevents:
configure.ac:13: error: possibly undefined macro: AC_MSG_WARN
If this token and others are legitimate, please use m4_pattern_allow.
See the Autoconf documentation.
configure.ac:48: error: possibly undefined macro: AC_DEFINE
configure.ac:342: error: possibly undefined macro: AC_MSG_ERROR
configure.ac:608: error: possibly undefined macro: AC_MSG_NOTICE
Change-Id: I21bcc7715eeac0f3d0bcc60bba6801e6a895cdd0
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7035
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
New mingw compiler correctly complains for using a freed memory
area:
src/helper/configuration.c: In function 'get_home_dir':
src/helper/configuration.c:182:29: error: dangling pointer 'home'
to 'homepath' may be used [-Werror=dangling-pointer=]
182 | home_path = alloc_printf("%s/%s", home, append_path);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In fact the variable 'homepath' is declared inside an 'if' branch
and is not available outside.
Move the declaration of 'homepath' to have it available in a wider
context.
Change-Id: I4a43a03c007c9f0d5c4cee962a9f7cc83ca49637
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Dietmar May <dietmar.may@outlook.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7038
Tested-by: jenkins
Reviewed-by: Dietmar May <dietmar.may@outlook.com>
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ief3da306a6e1978de7dfb8f552f9ff23151f9944
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7030
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/interface | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7bd6a628e9e153fc477cddf9b97087a39ec48aa7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7029
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/board | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ibcf7da62e842aafd036a78db9ea2b9f11f79af16
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7028
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line.
Change-Id: I3992856eeb28b333c38d010ef286e22471ede263
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7026
Tested-by: jenkins
Commit b9526f1401 ("semihosting: permit redirection of
semihosting I/O to TCP") introduces a new comparison with NULL.
Remove it.
Change-Id: Ice4333c50d16f7592f0ff86b1640217fa42e34f6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: b9526f1401 ("semihosting: permit redirection of semihosting I/O to TCP")
Reviewed-on: https://review.openocd.org/c/openocd/+/7031
Tested-by: jenkins
We already have a helper to release the gpio.
Extend it to also release its corresponding gpio chip.
As side effect, remove comparison with NULL.
Change-Id: I47cd446edfaead662d63c3330f25a791b747e882
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7033
Tested-by: jenkins
Reviewed-by: Steve Marple <stevemarple@googlemail.com>
Commit 6c0151623c ("aarch64: add support for "reset halt"")
introduces the register setting to halt at reset vector, but:
- does not consider the case 'srst_pulls_trst' that makes useless
setting the registers as they will be erased by the pulled trst;
- does not clean sticky errors in case of 'srst_gates_jtag'.
Avoid any register initialization on 'srst_pulls_trst' and move
the cleaning of sticky errors in the common block.
Change-Id: I6f839f06f7b091e234ede31ec18096e51f017bcd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 6c0151623c ("aarch64: add support for "reset halt"")
Reviewed-on: https://review.openocd.org/c/openocd/+/7034
Tested-by: jenkins
Reviewed-by: Christian Hoff <christian.hoff@advantest.com>
In order to facilitate debugging multiple cores, specify the coreid and
the hwthread rtos in the imx8m target configuration.
Change-Id: Ibd871517a160ceca15002fb10e27cb793f14d086
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-on: https://review.openocd.org/c/openocd/+/7019
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Custom user syscalls can be handled with target events in the TCL scripts.
This patch gives another opportunity to handle custom syscalls in the c files.
Besides that some utility functions are also exported for the custom handlers.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ice13d527540a0de0b2a8abda912ae3dcff3834b7
Reviewed-on: https://review.openocd.org/c/openocd/+/6889
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add Ampere Altra ("Quicksilver") and Ampere Altra Max ("Mystique")
target/board configuration files.
The target configuration file supports silicon and emulation.
The board configuration files support 1 and 2 socket platforms.
Tested on Ampere emulation and silicon
Change-Id: I036c798a50624e30ab51ccd2895b6f60c40be096
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5591
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Arm "CoreSight System-on-Chip SoC-600" specification describes a
bridge "Access Port v1 adapter" aimed to "connect a legacy Access
Port (AP) ... into an CoreSight Architecture v3 system".
A ROM table can be located in the "legacy" part of the system,
on the legacy AP behind the APv1 adapter.
For the purpose of scanning the ROM tables, consider an ADIv6
SoC-600 APv1 adapter as an ADIv5 AP.
Change-Id: I97d42fb77013c1251fb68d0caa4274086bf38a70
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6827
Tested-by: jenkins
Configuration file can specify, as target's debug AP, an AP that
contains a ROM table that points, in turn, to other APs.
Current code in cortex_a and aarch64 is not able to handle a
return from dap_lookup_cs_component() that points to another AP.
While it could be interesting to specify 'root' as target's debug
AP, drop any found value if it's not in the starting AP.
Change-Id: Id206e4fa7a29e9402c8e2393026817b410bbb8bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6826
Tested-by: jenkins
ADIv6 adds AP that only contain a ROM table in the AP itself, that
can point to other AP containing either another AP level ROM table
or a MEM-AP to be parsed as usual.
Add support for parsing AP level ROM tables.
Change-Id: Ic25863b16463b8a6adc3b15e26db7fdca858d6df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6467
Tested-by: jenkins
ADIv6 adds AP that only contain a ROM table in the AP itself, that
can point to other AP containing either another AP level ROM table
or a MEM-AP to be parsed as usual.
To handle recursive AP access, reorganize the code to:
- pass the depth==0 from the command 'dap info';
- print the AP number as first line, adding proper indentation on
depth>0;
- align the following print with proper indentation.
Change-Id: I5b811810c807fc51b307bd60f67817d9de2aa095
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6466
Tested-by: jenkins
On ADIv6 the system root ROM table is found by reading the DAP DP
registers BASEPTR0 and BASEPTR1.
Add option 'root' to the commands 'dap info' to let it retrieve
the system root ROM table's AP from DAP DP, then use such AP for
following dump.
Change-Id: I1789457a005faa3870c5d14f763378d2f6a5f095
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6462
Tested-by: jenkins
ADIv5 DAP can only have 256 AP, while ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
Reuse the field ap_num in struct adiv5_ap, currently used on ADIv5
to hold the ADIv5 AP number (apsel), to contain the ADIv6 AP base
address.
Convert struct adiv5_ap->ap_num to 64 bit and initialize it to
DP_APSEL_INVALID for unused AP.
Restrict dap_find_get_ap() to ADIv5 only. To be enhanced.
On ADIv6, let dap_get_ap() return an already allocated AP, or
allocate and return an unused AP.
Add function is_ap_num_valid() and use it.
Change-Id: Ib2fe8c7ec0d08393cd91c29fdac5d632dfc1e438
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6461
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
During enter in SWD read DP_DPIDR without selecting the register
bank through DP_SELECT_DPBANK.
Handle the different format of DP_SELECT register.
Change-Id: Iea1b8eb6ec94177e16a430d5885595a38e833eeb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6697
Tested-by: jenkins
ADIv5 reports:
Accessing AP registers or debug resources in connected
device through an AP can be subjected to other variable
response delays in the system. A debugger that can adapt
to these delays and avoid wasting WAIT scans operates more
efficiently and provides higher maximum data throughput.
The existing code in OpenOCD uses extra tck only for accessing
resources through an AP.
Extend the use of extra tck also for accessing an AP register.
Split from change https://review.openocd.org/6077/
Change-Id: I2082362e098d09f4ba0668e01f5196afc965c8f3
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6460
Tested-by: jenkins
By accessing invalid AP in JTAG mode, it's possible to trigger the
error:
JTAG-DP STICKY ERROR
After that the sticky error is never cleared and the whole DAP
gets not anymore accessible.
Clean-up the sticky error once detected.
Change-Id: I8b07263b30f9e46645f0c29084b8f1626e241f45
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6430
Tested-by: jenkins
ADIv5 MEM-AP registers are a subset of ADIv6 MEM-AP registers and
are located at different offset.
To prepare for introducing ADIv6, add 'struct adiv5_dap *' as
argument to ADIv5 registers macro.
Check the ADI version and use the proper address.
Both adapter drivers rshim and stlink are ADIv5 only, so let them
use the ADIv5 macros only.
Split from change https://review.openocd.org/6077/
Change-Id: Ib861ddcdab74637b2082cc9f2612dea0007d77b1
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6457
Tested-by: jenkins
While an ADIv5 DAP can only have 256 AP, ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
The actual trivial code implementation for ADIv5 (that uses an
array of 256 ap in the struct adiv5_dap) cannot be extended as-is
to handle ADIv6.
The simple array of 256 AP can be reused as a dynamic storage for
ADIv6 ap:
- the ADIv5 AP number is replaced by the ADIv6 base address;
- the index of the array (equal to ADIv5 AP number) has no link to
any ADIv6 property;
- the ADIv6 base_address has to be searched in the array of AP.
The 256 elements in the AP array should be enough for any device
available today. In future it can be easily increased, if needed.
To efficiently use the 256 elements in the AP array, the code
should associate one element of the array to an ADIv6 AP (through
the AP base address), then cancel the association when the AP is
not anymore needed. This is important to avoid saturating the AP
array while exploring the device through 'dap apreg' commands.
Add a reference counter in the struct adiv5_ap to track how many
times the struct has been associated with the same base address.
Introduce the function dap_get_ap() to associate and return the
struct, and dap_put_ap() to release the struct. For the moment the
code covers ADIv5 only, so the association is through the index.
Use the two functions above and dap_find_get_ap() throughout the
code.
Check the return value of dap_get_ap(). It is always not NULL in
the current ADIv5-only implementation, but can be NULL for ADIv6
when there are no more available AP in the array.
Instrument dap_queue_ap_read() and dap_queue_ap_write() to log an
error message if the AP has reference counter zero, meaning that
the AP has not been 'get' yet. This helps identifying AP used
without get/put, e.g. code missed by this patch, or merged later.
Instrument dap_cleanup_all() to log an error message if an AP has
reference counter not zero at openocd exit, meaning that the AP
has not been 'put' yet.
Change-Id: I98316eb42b9f3d9c9bbbb6c73b1091b53f629092
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6455
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
The array is partially initialized with buf_set_u32(,5,32,), then
the rest of the array is read from SWD.
But scan-build report the array to have garbage content after the
initialization, due to the offset of 5 bit that only inits part of
the first byte.
Silence the false positive from scan-build by initializing the
array.
Change-Id: Ic38d50280f67939e3ec5fa05741f66d5f993f8c2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7013
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While scan-build complains that dap_p or ap_num_p could be NULL,
the current code never passes NULL pointers.
Add an assert() to silent scan-build and prevent any further use
of the function with incorrect parameters.
Change-Id: I656810dddcea61e85d85b13efb114f7607ef837c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7012
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit d01b3d69ec ("arm_adi_v5: separate ROM table parsing from
command output [3/3]") introduces a new scan-build warning because
removing one return in case of error causes using uninitialized
values.
Add back the return on error.
Change-Id: I10ddc548b756d34aaccc0511f091b4caa5ec271a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: d01b3d69ec ("arm_adi_v5: separate ROM table parsing from command output [3/3]")
Reviewed-on: https://review.openocd.org/c/openocd/+/7011
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 21f7885d1c ("arm_adi_v5: separate ROM table parsing from
command output [1/3]") introduces a new scan-build warning because
continues the execution even when dap_get_debugbase() returns
error. The value of 'apid' can be uninitialized:
5th function call argument is an uninitialized value
Check the return value and quit on error.
While there, remove the useless initialization of 'dbgbase' that
was apparently required for the same problem.
Change-Id: Iade26a152925ee0f1bf114ed829b94f7ed5b254f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 21f7885d1c ("arm_adi_v5: separate ROM table parsing from command output [1/3]")
Reviewed-on: https://review.openocd.org/c/openocd/+/7010
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target_to_armv7m() just returns a type-cast of target->arch_info,
so the test has no value.
Following target_run_algorithm() checks magic number so
we need not worry about execution on mismatched architecture.
Change-Id: Ic9892a488a42af1d8e8731eddb39240deeb26020
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6755
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Error: Uninitialised value was created by a heap allocation
at telnet_new_connection (telnet_server.c:227)
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I698a3648be698c93a2395a718ee1ade028226995
Reviewed-on: https://review.openocd.org/c/openocd/+/7006
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix "Declared variable-length array (VLA) has zero size" warnings
while at there instrument the probe function to ensure the flash bank
contains at least 1 sector
Change-Id: I3ba0e6345881557ad1aab2d1b41eee438b49fe04
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6470
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'flash erase_check' showed the message
'Running slow fallback erase check - add working memory'
even in the case the target didn't implement blank_check_memory.
Change return code of target_blank_check_memory() in this case
and sense it in default_flash_blank_check() and show a message
without a request for working memory.
Change-Id: I7cf9bf77742964b4f377c9ce48ca689e57d0882f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6765
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
This helps e.g. if there are 8 cores, and cores 0--3 are in one SMP
group while 4--7 are in another group. (And there are 2 gdb instances
connected, one debugging the first group, and one the second.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7b6c9382eadf964529105eaf0411a42d48768668
Reviewed-on: https://review.openocd.org/c/openocd/+/6979
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1028A is similar to the LS1088A, except that it has 2 CPUs (and
different ethernet capabilities). From a JTAG perspective, all that's
different is the number of CPUs and the TAPID.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Iba3a0ecfbf82cfcfeb7eea42d52121c3b9dc93a2
Reviewed-on: https://review.openocd.org/c/openocd/+/6976
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Several Layerscape processors (LS1088A, LS2088A, LS2160A, and LS1028A)
share a common architecture. Break out the common setup from the LS1088
config in preparation for adding the LS1028A. There's no official name
for this series of processors, but NXP refers to them as "chassis
generation 3" in U-Boot, so we'll go with that too.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ic6f89f95c678101f54579bcaa5d79c5b67ddf50a
Reviewed-on: https://review.openocd.org/c/openocd/+/6975
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removes Warning: line 6482, column 12
1st function call argument is an uninitialized value
Use target ptr directly as checked in previous lines instead of
dereferencing head->target
Change-Id: I6804b776fd493af71f3098d702f9cdc7acb50151
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6970
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
First time contributors surprisingly often write "topic:"
instead of "the main part or subsystem the patch touches" as requested
in patchguide.html
To prevent them doing so:
Use longer self-explaing "specify touched area" instead of "topic"
Give some examples in addition to recommended looking at "git log"
Change-Id: I1c307b460d7a79ba3c9918af8dbc9e9f827e1fb9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6683
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tigard[1] is an FT2232H-based development tool designed for ease of use
with many different protocols and targets. It includes a JTAG header
wired to channel B, with labeled pins for the four required signals as
well as nTRST and nSRST, which are connected through an output buffer to
BDBUS4 and BDBUS5 respectively.
Add an interface config for Tigard. I wrote it by referencing the Tigard
schematic and tested it by debugging a couple of RISC-V development
boards.
[1] https://github.com/tigard-tools/tigard
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Change-Id: I34df9f72538ba1e40ad53b568c9cdca96ae4b082
Reviewed-on: https://review.openocd.org/c/openocd/+/6952
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While cross-compiling OpenOCD the generated script is not named
"libtool" anymore, but e.g. "arm-linux-gnueabi-libtool".
Ignore all the possible variants "*-libtool".
Change-Id: I7a0dade992dbc13f977610bd4a78f8a4783b0146
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6960
Tested-by: jenkins
Incorrect validation prevented GPIO0 from controlling the direction of
the SWDIO buffer or operating TRST/SRST.
Have all GPIO number validation checks performed by is_gpio_valid().
Change-Id: Ib8fb704ab588a618ac41c111f6168d658891d92c
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It is a common requirement to automatically execute some command
after "init".
This can be achieved, either in scripts or through OpenOCD command
line, by explicitly calling "init" followed by the commands.
But this approach fails if the request for post-init commands is
spread across configuration files; only one of the files can split
pre-init and post-init status by calling "init".
The common workaround is to "rename" the command "init" and
replace it with a TCL proc that calls the original "init" and the
post-init commands. E.g. in Zephyr script [1].
To simplify and formalize the post-init execution, use a TCL list
that contains the list of commands to be executed. Every script
can contribute adding new commands, e.g. using "lappend".
In the same way, formalize the pre-shutdown execution with a TCL
list of user commands to be executed before OpenOCD exit.
Document them and add trivial examples.
Drop from documentation the suggestion to rename "shutdown".
Change-Id: I9464fb40ccede3e7760d425873adca363b49a64f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Link: [1] https://github.com/zephyrproject-rtos/zephyr/blob/zephyr-v2.7.1/boards/arm/nucleo_h743zi/support/openocd.cfg#L15
Reviewed-on: https://review.openocd.org/c/openocd/+/6851
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function target_type::deassert_reset() is called for every
target after reset is deasserted. If the target fails to get
halted, we log a warning and issue a halt request for the target
itself.
Current code calls the generic target_halt() that:
- extends the halt to all the targets in the SMP node;
- waits for targets to halt.
This breaks the logic of running target_type::deassert_reset()
per target. Plus, waiting for targets to halt delays the call of
target_type::deassert_reset() for the next targets.
Replace the call to target_halt() with the aarch64 specific
function to halt the single target. Pass the parameter HALT_LAZY
to prevent the wait for target halted.
Similar solution is already implemented for cortex_a.
Change-Id: I446dc03cb91524c6d388db485bc2388177af77b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6947
Tested-by: jenkins
Arm documentation does not explicitly report the order of the two
32bit words that compose the 64bit value. But both ADIv5 and ADIv6
specify that only little-endian is supported (ADIv5.2 obsoletes
the big-endian support). This change reads the 64bit value in
little-endian.
Detect the 64bit content and use it.
Change-Id: I723ec099c7e8c70c1f9a568e32ea867fcbf1f1db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6465
Tested-by: jenkins
With the generic function for ROM table walk-through, reimplement
dap_lookup_cs_component().
Catch the code CORESIGHT_COMPONENT_FOUND and halt the search.
While there, drop two macros in arm_coresight.h, now unused.
Change-Id: I589ef7ae8a651d0c422ce7d0b4ed913713a8217e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6824
Tested-by: jenkins
Simplify the code in cortex_a and aarch64 by moving the call to
dap_get_debugbase() inside dap_lookup_cs_component().
This has the further effects:
- dap_get_debugbase() is not referenced outside arm_adi_v5.c and
becomes static;
- dap_lookup_cs_component() looses one parameter;
- the coreid parameter 'idx' is passed as value;
- the caller in aarch64 don't have and don't print the irrelevant
value of AP register APID;
- fixes the debug message in the caller in aarch64 to print the
coreid value instead of always zero.
Change-Id: Ic7f0f643fdf067c059c8f2455a02ff18a3fed054
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6823
Tested-by: jenkins
Now all the actions (build command output) of command "dap info"
are decoupled from the ROM walk-through.
Pass the actions as a generic parameter to ROM walk-through code.
Put as private data every information that is only required by the
actions and not by the ROM walk-through.
Change-Id: I3b6ad112ea21296458c94aebbf91bf65bf6657a7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6822
Tested-by: jenkins
This change only targets the output of rtp_cs_component().
To easily propagate the coordinates of the CoreSight component,
add them in the struct that holds the register values.
While there, define a macro for the max depth of ROM tables.
Change-Id: I75e5ef4f9419da3192123aebcd61471c2af9374f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6820
Tested-by: jenkins
In OpenOCD arm_adi_v5 we have already two implementations of code
for parsing the ADIv5 ROM table:
- in the commands "dap info" and "$dap_name info";
- in the function dap_lookup_cs_component().
Adding support for ADIv6 requires extending both implementations.
Moreover, current code does not handle few aspects of the ROM
parsing, e.g. the "Power Domain IDs".
To add such extensions both implementations should be touched.
I plan to add a command to parses (again) the ROM table and dump a
simple prototype of a configuration script for the target, useful
while analysing a new target.
Keeping aligned all these implementation would be too complex.
With focus to "dap info" command, decouple the part of code to
walk-through the ROM table from the code that creates the command
output.
The idea is to keep a single implementation for the walk-through
code, while parametrizing the output code to handle the generation
of a configuration script or the result of the function
dap_lookup_cs_component().
This change only targets the output of MEM-AP header
Further changes will target other parts of the code.
While there, add a message if MEM-AP is not accessible.
Change-Id: I112f637edfdb8688afb4e631297f6536da9604f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6819
Tested-by: jenkins
ARM IHI0031F "Arm Debug Interface Architecture Specification"
chapter C2.6.1 "BASE, Debug Base Address register" reports:
A debugger must handle the following situations as
non-fatal errors:
- ...
- An entry in the ROM Table points to a faulting location.
- ...
Typically, a debugger issues a warning if it encounters
one of these situations. However, Arm recommends that it
continues operating. An example of an implementation that
might cause errors of this type is a system with static
base address or ROM Table entries that enable entire
subsystems to be disabled, for example by a tie-off input,
packaging choice, fuse, or similar.
Don't halt ROM table parsing if one entry causes an error; log the
error condition and continue to next entry.
Not sure if we have to send an ABORT before continuing.
Change-Id: I94fdb5b175bfb07dde378149421582b7e7cd5b09
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6818
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
As Class 0x1 ROM table, also Class 0x9 ROM tables encodes a flag
for system memory access.
Detect the flag in rtp_cs_component() and dump the same message
for both type of ROM tables.
Extend rtp_read_cs_regs() to read ARM_CS_C9_DEVID.
Change-Id: Ic85d1ea068ed706ceedfd65076ff4c96d04e9792
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6817
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
During ROM table parsing, each ROM table entry points to a
CoreSight component that can, in turn, be another ROM table.
Split the specific code for ROM table handling from the generic
CoreSight code.
Log an error if a ROM table entry cannot be read.
Change-Id: I5ad106a99b9c21ddb48b5b162ae87101e4f49878
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6816
Tested-by: jenkins
Rework dap_read_part_id() while preparing for reorganizing the
'ROM Table Parsing' (RTP):
- rename it with 'rtp' prefix;
- extends it to read other CoreSight registers, thus improving the
overall speed by queuing more reads;
- reduce the list of arguments by using a struct;
- reorder the reads by increasing offset, potentially gaining
speed using MEM_AP_REG_BDx and/or auto-increment;
- log a debug message in case of read error.
Change-Id: I6544ac7740b808a6c0fbacf97ac00b97f5bd3832
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6815
Tested-by: jenkins
ADI v5.1 and v6.0 permit the definition of CoreSight components (class 9
ROM entries).
dap_rom_display() is refactored a bit such that we always end up with
attempting to parse the ROM contents using the appropriate upper limit
for class 1 and 9 ROM types.
Change-Id: I4ba497b3807f1f11f06186eb6e61959ea3540c59
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6359
Tested-by: jenkins
Use the list of values from ARM IHI0029E to decode and print the
Device Architecture register.
Add attribute 'unused' to the function, not used yet.
Change-Id: I7b1dd204bd1db671578c588372b667e23611876c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6463
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
In case of AP not responding, e.g. not clocked, the first WAIT
reply is logged as:
DAP transaction stalled (WAIT) - slowing down
then OpenOCD retries the transaction few times, until it timeouts.
At each retry it prints the message:
DAP transaction stalled during replay (WAIT) - resending
Depending on JTAG speed and transport latency, the amount of log
messages can be quite annoying and not relevant.
The last printed line is at timeout:
Timeout during WAIT recovery
Reduce the verbosity.
Change-Id: I5a7a337527c98b2450de59066b13713511c2894f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6814
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
In jimtcl 0.80 the prototype of Jim_DictPairs() has changed.
The only code in OpenOCD that uses Jim_DictPairs() has been merged
recently and it only uses the current jimtcl syntax.
To allow compiling OpenOCD master branch with older versions of
jimtcl, detect the version of jimtcl and use the appropriate
syntax.
Change-Id: I6fc78303b6a4db064a97f326c46119f4568e88f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: dullfire@yahoo.com
Reviewed-on: https://review.openocd.org/c/openocd/+/6948
Tested-by: jenkins
Added bluenrg-lps support
Added file for the board steval-idb012v1
Fixed size_info information using a mask
Changed the if condition in bluenrg-x.cfg to be valid only for bluenrg-1 and bluenrg-2
Signed-off-by: Salvatore Giorgio PECORINO <salvatore-giorgio.pecorino@st.com>
Change-Id: Ic0777ec0811ee6fac7d5e1d065c4629e47d84a1f
Reviewed-on: https://review.openocd.org/c/openocd/+/6928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 5ebb1bdea1 ("server/gdb: fix return of gdb remote monitor
command") replaces the call to command_run_line() with call to
Jim_EvalObj() but does not properly set the "context".
In multi-target environment, his can cause the erroneously
execution of the command on the wrong target.
Copy from the code in command_run_line() the proper setup before
executing Jim_EvalObj().
Change-Id: I56738c80779082ca146a06c01bc30e28bc835fd3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Bohdan Tymkiv <bohdan200@gmail.com>
Fixes: 5ebb1bdea1 ("server/gdb: fix return of gdb remote monitor command")
Reviewed-on: https://review.openocd.org/c/openocd/+/6966
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
The deprecation was already in the documentation since v0.11.0
through commit 85ba2dc4c6 ("rtos/hwthread: add hardware-thread
pseudo rtos") but OpenOCD was not informing the user printing a
runtime message.
Remove the deprecated method from the documentation and print a
deprecated message at runtime.
There is no reliable way to print the same message in GDB console,
so we have to rely on user noticing it in the OpenOCD log.
Target is to remove the functionality after v0.12.0.
Change-Id: Idd2d9e3b6eccc92dcf0432c3c7de2f8a0fcabe9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6862
Tested-by: jenkins
on macos (homebrew base) `pkg-config --cflags capstone` output with
`-I/opt/homebrew/Cellar/capstone/4.0.2/include/capstone`
gcc not find headers on parent "include" path,
causes build error `fatal error: 'capstone/capstone.h' file not found`
it's ok to change to <capstone.h> for all platforms.
Signed-off-by: fatalc <cnfatal@gmail.com>
Change-Id: Ia2e2058024d4fc1a57a8b4ea847c664d74f67efb
Reviewed-on: https://review.openocd.org/c/openocd/+/6946
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Handle JIM_CONTINUE return value of adiv5_jim_mem_ap_spot_configure(),
otherwise OpenOCD silently quits when an unknown option is provided.
Change-Id: I9b1351c0911e74999d8dd1260ede9760088510d7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6944
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The SWDIO buffer requires a direction pin to select input or output
direction. Output is selected by a high logic level (matches
bcm2835gpio driver).
Change-Id: I240cb99a5dfea08121bb33d4b5e2108ce7597468
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to GigaDevice user manuals the devices have OBRLD bit in FMC_CTL
register which is functionally compatible with OBL_LAUNCH @ FLASH_CR
of STM32 counterparts.
Change-Id: I84d231b38815fcb6452fd73b9153b269cce3b737
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6759
Tested-by: jenkins
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
The flash is compatible with stm32f1x, reuse the driver.
Extend the size of work area to RAM size of the smallest device.
Stop watchdogs before flash programming.
Change-Id: I67a7654a6e196f9d4b2409edaa7990c53334437e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6711
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The device has compatible flash macro with STM32F1 family, reuse
stm32f1x driver code.
Detect non-ARM target - for simplicy test target type name 'riscv'
and the address has 32 bits.
In case of RISC-V CPU use simple chunked write algo - async algo
cannot be used as the core implemented in this device doesn't
allow memory access while running.
Change-Id: Ie3886fbd8573652691f91a02335812a7300689f7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6704
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Zephyr plan to remove openocd specific symbols in favour
of more generic one.
These generic symbols has been introduced in Zephyr 2.6.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: I89418c9c378fb8b8baa29763fc6f1b6e652dc7ef
Reviewed-on: https://review.openocd.org/c/openocd/+/6844
Tested-by: jenkins
Reviewed-by: Stephanos Ioannidis <root@stephanos.io>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Current implementation for gdb remote monitor command uses the
command_run_line() to execute the command.
While command_run_line() has several advantages, it unfortunately
hides the error codes and outputs the result of the command
through LOG_USER(), which is not what gdb requires. See 'qRcmd' in
https://sourceware.org/gdb/onlinedocs/gdb/General-Query-Packets.html
Replace command_run_line() with Jim_EvalObj() and parse the output
to provide the proper result to gdb.
Can be tested by defining in OpenOCD:
proc a {} {return hello}
proc b {} {return -code 4}
proc c {} {return -code 4 "This is an error!"}
then by executing in gdb console:
monitor a
monitor b
monitor c
monitor foo
Change-Id: I1b85554d59221560e97861a499e16764e70c1172
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Torbjorn Svensson <torbjorn.svensson@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6886
Tested-by: jenkins
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
Deprecate both nds32 target and aice adapter with the target of
dropping them for v0.13.0.
Remove automatic build of aice, forcing user to select it.
Change-Id: Ib465d676246fa3b4e95c3d399ba9a5cf1f8b3baf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The current code locks the flash controller in case of error during
flash write only. An error in other flash operations may cause the
flash is left unlocked.
Implement locking also after error in erase, mass erase, options
write and erase.
Change-Id: I26c2ed7914e7847122306f29b777b9eefd1dc580
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6710
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
stm32x_wait_status_busy() has two side effects in case of flash programming error:
- reports error
- clears error bit in status register
Use stm32x_wait_status_busy() to report also flash error during target
algo flash write.
While on it use more descriptive error codes in stm32x_wait_status_busy().
Change-Id: I6e1cffc2aa5411b918a23ed62d5194910888a9d1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6709
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Use target_get_working_area_avail() instead of try-fail iteration.
Call destroy_reg_param() in a for cycle.
Change-Id: I1891d1ffdea99010c6ab66b9578400b9d7922e20
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6708
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Mostly refactoring.
Rename original stm32x_write_block() to stm32x_write_block_async()
as it uses target async algo.
Introduce new stm32x_write_block() and move slow, host controlled
fallback flash write there.
The change allows stm32x_write_options() to use slow flash write fallback.
While on it rename variables where halfword count is stored.
Change-Id: I386ae15cf052b1490461ed8f7eea5b4403d466f7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6706
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
When we debug a target that works as a USB device, halting
the target causes the USB communication with the USB host to
become unresponsive. The host will try to reconnect/reset/setup
the unresponsive device during which communication with other
devices on the same USB bus can get stalled for several seconds.
If the JTAG adapter is on the same bus, we need to make sure
openOCD will wait for packets at least as long as the host USB
stack. Otherwise the USB stack might deliver a valid packet, but
openOCD would ignore it due to the timeout. The xHCI spec uses 5
sec timeouts, so let's use that in openOCD with some margin.
Use this value in all libusb calls. HID API might have a libusb
backend and would probably be victim to the same bug, so it
should use this timeout, too.
Ticket: https://sourceforge.net/p/openocd/tickets/343/
Signed-off-by: Gabor Csapo <gaborcsapo@google.com>
Change-Id: Ia3dc1356e676fe550f57a4c72f7a24ba296b6af2
Reviewed-on: https://review.openocd.org/c/openocd/+/6882
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Print also the target name, not just the packet contents.
This is important when there are more GDB servers (more
debug-able targets) active in one OpenOCD session.
- Log also the received Ctrl-C requests coming from GDB
(one byte 0x3), ACKs ("+") and NACKs ("-").
- Do not print zero-length incoming packets (this occurred
when Ctrl-C packets were received).
- Removed a stray apostrophe "'" that got printed
in gdb_log_outgoing_packet()
Signed-off-by: Jan Matyas <matyas@codasip.com>
Change-Id: If68fe0a8aa635165d0bbe6fa0e48a4645a02da67
Reviewed-on: https://review.openocd.org/c/openocd/+/6879
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To support 64 bits bit and masks
Replace local definition of BIT in rtos/chromium-ec
Change-Id: I1f268d6e8790f1b07bf798680b797878ce81064b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6857
Tested-by: jenkins
Including config.h as first is required for every C file.
Add it to the C files that still miss it.
Change-Id: I1a210e7d3a854958a85a290b086ad8a9f5176425
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6856
Tested-by: jenkins
While the documentation reports that SWO pin frequency can be
omitted to let the adapter autodetect the value, the code wrongly
drops an error when pin frequency is not specified.
Don't require the pin frequency to be set at "enable", but verify
that the adapter has properly changes it to a valid value.
Change-Id: I3dfbe3256e8887ef4f03512769b06381cdc9db0d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Karl Palsson <karlp@tweak.net.au>
Fixes: 184724d14e ("arm_tpiu_swo: add support for independent TPIU and SWO")
Reviewed-on: https://review.openocd.org/c/openocd/+/6310
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Commit dbbac5f11d ("semihosting: use open mode flags from GDB,
not from sys/stat.h") fixes the conversion of the mode flags from
ARM semihosting encoding for SEMIHOSTING_SYS_OPEN to GDB mapping
for open().
Doing this, it breaks the conversion to local host's OS mapping
for open().
Split the conversion array to one for GDB and one for local host.
The local host conversion array is taken directly from the old
code.
Change-Id: I385321ddd32c3ac5cf6da3f1ce9eff76b05dd527
Fixes: dbbac5f11d ("semihosting: use open mode flags from GDB, not from sys/stat.h")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6870
Tested-by: jenkins
Some configuration of GCC could default to -fno-inline, causing
the build to fail after commit fb43f1ff4e ("target: Rework 'set'
variable of break-/watchpoints").
Switch the new inline functions to 'static inline', as it's widely
used in the rest of the code.
Change-Id: I8bf31045a137bd34ed825f4b2a9338eb3c70046d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fb43f1ff4e ("target: Rework 'set' variable of break-/watchpoints")
Reviewed-on: https://review.openocd.org/c/openocd/+/6881
Tested-by: jenkins
The 'set' variable name suggests a boolean data type which determines
whether a breakpoint (or watchpoint) is active. However, it is also
used to store the number of the breakpoint.
This encoding leads to inconsistent value assignments: boolean and
integer values are mixed. Also, associated hardware comparator
numbers, which are usually numbered from 0, cannot be used directly.
An additional offset is required to store the comparator numbers.
In order to make the code more readable and the value assignment more
consistent, change the variable name to 'is_set', its data type to 'bool'
and introduce a dedicated variable for the break-/watchpoint
number.
In order to make the review easier, the data types of various related
variables (e.g. number of breakpoints) are not changed.
While at it, fix a few coding style issues.
Change-Id: I2193f5639247cce6b80580d4c1c6afee916aeb82
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6319
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Considering this use case: (using STM32 L5 or U5)
1- first probe : TZEN enabled, RDP level 0
flash_regs_base |= STM32L5_REGS_SEC_OFFSET => 0x50022000
2- the user promotes the RDP to level 0.5
3- the second probe, fails to read OPTR using secure flags_regs_base:
used OPTR address is 0x50022040
Step 3 fails because when RDP is level 0.5, we should use Non-Secure
flash registers.
To fix this, always use NS flash regs to read OPTR in probe functions.
Fixes: 80d323c6e8 (flash/stm32l4x: introduce auto-probe when OPTR is changed)
Change-Id: I296aa633972b0c410b927488c999584a07b912d3
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6864
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
ST-Link Server 2.1.0-1 fixes concurrency issue with RW_MISC command
Starting from this version the ST-Link Server API is now v3.
In this change we save the ST-Link Server version, and check if the
API is greater or equal to 3 to enable the queuing.
Change-Id: I239eb81024700514c607a269b66651f457206faa
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6876
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This command permits the usage of a TCP port to perform debug and stdio
operations:
- debug : READC, WRITEC and WRITE0
- stdio : READ, WRITE
This will permit the separation of semihosting message from OpenOCD log,
and separate semihosting messages per core.
syntax: arm semihosting_redirect (disable | tcp <port> [debug|stdio|all])
this allows to select which operations to be performed via TCP (debug,
stdio or all (default)).
Note: for stdio operations, only I/O from/to ':tt' file descriptors are
redirected.
tested using netcat on ubuntu
Change-Id: I37053463667ba109d52429d4f98bc98d0ede298d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5562
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD implements the GDB keep-alive by sending empty strings as
output for GDB client. This has been implemented as part of the
log framework, creating an odd dependency.
Move the keep-alive notifications out of log framework.
For the moment, keep keep_alive() inside log.c, but it should be
moved in server.c
This should also fix an old issue with KDE Konsole when tab alert
for activity is enabled. The empty strings is sent to all the
connections, including telnet, and causes the tab running OpenOCD
telnet to continuously show activity even when no new text is
printed. Anyway, I cannot replicate this issue anymore.
Change-Id: Iebb00b00fb74b3c9665d9e1ddd3c055275bfbd43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6840
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB client cannot always display generic messages from OpenOCD.
The callback gdb_log_callback() is continuously added and removed
to follow the GDB status and thus enabling/disabling sending the
OpenOCD output to GDB.
While this is a nice stress test for log_{add,remove}_callback(),
it is also a waste of computational resources that could impact
the speed of OpenOCD during GDB user interactions.
Add a connection-level flag to enable/disable the log callback and
simply change the flag instead of adding/removing the callback.
Use an enum for the flag instead of a bool. This improves code
readability and allows setting other states, e.g. keep-alive
through asynchronous notification https://review.openocd.org/4828/
Change-Id: I072d3c6928dedfd0cef0abe7acf9bdd4b89dbf5b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6839
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
To easily add new methods to a service, pass all the methods
through a struct.
While there, drop the typedef for the methods and add currently
unused new methods to support keep-alive and connections during
keep-alive.
No change in functionality.
Change-Id: I2b5e7140db95021f6e7201e9d631ee340c60b453
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6838
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The kept_alive() action is specific of a server that enjoyed an
unscheduled keep_alive and want to communicate it to the keep
alive logic to reschedule next keep_alive().
In server loop we are not expected to call kept_alive().
Remove it!
This call was erroneously added in commit 94e75e0c06.
Later, commit 7442b26d45 properly added the same call in
gdb_put_packet(), but incorrectly left the older in place.
Change-Id: If476410f870eebfbdaccdb1366ba2e9254e2fdf6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6836
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Replace deprecated commands 'mem2array' and 'array2mem' with
new Tcl commands 'read_memory' and 'write_memory'.
Change-Id: I116d995995396133ca782b14cce02bd1ab917a4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6859
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace 'mem2array' and 'array2mem' with a Tcl wrapper that
internally uses 'read_memory' and 'write_memory'.
The target-specific 'mem2array' and 'array2mem' functions
remain for now.
Change-Id: If24c22a76ac72d4c26916a95f7f17902b41b6d9e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6308
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These functions are meant as replacement for 'mem2array' and
'array2mem'.
The main benefits of these new functions are:
* They do not use Tcl arrays but lists which makes it easier
to parse (generate) the data. See the Python Tcl RPC code
in contrib as a negative example.
* They do not operate on Tcl variables but instead return (accept)
the Tcl list directly. This makes the C and Tcl code base
smaller and cleaner.
* The code is slightly more performant when reading / writing
large amount of data. Tested with a simple Python Tcl RPC
benchmark.
Change-Id: Ibd6ece3360c0d002abaadc37f078b10a8bb606f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When jimtcl is built in maintainer mode, it runs extra tests at
exit to look for memory leak due to jim objects not properly freed
either through Jim_IncrRefCount()/Jim_DecrRefCount() or by passing
it to a jim API.
Add optional OpenOCD configure flag '--enable-jimtcl-maintainer'
to enable jimtcl maintainer mode.
Modify the implementation of macro AX_CONFIG_SUBDIR_OPTION to
allow expanding a variable passed as second argument.
Change-Id: Id1a39b25cee3773b172faf70803fa150182f0cd6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6871
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
This adds support for the LS1046A Reference Design Board. There are
several JTAG headers accessable once the case is opened, but this config
is for the externally-accessable CMSIS DAP.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I0f83470da3758f0c4512ce47348c4db7de17b27e
Reviewed-on: https://review.openocd.org/c/openocd/+/6855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1046A is a quad-core processor from NXP in the layerscape family.
This SoC is a bit tricky to program: while the AArch64 CPUs are
little-endian, most of the peripherals are big-endian. Care must be
taken when interpreting memory reads/writes. This processor is in the
same family as the ls1012a, so the setup is similar.
If you use OpenOCD to attach early in the boot process, only the cpu0
may be available. Trying to halt other CPUs will fail. To avoid this,
defer examination of cpus 1-3, and provide a core_up helper (like e.g.
zynqmp).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: If5a1a9441fb35fea3e05dc708b42e0cb3bbf2a54
Reviewed-on: https://review.openocd.org/c/openocd/+/6854
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32H7Ax/7Bx devices have a different WPSN mask (0xFFFFFFFF),
(0xFF for STM32H74x/75x and STM32H72x/73x devices).
And when supporting STM32H7Ax/7Bx devices, stm32x_protect() was
not updated accordingly.
Change-Id: I081217af3e5ed815b67bfdfec7f4ebaa3152a865
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Fixes: 0b7eca1769 (flash/stm32h7x: add support of STM32H7Ax/H7Bx devices)
Reviewed-on: https://review.openocd.org/c/openocd/+/6858
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Multiple smaller items addressed in jtag_vpi:
- Several log prints adjusted to make them more clear to the user.
- Ensured that command handlers return ERROR_COMMAND_SYNTAX_ERROR
on incorrect number of arguments.
- Fix in "jtag_vpi set_address": Leave the previously set address
intact on error. Do not revert it to default.
- Minor update of help messages for the TCL commands.
- Updated macro names: SERVER_ADDRESS --> DEFAULT_SERVER_ADDRESS,
the same for SERVER_PORT
Change-Id: Ibe386403a179adab5edb69c77fa408aef55701bd
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6845
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Original TLC syntax uses 'set varname' to retrieve the value of
variable 'varname'. Such archaic syntax is still valid, but the
shorter '$varname' makes the code easier to read.
Replace 'set varname' with '$varname'.
While there, remove some useless curly brackets.
Change-Id: I27310e8c05afe56ea8bd0e41d4ae2c34447b725c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6863
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since we can detect the type of target as well, reuse the _cpu_no_smp_up
function name and use the target name to simplify the _up function and
maintain consistency with what we introduced for r5.
Lets introduce gdb-attach event in a much cleaner fashion.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
While at it, fix a minor type of s/are/as in "Set Default target are
core 0" and simplify the foreach usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3259b7c3ae4c71b06d921edfaefe17c03bb673dc
Reviewed-on: https://review.openocd.org/c/openocd/+/6616
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since we can detect the type of target as well, make the attach
function name generic for the follow on cleanup patch on armv8 to use
as well.
Lets introduce gdb-attach event in a much cleaner fashion. We can
introduce a simpler r5_up function since we now have more descriptive
core names making the individual descriptive procs redundant.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I31506bb2b86e63638082640eb72aa7c4c9575e93
Reviewed-on: https://review.openocd.org/c/openocd/+/6617
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
R5 targets are currently named r5.0..n and the only way for user to
determine the actual type is external documentation. Lets just rename
the target names to make them descriptive to not require external
documentation for finding which R5 to connect to.
NOTE: we leave the _mcu_r5_cores _main0_r5_cores _main1_r5_cores alone
for now to allow existing startup proc functions to work, but we will
drop it in the follow on patch.
Previously:
Info : starting gdb server for j721e.cpu.r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.r5.2 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.r5.3 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.r5.4 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.r5.5 on 3341
Info : Listening on port 3341 for gdb connections
With this patch:
Info : starting gdb server for j721e.cpu.mcu_r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.mcu_r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.0 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.1 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.0 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.1 on 3341
Info : Listening on port 3341 for gdb connections
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2989efe3ae3e16754f98fa1dc9363ec4c898f7c3
Reviewed-on: https://review.openocd.org/c/openocd/+/6627
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The MCU is present on few of the SoCs and is meant as General Purpose
(GP) MCU of the system. Lets rename it to make clear what we are
debugging - esp when multiple MCUs are present in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I16132d321daf6e9b1d893fe6f92026d5aa9eb152
Reviewed-on: https://review.openocd.org/c/openocd/+/6619
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The M3 is the system controller of the system. Lets rename it to make
clear what we are debugging - esp when multiple MCUs are present in the
system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I4cd03b6068b8ce140fd254f9dd88151c4c7006d7
Reviewed-on: https://review.openocd.org/c/openocd/+/6618
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add gdb-attach event to call the "up" function of m3 and m4 allowing for
more seamless integration with gdb for end users. We still retain _up
functions for non-gdb functionality.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2e51fdbd8756f156551e589c748c3a338afa655c
Reviewed-on: https://review.openocd.org/c/openocd/+/6615
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
both stm32l5x and stm32u5x configs are almost identical except
clock config.
while at there rename target procs to avoid issues with JTAG daisy
chaining.
Change-Id: Ibbb1dfeb91a7f8d5d45744cf57dca2877f60e0c5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6596
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The current implementation crashes when executing 'tpiu create'
without an object name due to an invalid memory access. Pass 'argv'
instead 'goi.argv' to fix the problem.
While at it, match the style of the error message to the style used for
other Tcl commands. Especially, make the 'name' parameter mandatory.
Change-Id: Ib2b233f8556934af61608ae93d6405585c2c40b7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6329
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
using gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0 we get:
error: ‘retval’ may be used uninitialized in this function
fixes: 13cd75b6ec (flash/nor/stm32xx: fix segfault accessing Cortex-M part number)
Change-Id: I897c40c5d2233f50a5385d251ebfa536023e5cf7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 6541233aa7 ("Combine register lists of smp targets.")
assumes that all the targets in the SMP cluster are already
examined and unconditionally call target_get_gdb_reg_list_noread()
that will in turn return error if the target is not examined yet.
Skip targets not examined yet.
Add an additional check in case the register list cannot be built,
e.g. because no target in the SMP cluster is examined. This should
never happen, but it's better to play safe.
Change-Id: I8609815c3d5144790fb05a870cb0c931540aef8a
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6853
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Commit 6541233aa7 ("Combine register lists of smp targets.")
unconditionally assigns the output pointers of the function
smp_reg_list_noread(), even if the function fails and returns
error.
This causes a double free from the caller, that has assigned NULL
to the pointers to simplify the error handling.
Use local variables in smp_reg_list_noread() and assign the output
pointers only on success.
Change-Id: Ic0fd2f26520566cf322f0190780e15637c01cfae
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6852
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some of STM32 flash drivers read Cortex-M part number from
cortex_m->core_info.
In corner cases the core_info pointer was observed uninitialised
even if target_was_examined() returned true. See also [1]
Use the new and safe helper to get Cortex-M part number.
While on it switch also target_to_cm()/target_to_armv7m() to the safe
versions. This prevents a crash when the flash bank is misconfigured
with non-Cortex-M target.
Add missing checks for target_was_examined() to flash probes.
[1] 6545: fix crash in case cortex_m->core_info is not set
https://review.openocd.org/c/openocd/+/6545
Change-Id: If2471af74ebfe22f14442f48ae109b2e1bb5fa3b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: f5898bd93f (flash/stm32fxx.c: do not read CPUID as this info is stored in cortex_m_common)
Reviewed-on: https://review.openocd.org/c/openocd/+/6752
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
target_to_armv7m() and target_to_cm() do not match the magic number
so they are not suitable for use outside of target driver code.
Add checked versions of pointer getters. Match the magic number
to ensure the returned value points to struct of the correct type.
Change-Id: If90ef7e969ef04f0f2103e0da29dcbe8e1ac1c0d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6750
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The third parameter of container_of() should point to the same member
as target->arch_info points to, struct arm.
It worked just because struct arm is the first member in
struct armv7m_common.
If you move arm member from the first place, OpenOCD fails heavily.
Change-Id: I0c0a5221490945563e17a0a34d99a603f1d6c2ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6749
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit corrects the erase function for stm32f2x when dealing with
sectors in bank 2, for STM32F42x/43x devices with 1MB flash.
On STM32F42x/43x with 1MB flash in dual bank configuration, the sector
numbering is not consecutive. The last sector in bank 1 is number 7, and
the first sector in bank 2 is number 12.
The sector indices used by openocd, however, _are_ consecutive (0 to 15
in this case). The arguments "first" and "last" to stm32x_erase() are of
this type, and so the logic surrounding sector numbers needed to be
corrected.
Since the two banks in dual bank mode have the same number of sectors, a
sector index in bank 2 is larger than or equal to half the total number
of sectors.
Change-Id: I15260f8a86d9002769a1ae1c40ebdf62142dae18
Signed-off-by: Simon Johansson <ampleyfly@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6810
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The host repo.or.cz is often offline, creating issues for cloning
and building OpenOCD from scratch.
Already 'jimtcl' developer has dropped repo.or.cz, triggering the
OpenOCD commit 861e75f54e ("jimtcl: switch to github").
Change also the link of the remaining submodules 'git2cl' and
'libjaylink' to their respective main repository.
Change-Id: Ib513237427635359ce36a480a8f2060e2fb12ba4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6834
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code") has
removed eCos code but has left some empty function that was used
during non-eCos build to replace eCos mutex.
Drop the functions and the file that contain them.
Change-Id: I31bc0237ea699c11bd70921660f960ee406ffa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6835
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Values defined in sys/stat.h are not guaranteed to match
the constants defined by the GDB remote protocol, which are defined in
https://sourceware.org/gdb/onlinedocs/gdb/Open-Flags.html#Open-Flags.
On my local system (Manjaro 21.2.1 x86_64), for example, O_TRUNC is
defined as 0x40, whereas GDB requires it to be 0x400,
causing all "w" file open modes to misbehave.
This patch has been tested with STM32F446.
Change-Id: Ifb2c740fd689e71d6f1a4bde1edaecd76fdca910
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is helpful when you want to pretend to gdb that your heterogeneous
multicore system is homogeneous, because gdb cannot handle heterogeneous
systems. This won't always works, but works fine if e.g. one of the
cores has an FPU while the other does not. (Specifically, HiFive
Unleashed has 1 core with no FPU, plus 4 cores with an FPU.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I05ff4c28646778fbc00327bc510be064bfe6c9f0
Reviewed-on: https://review.openocd.org/c/openocd/+/6362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CPU wrongly indicate the bypas bit in the codeid.
It's the case of the NanoXplore NG-ULTRA chip that export a
configurable (and potentially invalid) ID for one of
its component.
Add an option to ignore it.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Change-Id: Ic59743f23bfc4d4e23da0e8535fec8ca9e87ff1a
Reviewed-on: https://review.openocd.org/c/openocd/+/6802
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
When log to file is enabled, the file is not closed by OpenOCD at
exit. This is reported by Valgrind as a memory leak that is still
reachable, as the internal buffers of 'FILE *log_output' are freed
by the automatic fclose() at exit.
Close the log file before exit.
Change-Id: Id472c0d04462035254a9b49ecb0a4037263c6f6f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6789
Tested-by: jenkins
If the CTI is not specified OpenOCD fails target's examination
without indicating the reason.
Drop an error message about the missing CTI.
Change-Id: I344537fb21cf38785796ba938e71890e04135509
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6788
Tested-by: jenkins
With jimtcl 0.81 the syntax of the TCL command 'expr' requires the
multiple arguments to be within curly brackets.
Update the examples in the documentation to follow the new syntax.
While there, split one example to avoid it to exceed the line size
during pdf document generation.
Change-Id: I91cca419f8273415ccb0c2ce369fc6ac476e34e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6809
Tested-by: jenkins
Changed flash driver to support writing to the user data page, as well as to any portion of the lockbits page above 512 bytes (the amount used for the actual page lock words). The top part of the lockbits page is used on at least the EFR32xG1 chips for the SiLabs bootloader encryption keys.
As presented to the user, the lockbits page is the same size as the other pages, but any attempt to write to its low 512 bytes is an error. To enforce this, efr32x_write is renamed to efm32x_priv_write and a wrapper function is provided in its place. If the user erases the lockbits page, the driver rewrites the cached lock words after the erase. When the driver erases the lockbits page in order to update the lock words, it first takes a copy of anything stored in the top part of the page, and re-programs it after the erase operation.
There are now multiple instances of flash_bank for each target, and the flash_bank instances must share their cached lock words to operate as intended. Therefore, when a bank is created, the global flash bank list is used to find any other banks that share the same target. Since some banks in the global list are invalid at the time free_driver_priv is called, reference counting is used to decide when to free driver_priv.
To avoid the need to find the lockbits flash_bank from another flash_bank, efm32x_priv_write and efm32x_erase_page now take an absolute address.
There didn't seem to be any reason to prohibit unprotecting individual flash pages, so that limitation is removed from efm32x_protect().
This addresses ticket #185.
Valgrind-clean, except for 2x 4kiB not freed/still reachable blocks that were allocated by libudev.
No new Clang analyzer warnings, no new sanitizer warnings.
Signed-off-by: Doug Brunner <doug.a.brunner@gmail.com>
Change-Id: Ifb22e6149939d893f386706e99b928691ec1d41b
Reviewed-on: https://review.openocd.org/c/openocd/+/6665
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We have the macro
#define COMMAND_HANDLER(name) \
static __COMMAND_HANDLER(name)
Use it!
Change-Id: I0e5385cb54197c743348f0d2ce215c93b8e396a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6786
Tested-by: jenkins
On 2008-03-05, before git's age, commit 6d95014674 adds a
comment about unobserved ACK supposedly sent by GDB at connection.
The ACK is sent since GDB 3.95 (1999-05-04), but a bug introduced
in GDB 6.5 (2006-06-21) and fixed in GDB 7.0 (2009-10-06) makes
GDB sending the query for "supported packets" before sending the
ACK. Due to the bug, the author of the commit failed to see the
ACK.
Change-Id: I574a8013e7d159d1c71087af83b7c2ce92be86bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6769
Tested-by: jenkins
Unlike cortex_m_load_core_reg_u32() storing core register uses
the same code pattern around DHCSR read as offered by the convenience
helper cortex_m_read_dhcsr_atomic_sticky().
Use the helper.
Change-Id: Ia947204944a8b549f3c2be7fb2f717aad18970c4
SeeAlso: 65d7629183 (cortex_m: poll S_REGRDY on register r/w)
SeeAlso: 0dcf95c717 (target/cortex_m: cumulate DHCSR sticky bits)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6767
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change [1] introduced a regression that results in comparison
in arm_jtag_set_instr() to be always true if the length of the
IR register is not 8 bit. The value on the left side
of the != operator contains only tap->ir_length number of
bits while value on the right is full 8-bit instruction code.
This forces OpenOCD to update the JTAG IR register on each
transaction even if the instruction in the JTAG IR register
is correct. This causes noticeable performance degradation,
especially with slow JTAG adapters.
[1] https://review.openocd.org/c/openocd/+/6285
time ./src/openocd -s tcl/ -f interface/cmsis-dap.cfg \
-c "transport select jtag" -f target/psoc6.cfg \
-c "init; load_image data.bin 0x08000000; exit"
Without this change:
real 0m4,863s
user 0m0,074s
sys 0m0,128s
With this change:
real 0m3,083s
user 0m0,038s
sys 0m0,098s
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Change-Id: Iaded83a04ecc7e65f18256afae582267ccc1fc59
Reviewed-on: https://review.openocd.org/c/openocd/+/6762
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Allow passing optional gpiochip number before gpio number.
If no optional chip number is passed, the one from the 'gpiochip'
configuration directive is used.
Change-Id: I16933d81581d9af4d1600c5f9fdbc832ef3fda94
Signed-off-by: Laszlo Sitzer <dlsitzer@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6742
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This board is (software wise) similar to the existing SAME54 Xplained
Pro board, with just a slightly different MCU. (Hardware wise, it
features a vastly different form factor.)
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Change-Id: I5e5435d49d333fb74471994ee84de59ed983153c
Reviewed-on: https://review.openocd.org/c/openocd/+/6747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Axel W.
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- "riscv set_prefer_sba" - removed from the doc, superseded
by the latter
- "riscv set_mem_access" - new command, new entry added
into the doc
This change only addresses the documentation. The corresponding
implementation of the RISC-V commands is already merged.
Change-Id: I3c07672cde94324407cf667504dba5402f63a543
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6743
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
These commands were extended/improved in the last drop
of RISC-V target updates. Update also the documentation
to properly describe how the commands should be used now.
Change-Id: I9e2ba6adbe1a4c032b96f5f8ff2d4791fa4c2527
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6738
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Document both find and ocd_find command under Config File Guidelines
-> Interface Config Files. find command is used in the previous
section as well but the previous section is more about using OpenOCD.
The section added is "aimed at any user who needs to write a config
file".
Change-Id: I698207fe58d564c615a15b50756aa5547a5f40b7
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6737
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Document "command mode" command Server Configuration -> Configuration
Stage. The text is taken from command's help string.
In addition to the help string, this commit explain the words
mismatch, the doc uses "stage" but the command and source code uses
"mode" to describe the same thing.
Change-Id: I1d5fc8c64a3a0b07ea8430bf016bcbd54e52da1c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6736
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ARM IHI 0031A does not support SWJ-DP, so no switch between JTAG
and SWD is considered.
ARM IHI 0031B is not publicly available and it's reported as
"Confidential Beta" in the history list in following doc versions.
From ARM IHI 0031C the direct switch between JTAG and SWD is
already deprecated in favor of passing through dormant mode. With
no access to IHI 0031B we haven't info if any device strictly
requires the direct switch.
OpenOCD implements only the deprecated direct switch, so changing
it could cause regression on devices that do not implement dormant
mode.
Plus, not all the adapters support dormant mode.
Nevertheless there are already target devices that only allow
entering in SWD by passing through dormant.
Let the code try both method, alternating one tentative with the
deprecated legacy direct switch, then another tentative passing
through dormant, and repeat till timeout.
This would work on any device that don't support dormant, on new
devices that require switch through dormant and will work with
adapters that don't support dormant.
Change-Id: Ib8619635277d497872079a33fa4e38be9beb84a0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6695
Tested-by: jenkins
The function debugport_init() has never existed in OpenOCD code,
but few comments erroneously references it in place of the
existing function ahbap_debugport_init().
Commit 00dbc185ee ("arm_adi_v5: Split ahbap_debugport_init")
splits the function ahbap_debugport_init() in dap_dp_init() and
mem_ap_init(), but did not removed all the incorrect comments
about debugport_init(). Few of such comments has been removed in
later patches.
Remove the last comment that references debugport_init().
Change-Id: Ibd1f125475386e5653340fedf706903a0ee15897
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6694
Tested-by: jenkins
Added and improved several prints related to the GDB connection
and various error states that may occur in relation to this
connection.
Change-Id: I233246190b613cc925b783561cfa3aa5267360fd
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6288
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Standard C library free() allows NULL pointer as a parameter.
Change target_free_working_area() to conform this convention.
Remove NULL pointer tests before target_free_working_area() calls.
While on it add missing setting pointer to NULL after target_free_working_area().
Change-Id: I7c692ab04a9933398ba5bc614723ad0bdecb87b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6712
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Move more smarts into the target algorithm code, and rewrite that in C
so it's easier to understand/maintain.
* Support >24-bit addresses.
* Check for errors.
Change-Id: I3b1a143589fe6defafb8f95820aa682acc9646e7
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6679
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Document usage command under General Commands -> Server Commands. The
text is taken from the command's help string.
Change-Id: I957cb46cca98181c3c5e676228c5c103e47bb655
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6735
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Document add_help_text and add_usage_text under Genral Commands ->
Misc Commands. The text are taken from command's help strings.
Change-Id: I2bbbee8e5faa8d9654227c304e0528f5144275e8
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6734
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command might be a leftover from development of the driver.
There is no documentation what it does.
Change-Id: Iaa5aa1ac51638bd6acce172a5dd03846a165dc27
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6728
Tested-by: jenkins
Reviewed-by: Ivan-Artekit <ivan@artekit.eu>
Add help texts from similar driver kinetis.c
While on it fix one existing help: the flash is obviously not NAND
Change-Id: Ibd295105586b008aaabf2fb4e4a75bf551266e38
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6727
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The stm32mp13x has one core Cortex-A7.
The board Discovery Kit includes an on-board STLink-V3 with SWD
connection.
The webpage of the board is not active yet.
Change-Id: I8836b26612a160ead79766955ebefaf3d21a329c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6675
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Now that adapter serial is handled independently from the adapter
drivers, move inside jtag_libusb_open() the call to
adapter_get_required_serial(), so every adapter that uses libusb
will automagically get USB serial support.
Extend the documentation to list the adapters involved.
Change-Id: I75b3482d38f8ed3418329f3106c5e8b689fd460b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6663
Tested-by: jenkins
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
The driver jlink defines the command 'jlink serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: in former code the commands 'jlink serial' and 'jlink usb'
were mutually exclusive; running one of them would invalidate the
effect of a previous execution of the other. The new code gives
priority to 'adapter serial', even if executed before 'jlink usb'.
Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6656
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The driver xds110 defines the command 'xds110 serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: the original command 'xds110 serial' used a complex and
undocumented conversion of the serial number through multibyte
string, wide-character string and C cast. The XDS110 I can access
and the lsusb dumps available through Google don't show any
exotic USB serial that require such conversion. The original
developer doesn't remember any constraint that mandates such
conversion (see comments in https://review.openocd.org/4322/).
The conversion is removed by this patch.
Change-Id: I38909918079b2c1797ad85ebec2fea1b33743606
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6655
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver vsllink defines the command 'vsllink usb_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Iadcc018b8aa8974ccd7156915b84e58270fad29d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6654
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver presto defines the command 'presto serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I1a69acce7d4910082d2029d5941ae84f9424314c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6653
Tested-by: jenkins
The driver kitprog defines the command 'kitprog_serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I844cb815af01137392b6d12e1b5972fc77ac092d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6652
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver ftdi defines the command 'ftdi serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Ia5b1f325b9fab8f58b5ea70f8b807e50b148b939
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6651
Tested-by: jenkins
The driver ft232r defines the command 'ft232r serial_desc' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I0bd909923a668420604fed3c9f6a260716b044c7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6650
Tested-by: jenkins
The driver cmsis_dap defines the command 'cmsis_dap_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I88e2d4de360a6c6f23529bb18494962a267250df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6649
Tested-by: jenkins
The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
Several adapter define their own command to specify the USB serial
number or serial string to be used during USB search.
Define a general command 'adapter serial' to be proposed as
replacement of the driver specific ones.
No driver is changed so far to use it.
Change-Id: I7631687a4163ccc63a9bdf3ad1fcb300fc483d3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6647
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
hla_target uses the same struct cortex_m_common as the standard cortex_m
target. Unlike the cortex_m target hla missed setting of common_magic.
Set commont_magic to help pointer verification.
Add convenience tests is_cortex_m_or_hla() and
is_cortex_m_with_dap_access()
Use proper test in cortex_m_verify_pointer() - this code relied on
unset common_magic on hla target before the change.
Change-Id: I4dae79f056c3d73adf524e26aa8ef2d3a57b471e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6741
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation included it in commit 4e79b48e2c ("Add new
target type: OpenRISC"), but the command was never added.
Remove it!
Change-Id: Ice5fa1ee4086b5f5ceb942c3ce68bc9bbd75d19b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 4e79b48e2c ("Add new target type: OpenRISC")
Reviewed-on: https://review.openocd.org/c/openocd/+/6723
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commands has been dropped in commit 150b7d26f2 ("arm_adi_v5:
Update DP (Debug Port) registers defined in ADIv5.2.") but the
documentation still keeps it.
Remove it!
Change-Id: I4e88f481d943f064d919f8065562052244122bf0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 150b7d26f2 ("arm_adi_v5: Update DP (Debug Port) registers defined in ADIv5.2.")
Reviewed-on: https://review.openocd.org/c/openocd/+/6722
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing initialization triggers a run-time error message:
Error: BUG: command 'psoc6 reset_halt' does not have the '.usage'
field filled out
Change-Id: I975e4ba99bd939aa924a9d62b1ab76b2ab5bf193
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6720
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When a struct is initialized, missing fields are already filled
with zero or NULL.
This change simplifies scripts to compare documentation and
registered commands.
Change-Id: I96fbdfa98bbb1f2b5e2a9532faf5a15cb5bc28dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6719
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Just to avoid name clash when comparing documentation with
registered commands through scripts.
Change-Id: I8832545d8d9236ea5dabe6e73732f51e5246caff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6717
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Do not split in multiple lines the calls to register_commands*().
No change in code behaviour, just make it easy to grep in the code
and identify the commands that can be registered.
This would help detecting undocumented commands.
Change-Id: Id654e107cdabf7ee31fc3d227c1d2a59acc5669e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6716
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Based on Graham Sanderson's http://review.openocd.org/4935
Unlike Graham Sanderson's version this patch does not add
any multidrop specific queuing.
Multidrop SWD is handled mostly by the same code as single SWD,
just a selection sequence is prepended to a SWD operation
as needed.
This is a minimal working implementation without checking for
configuration errors (mixing multidrop and non multidrop DPs,
multiple use of the same selection id etc...).
Multidrop switching likely demands changes in the adapter code.
Change-Id: I99a5742c209b49c0483e800f6105cb5e59a897d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6141
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
dap_configure() contained first time init related tasks, as the call to
dap_init_instance() and the check for configured tap.
Move all first time init related stuff to dap_create() to make dap_configure()
usable in eventual stand-alone 'dap configure' command.
Change-Id: Ia86eadb4e960ce54e8581630d01af75720d2318d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6702
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is a preparatory change for swd multidrop, mostly refactoring.
Split swd_queue_dp_read/write() to inner and outer parts.
Use the inner parts in swd_queue_dp_bankselect(), swd_connect()
they do not need to check reconnect.
Use the outer parts exclusively in swd_dap_ops.
Rearrange the code to reduce forward declarations.
Change-Id: I47b7f0cb037e0032a267463f06ba02123ba96fe7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6139
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Ignore ack received after DP_TARGETSEL write to prevent false error.
This change also fixes a bug:
Received ACK FAULT or JUNK value were incorrectly stored to queued_retval
and later used as bitbang_swd_run_queue() error return.
Use LOG_ERROR for parity mismatch.
Change-Id: I5ff1f658f221af78d8bbec8416a7a0fc64ba2550
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6700
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to ARM IHI0031C+ chapter 2.3.11 "TARGETSEL, Target Selection register"
multidrop capable DPv2 must not drive SWDIO line during the response phase
of a write to TARGETSEL register.
Introduce helper functions swd_cmd_returns_ack() and swd_ack_to_error_code()
to centralize these tests from all drivers to one place.
Introduce distinct error codes for SWD protocol.
Partly inspired by Graham Sanderson's http://review.openocd.org/4935
Change-Id: Ie5f9edb22e066a933a534bf2b29e7e1d3087dad1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6699
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
hla_layout.h uses explicitly tpiu_pin_protocol enum defined in
arm_tpiu_swo.h.
To make this header file consistent, add the missing include.
Change-Id: Ibecc279da8d6859ced2b8377e812554c747d81bb
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6687
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added "jtag_vpi:" prefixes to log messages from the jtag_vpi
driver. The intention is to make it clear what the messages
relate to. Without the prefix, many of the log messages
won't make much sense to the user.
This change does not alter any functionality, just
the printed text.
Example:
Before:
Error: Can't connect to 127.0.0.1 : 5555
After:
Error: jtag_vpi: Can't connect to 127.0.0.1 : 5555
Change-Id: I779c379f52722b094b200d08b25ab0f7280d2845
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6686
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Today's version of jimtcl includes a fix for autoconf >= 2.70 and
a minor fix for warnings with GCC 11.
To prepare for next jimtcl 0.81, let's merge and test the updated
master branch.
Change-Id: I455cc708f7d4786461978e38b6ac71816e2c9825
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6674
Tested-by: jenkins
Add the value DORMANT_TO_JTAG in the enum listing the SWJ-DP
switching sequences.
The corresponding bit-sequence is already available.
Change-Id: I6f1ffd29a8f5729ec70ce0303248bc251409d37d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6689
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
If the target is in a state where S_REGRDY polling is necessary (slow
clock, low power state...?), OpenOCD will continue to use the slow
path even if the condition is temporary and the target at a later
point would be capable of fast reads again.
Revert to fast reads if a full register dump can be made without need
for polling any of the registers; presumably it will succeed the next
time too.
Change-Id: I557f0d90b7ce6f9d81aa409b6400fc9c83d16008
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6678
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the change cortex_m_debug_entry() reads all registers
calling cortex_m_load_core_reg_u32() for each register with
a poor usage of JTAG/SWD queue.
It is time consuming, especially on an USB FS based adapter.
Moreover if target_request debugmsgs are enabled, DCB_DCRDR
is saved and restored on each register read.
This change introduces cortex_m_fast_read_all_regs()
which queues all register reads and a single dap_run() transaction
does all work.
cortex_m_fast_read_all_regs() reads all registers unconditionally
regardless register cache is valid or not. This is a difference
from the original cortex_m_debug_entry() code.
cortex_m_debug_entry times from -d3 log, Cortex-M4F and CMSIS-DAP
(Kinetis K28F-FRDM kit)
target_request | time [ms]
debugmsgs | without the change | with the change
---------------+--------------------+-----------------
disable | 186 | 27
enable | 232 | 29
Added checking of DHCSR.S_REGRDY flag. If "not ready" is seen,
cortex_m->slow_register_read is set and fallback to the old
register read method cortex_m_slow_read_all_regs() is used
instead of cortex_m_fast_read_all_regs().
Change-Id: I0665d94b97ede217394640871dc451ec93410254
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5321
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Accordingly to arm documentation [1], chapter C1.6.4, the
operation to read/write from/to core registers can require time,
and the specific flag DHCSR.S_REGRDY has to be polled to verify
that the operation has been completed.
The lack of check on S_REGRDY causes OpenOCD to fail handling
correctly the core registers on a Cortex-M4 emulated in a slow
FPGA, and it could also fail on devices clocked at very low speed
while using a fast adapter.
Poll S_REGRDY as specified in [1] while either reading or writing
the core registers.
A timeout of 0.5s is added. This could still be too small in some
extremely slow cases, but at least now we log the timeout event,
which can help tracking down such odd issue.
During register read include in the polling loop the read of DCRSR
and to flush the JTAG queue only once.
During register write, relax the write in DCRSR by removing the
atomicity that is now useless since followed by the atomic read to
S_REGRDY.
During register read include the read of DCRSR inside the polling
loop to relax the read of S_REGRDY since followed by the atomic
read to DCRSR.
This change has the drawback of adding other transfers to the
adapter while reading/writing the registers, so it is expected to
introduce some speed degradation during step-by-step.
[1] DDI0403E - "ARMv7-M Architecture Reference Manual"
Change-Id: I61f454248f11a3bec6dcf4c58a50c5c996d7ef81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5319
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
DCB DHCSR register contains S_RETIRE_ST and S_RESET_ST bits cleared
on a read.
The change introduces a helper function cortex_m_cumulate_dhcsr_sticky().
Call this function each time DHCSR is read to preserve S_RESET_ST state
in the case of a reset event was detected.
Introduce cortex_m_read_dhcsr_atomic_sticky() convenience helper to
read DHCSR, store it to cortex_m->dcb_dhcsr and cumulate sticky bits.
The cumulated state of S_RESET_ST is read and cleared in cortex_m_poll()
Change-Id: Ib679599f850fd219fb9418c6ff32eed7cf5740da
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6180
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m_single_step_core() used mem_ap_write_atomic_u32() to manipulate
dhcsr bits unlike the rest of code, where a specialized function
cortex_m_write_debug_halt_mask() takes place.
Unify setting of dhcsr bits and use cortex_m_write_debug_halt_mask() here as well.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9ef05ce88a9dce42e1d3d5404a4fe87ec86b5fe8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6676
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
GD32E23x from GigaDevice is cortex-M23 microcontroller and it can work with the stm32f1x driver.
Modifications are similar to this done for GD32F1x0 in #6164 (https://review.openocd.org/c/openocd/+/6164).
Configuration file is added because its cortex-M23 CPU ID is different.
I think that GigaDevice microcontrollers should be handled in an independent unit to separate them from STM32,
but nowadays quick solution is welcome.
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I91f31f5f66808bc50a8f607ac2c107e6b7c5e2b8
Reviewed-on: https://review.openocd.org/c/openocd/+/6527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit be57b0ab84 ("Update jtagspi driver for 1-, 2- and 4-byte
addresses") introduces two incorrect format string for uint32_t
data types.
This cause build failure on MacOS:
src/flash/nor/jtagspi.c:474:35: error: format specifies type 'unsigned char'
but the argument has type 'uint32_t' (aka 'unsigned int') [-Werror,-Wformat]
LOG_DEBUG("status=0x%02" PRIx8, *status);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
src/flash/nor/jtagspi.c:513:65: error: format specifies type 'unsigned char'
but the argument has type 'uint32_t' (aka 'unsigned int') [-Werror,-Wformat]
LOG_ERROR("Cannot enable write to flash. Status=0x%02" PRIx8, status);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
Fix the format string.
Change-Id: I209053317c8b26c35c6f11be0553ccccc698c551
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: be57b0ab84 ("Update jtagspi driver for 1-, 2- and 4-byte addresses")
Reviewed-on: https://review.openocd.org/c/openocd/+/6701
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
detected in ubuntu 20.04
sometimes, the stlink-server response could be segmented on multiple
packets.
this causes stlink_tcp_send_cmd to fail with the following msg:
Error: failed to receive USB CMD response
because the received_size < expected size
to fix the issue, do recv in a loop till all data is received
or timeout is reached.
Change-Id: I46cc60c231b4cc52f150ead268f843bc60c41149
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6671
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This commit introduces macros for target related log entries
(error, warning, ...) which is a very common operation in OpenOCD:
* LOG_TARGET_ERROR
* LOG_TARGET_WARNING
* LOG_TARGET_INFO
* LOG_TARGET_DEBUG
* LOG_TARGET_DEBUG_IO
The goal is to have one macro for this common operation and to
make such log entries look the same way - to make it more readable
for humans as well easier for parsing via scripts.
Change-Id: I6166565fc9040b03d3fca5c3aa44a1ccbcf96ad2
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6667
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The only purpose of include file driver.h was to expose the API
to register the adapter's commands.
Move the prototype in adapter.h, already used by openocd.c.
Change-Id: Ie1090c60ef9e5bac5ea187c87bed6e7b08d9671c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6645
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The configuration code for adapter parameters is spread around.
Move in adapter.c the code that handles the configuration of
adapter speed.
For convenience, move also the functions adapter_init() and
adapter_quit(), that anyway have no reason to be in file core.c
To simplify the review, the code moved is not modified. It will be
cleaned and adapted in the following changes.
Change-Id: I2b38975a0cd2e74d3d2de6c56ea17818ff225fd8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6641
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The configuration code for adapter parameters is spread around.
Add a struct in adapter.c aimed at containing all the adapter's
configuration data.
Move in adapter.c the code related to configuring 'usb location'
and the copyright tag.
Add adapter.h to export the functions.
While there:
- rework the copyright and the SPDX tag;
- rename the 'usb location' functions;
- remove the JTAG_SRC variable in Makefile.am.
Change-Id: I4fe0d32991a8a30e315807180688035ae9ee01ce
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6640
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The variable 'jtag' is set to 'adapter_driver' during adapter
initialization and is used:
- to check if adapter has been initialized;
- as local copy of adapter_driver.
Introduce a static flag to check if the adapter has been already
initialized and a convenience test function.
Use the test function and the original value of adapter_driver in
the code and drop the variable 'jtag'.
Change-Id: I1b1c54d3b36d7b60390985d787c8449432788141
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6639
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
jtagspi driver always used 3-byte addresses regardless of actual
device capcity. Now select 1- to 4-byte addresses depending on
device capacity.
Some devices need a special command to activate the 4-byte address
mode, a special command to accomplish this, and a further command
for setting device properties are added.
Additionally, restriction (start of range had to be page aligned)
removed.
Tested with XCS6SLX16 board and W25Q256FV in 3- and 4-byte address
modes.
Change-Id: I88b2877517a18dac460253ae6d97f3dded054e6c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/4876
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
By using jimtcl from latest master branch, the workaround added in
commit 36ae487ed0 ("jimtcl: add temporary workaround for memory
leak in jimtcl 0.80") is not needed anymore.
Revert the workaround.
Change-Id: Ia1b5804be15362d0400740c375455ee19ac09f04
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6228
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit 266a945ad3 ("jimtcl: update to version 0.80 (2020-10-29)")
adds a workaround to permit 'make distcheck' with jimtcl 0.80.
This has been fixed in jimtcl with commit d224c9a2b7b2 ("Makefile:
remove examples.api/Makefile while 'distclean'").
By using jimtcl from latest master branch, the workaround is not
required anymore.
Remove the workaround.
Change-Id: I10d91371b5a89d2a3c8599bce766f97eac44f0d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6227
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Current code assumes all the GPIO signals are manipulated via a single
32-bit register so using higher GPIOs silently fails.
Fix the check instead of trying to handle additional GPIOs (available on
Raspberry Pi Compute Modules) as that would slow the driver down.
Change-Id: Ib3b5864afb3b972d952f9b74665201cd93924959
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6658
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The main purpose of TCP server is to allow multiple clients to
connect and share the same physical stlink.
The commands RW MISC don't lock the communication between command
and answer, thus cannot prevent another client to break this
sequence. The commands are not supposed to be used in shared mode.
Prevent the use of RW MISC commands on a (possibly) shared TCP
backend.
This degrades the overall performance, but the shared mode already
adds its own overhead, so this is not really an issue.
Change-Id: I713d912a269664859c8142932a9905d24b6d3caa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6608
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Firmware versions V2J32 and V3J2 introduce the commands RW-MISC
to put in a single USB packet a sequence of mem_ap read/write.
These commands provide a significant speed improvement while
accessing the debug unit at scattered addresses.
Add the low level commands and extend high level implementation.
Skip for the moment the command to read the max number of items
allowed by the firmware and use some hardcoded values.
Change-Id: I8adc630cc0de733511e9d94533cbfe9f3b301a83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6607
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The stlink commands for buffer read/write carry the associated CSW
value that has to be used. We can dequeue any CSW write request
and add the CSW in the following buffer read/write.
In preparation to next patch that uses stlink commands misc-rw
(commands that don't handle CSW value), let's dequeue only those
CSW write that don't change csw_default.
Keep a local cache of last csw_default.
Tag the queued CSW writes that change csw_default.
Dequeue only the un-tagged CSW writes.
On buffer read/write commands, limiting the dequeued CSW write
surely adds a performance penalty. But csw_default is not changed
often so the penalty is not significant.
Change-Id: I538d257fe3c434fc97587846d759951384327f02
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6606
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Firmware versions V2J26 and V3J1 introduce the command
STLINK_DEBUG_WRITEMEM_32BIT_NO_ADDR_INC
Firmware versions V2J32 and V3J2 introduce the command
STLINK_DEBUG_READMEM_32BIT_NO_ADDR_INC
These new commands can provide speed improvement to Cortex-A
memory download (its debug port use a FIFO for data transfer).
Add the low level commands and extend high level implementation.
Change-Id: I3b65acbeaec3bd305f5568b9ee4bc9495b113448
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6605
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Detect a sequence of memory AP operations that can be issued as a
single stlink command.
This improves the data throughput during memory transfer.
Change-Id: Ifa4488513346fc7cd0c9317b7d24ef510ccfd959
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6604
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
By using the stlink commands for memory read write we can gain
some performance, but only when TAR and/or CSW are changed.
During long transfers with constant CSW and TAR auto-incremented
there is no gain, since the same amount of USB/TCP packet is used.
Plus, by dropping ADIv5 packed transfers the performance is lower
on 8 and 16 bits transfers.
This changes opens the opportunity for collapsing memory burst
accesses in a single stlink USB/TCP packet.
Initialize the values of enum queue_cmd to easily extract the word
size through a macro, even if this is not used here.
Change-Id: I6661a00d468a1591a253cba9feb3bdb3f7474f5a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6603
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Recent versions of stlink firmware allow accessing access port
other than zero and setting the CSW.
Modify the internal API to provide ap_num and csw.
There is no interest to modify HLA to use ap_num and csw, so set
and use some backward compatible defaults.
Change-Id: I3f6dfc6c670d19467d9f5e717c6c956db6faf7f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6602
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Implement a minimalist queue for DP/AP commands and reorganize the
code to use it.
There is no performance improvement; the queue elements are still
sent one-by-one on USB or on TCP during dap_run().
Change-Id: I8353563e59f883624bcc0fbe8b54955e4f27ccfa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6601
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Both HLA and ADIv5 layers limit the memory transfer within blocks
whose boundaries are aligned at 1024 or 4096 bytes.
New stlink firmware handle the ADIv5 TAR autoincrement, making
possible to send memory transfers across the boundary of 1024 or
4096 byte. OpenOCD doesn't use this feature yet.
Use the correct buffer size in the code, even if it is not used.
While there, split SWIM buffer size from JTAG/SWD case; stlink has
a dedicated command to retrieve SWIM buffer size, but currently
not implemented in OpenOCD.
Change-Id: Id46c0356ef21cead08726c044a1cd9725fd4f923
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6600
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The busy flag must be polled after each half-page write.
At low clock speeds, no issue is observed when the poll
is omitted, because the writes complete before the next
write begins. But at high clock speeds the subsequent
writes would overlap and cause the operation to fail.
The status polls are done on the target for efficiency,
since the half-pages are very small.
Change-Id: Ia1e9b4a6a71930549b3d84a902744ce6e596301b
Signed-off-by: Jimmy <nhminus@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5598
Tested-by: jenkins
Reviewed-by: Jelle De Vleeschouwer
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
Commit e3f3f60a02 ("adapter speed: require init script setting
and centralize activation from drivers to core.c") has already
dropped the only use of variable 'jtag_speed'.
Remove the variable.
Change-Id: Iff096df0022982cf90795aa62d6b3406203f7b14
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6638
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The initialization is barely readable, while actually only few
fields are set with value nor zero nor NULL.
Rewrite the initialization using C99 struct designations.
Change-Id: I4d288e6536ebe7110a184db6540223fc67361ec3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6636
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Doxygen cannot resolve the path of the files in folder contrib.
Use a path relative to current folder, as done in other files.
Change-Id: If39b416ed422b4854dd108777fa32dd4c809450a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6635
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Made no attempt to separate this out into reviewable chunks, since this
is all RISC-V-specific code developed at
https://github.com/riscv/riscv-openocd
Memory sample and repeat read functionality was left out of this change
since it requires some target-independent changes that I'll upstream
some other time.
Change-Id: I92917c86d549c232cbf36ffbfefc93331c05accd
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6529
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Freeze the IWDG watchdog when cores are halted to prevent a reset
while debugging.
The PMIC present on some board senses the nsrst and forces a power
cycle to the target. The power cycle causes the SWJ-DP to restart
in JTAG mode. If the debugger is using SWD, the mismatch triggers
an error after the reset command.
Ignore the error detected by 'dap init' and proceed executing the
handler. The error in 'dap init' will force a reconnect during the
following 'dap apid', restoring the SWD functionality.
Change-Id: I04fcda6a5b8a1b080ab4e8890ecd0754d5ed12d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6599
Tested-by: jenkins
Commit 64c2e03b23 ("flash/nor: improved API of flash_driver.info
& fixed buffer overruns") changes the prototype of the function
psoc6_get_info() but didn't update the list of parameters in the
doxygen comment.
Fix the doxygen comment.
Change-Id: I1dce018b60d080973c5e351490d4d7baba422d74
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Reviewed-on: https://review.openocd.org/c/openocd/+/6620
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Clang scan-build complains for three dead assignments:
Although the value stored to 'data' is used in the
enclosing expression, the value is never actually read
from 'data'
Value stored to 'address' is never read
Remove the useless assignment and the variable 'data'.
Change-Id: Ie8dcb74b1c1aa5eea1acd06b3c45c5b44954c9e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6592
Tested-by: jenkins
Clang scan-build complains for a dead assignment:
Value stored to 'tapstatus' is never read
Remove the assignment and add a comment to point for a potential
removal of the line.
Change-Id: Iad2fdc7e6faf650e24cc086ee74c745acb0d1c73
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6591
Tested-by: jenkins
Clang scan-build complains for five dead assignments:
Value stored to 'retval' is never read
Check the returned value and propagate the error.
Change-Id: I01172887a056d6f39ddcf2807848423970db1e89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6590
Tested-by: jenkins
Clang scan-build complains for two dead assignments:
Value stored to 'r' is never read
Use the variable in the following line, instead of re-computing
the pointer.
Change-Id: I5d4069872be9da85fb28bbe0a82020b90f1efe46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6589
Tested-by: jenkins
Clang scan-build complains for two dead assignments:
Value stored to 'retval' is never read
Since the timer callback should not return error, print an error
message if the data cannot be send out. Add a FIXME comment
because in current code there is no string/name to report which
connection has failed.
In command tpiu enable check the returned value and propagate the
error.
Change-Id: I9a89e4c4f7b677e8222b2df09a31b2478ac9ca4f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6588
Tested-by: jenkins
Clang scan-build complains about a variable assigned but never
used.
Although the value stored to 'val' is used in the
enclosing expression, the value is never actually read
from 'val'
Remove the dead assignment. While there, reduce the scope of the
variable by declaring the variable at the point of first use.
Change-Id: Ibe2b55a7d70597833cfa7f3d843e7c3d2407f2df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6587
Tested-by: jenkins
The header files under src/helper/ can currently be included with
either
#include <bits.h>
or
#include <helper/bits.h>
This is because we specify both "src/" and "src/helper/" directories
as include directories. Some files name under "src/helper/", such as
types.h, log.h, and util.h are too generic and could be ambiguous
depending on the search path.
This commit remove "src/helper/" from our include dir and make C files
include explicitly.
Change-Id: I38fc9b96ba01a513d4a72757d40007e21b502f25
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6507
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This might be incomplete. It's just a quick attempt to reduce some of
the difference between riscv-openocd and mainline. Other stack pointers
can be updated as I come across them.
Change-Id: Id3311b8a1bb0667f309a26d36b67093bfeb8380a
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6586
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Either for testing new commands and to retrieve information that
don't fit in any specific place of OpenOCD, for example monitoring
the target's VDD power supply from a TCL script.
Change-Id: Id43ced92c799b115bb1da1c236090b0752329051
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6564
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The driver is in OpenOCD since 2007, but the USB VID/PID have
never been listed in udev rules.
Change-Id: I77df469929dd7f6b6483678c0e76f22c30a7614c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6563
Tested-by: jenkins
For example: before this change in cortex_m_examine, if we fail reading CPUID
we return a failure code but target was set to examined which is not consistent.
Change-Id: I9f0ebe8f811849e54d1b350b0db506cb3fdd58f4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Giving the example of STM32WL55x the examine log is the following:
Info : stm32wlx.cpu0: hardware has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: hardware has 4 breakpoints, 2 watchpoints
After this change the examine log becomes:
Info : stm32wlx.cpu0: Cortex-M4 r0p1 processor detected
Info : stm32wlx.cpu0: target has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: Cortex-M0+ r0p1 processor detected
Info : stm32wlx.cpu1: target has 4 breakpoints, 2 watchpoints
Change-Id: I1873a75eb76f0819342c441129427b38e984f0df
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6553
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some MCUs (e.g. the STM32F3) directly expose the internal reset line to
an external pin. When this signal is driven by a push/pull line, it can
actually be inhibited by the external driver. This results in a setup
where the MCU cannot reset itself, for example, by a watchdog timeout or
a sysreset request. To fix this condition, support for open drain output
on the SRST line is required.
Note that because `reset_config srst_open_drain` is the default, all
users of this adapter will switch over to an open drain output unless
explicitly configured otherwise.
Signed-off-by: Alex Crawford <openocd@code.acrawford.com>
Change-Id: I89b39b03aa03f826ed3c45793412780448940bcc
Reviewed-on: https://review.openocd.org/c/openocd/+/6559
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1. Use TCP_NODELAY, which makes things twice as fast.
2. Get rid of a bunch of unnecessary socket block/non-block calls, which
improves speed another 10% or so.
Change-Id: I415db5746d55374a14564b1973b81e3517f5cb67
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6534
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The jimtcl API Jim_GetCommand() sets an error message when the
command is not found and flag JIM_ERRMSG is set.
OpenOCD is checking if the command has already been registered,
thus 'command not found' is the desired case.
Pass flag JIM_NONE to prevent jimtcl from setting the error
message.
Change-Id: I3329c2f8722eda0cc9a5f9cbd888a37915b46107
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6562
Tested-by: jenkins
Commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
is not handling correctly the old 'tpiu' command if it is run
during the config phase (before command 'init').
Move the call to the old event handler 'trace-config' in function
jim_arm_tpiu_swo_enable(), so it is correctly executed after
'init'.
Add the call to the old event handler 'trace-config' also during
jim_arm_tpiu_swo_disable(), to match the old behaviour.
Add more information while alerting that the event 'trace-config'
is deprecated.
Change-Id: If831d9159b4634c74e19c04099d041a6e2be3f2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
Reviewed-on: https://review.openocd.org/c/openocd/+/6561
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
The initial version of the table dap_part_nums contains only the
part number of the device and not the manufacturer ID.
This causes collisions between devices with same part number but
from different manufacturer.
The table has been extended to include the manufacturer JEDEC code
in commit 2f131d3c30 ("ARM ADIv5: CoreSight ROM decode part
number and designer id").
For two old/legacy table's entries reported without manufacturer
code it was defined a special ANY_ID manufacturer, meaning skip
the check for manufacturer!
The two legacy entries report the comment "from OMAP3 memmap", and
thanks to the associated string has been possible through Google
to identify a Master Report [1] about using OpenOCD with the OMAP3
in a BeagleBoard. The ROM table is printed with OpenOCD command
"dap info 1" at page 8 and reports the Peripheral ID required to
extract the manufacturer ID that, out of any surprise, belong to
Texas Instruments.
Set the two missing manufacturer ID to Texas Instruments JEDEC
code.
Remove the now redundant definition and use of ANY_ID.
While revisiting this old code, remove also the useless comment
"0x113: what?". It was introduced in commit ddade10d4a ("ARM
ADIv5: "dap info" gets more readable") and from the same dump in
[1] it's clearly another element in OMAP3. It is listed as entry
0x8 in the ROM table and there is no further info available.
OpenOCD will anyway list it as:
Designer is 0x017, Texas Instruments
Part is 0x113, Unrecognized
Another link https://elinux.org/BeagleBoardOpenOCD reports the
text "Part number 0x113: This is ????", which sounds familiar!
No public document from Texas Instruments reports what is this
device at address 0x54012000.
[1] Warren Clay Grant - University of Texas at Austin
"Implementation of an Open Source JTAG Debugging Development
Chain for the BeagleBoard ARM® Cortex A-8" - May 2012
Link: https://repositories.lib.utexas.edu/bitstream/handle/2152/ETD-UT-2012-05-5478/GRANT-MASTERS-REPORT.pdf
Change-Id: I7e007addbb5c6e90303e4e8c110c7d27810fbe9c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6454
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
The complete AP type should include 'class' and 'manufacturer'.
Cleanup the definition of AP type from AP_REG_IDR register.
Include the check of 'class', together with manufacturer and type.
Add the new MEM-AP from ARM IHI0074C.
Change-Id: Ic8db7c040108ba237b54f73b1abe24b8b853699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6447
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Several magic numbers related to ARM CoreSight specification
IHI0029E are spread around OpenOCD code.
Define through macros the ARM CoreSight magic numbers and collect
them in a single include file.
Use the new macros wherever possible.
Change-Id: I9b0c1c651ce4ffbaf08d31791ef16e95983ee4cb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6446
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This partially reverts commit 1247eee4e6.
There is no reasonable use cases where work-area should be enabled
and working, and it can't be used for the flash loader.
Instead of introducing driver specific property, users can disable
flash load by disabling work-area, for example by setting it to 0.
But still we keep the function stm32l4_write_block_without_loader
to be used when workarea is not available (no sufficient size or zero)
Change-Id: Ibb046c74df354c6067bac978e8ef7efb47d9fd2b
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6569
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
the echo command is managed through command handler and not jim_handler
to be consistent rename the handler from jim_echo to handle_echo
and update the return values
Fixes: 4747af362d (JIM: document "echo" command)
Change-Id: I5ae87ea802d8430b573fb83daa6b35490b5d5775
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6549
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We are already at the limit for the number of VID/PID pairs declared
in stlink.cfg and stlink-dap.cfg. Increase the maximum number of pairs
from 8 to 16 to make room for a few more devices.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Ifad8e7ef67b930edbb5421730f00eb3390812f06
Reviewed-on: https://review.openocd.org/c/openocd/+/6554
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The NULL pointers preceded by cast where not detected by the
scripting tools looking for NULL pointer comparison.
Remove them and, while there, further simplify the code and apply
the other coding style rules.
Change-Id: Ia7406122e07ef56ef311579ab0ee7ddb22c8e4b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6539
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
stm32l4_work_area struct is shared between the loader and stm32l4x flash driver
'*wp' and '*rp' pointers' size is 4 bytes each since stm32l4x devices have
32-bit processors.
however when used in openocd code, their size depends on the host
if the host is 32-bit, then the size is 4 bytes each.
if the host is 64-bit, then the size is 8 bytes each.
to avoid this size difference, change their types depending on the
usage (pointers for the loader, and 32-bit integers in openocd code).
Change-Id: I0a3df4bb4bf872b01cdb9357eb28307868d7d469
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6556
Tested-by: jenkins
Reviewed-by: Yestin Sun <sunyi0804@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This works well with gdb on RISC-V, since hardware breakpoints are
per-core and gdb thinks that targets are really processes on a machine.
Are there targets where this is a bad idea? Should the target definition
specify whether this behavior is desired or not?
Change-Id: Ia32be2707b04347fd8bf2ca6fbb2b0ceaad3704a
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6528
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The 'flash list' command returns the driver name as flash name which seems
to be incorrect, the proposal is:
- to fix this by returning the flash name
- and add a new item 'driver' in the returned list
example:
before the change
> flash list
{name stm32l4x base 134217728 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 201326592 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 200933376 size 0 bus_width 0 chip_width 0}
after the change
> flash list
{name stm32l5x.flash_ns driver stm32l4x ...}
{name stm32l5x.flash_alias_s driver stm32l4x ...}
{name stm32l5x.otp driver stm32l4x ...}
Change-Id: I6d307b73c457549981a93c260be344378719af82
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6425
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This version of jimtcl:
- fixes memory leak in API Jim_CreateCommand();
- fixes 'make distcheck';
- uses single-argument syntax for 'expr'.
With the 'expr' syntax already fixed in all the tcl scripts in
OpenOCD, let's use the latest jimtcl to check it and anticipate
any further issues.
By using this version, the workaround for the memory leak and for
distcheck can be reverted.
Change-Id: I58e1bdc752a728f1b479de1c55067b698e817ef5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6226
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
All the scripts distributed with OpenOCD are already compliant
with the new syntax.
To avoid breaking user script, introduce a replacement for 'expr'
command that handles the old syntax while issuing a deprecated
warning.
This change should be part of OpenOCD v0.12.0, then reverted.
Change-Id: Ib08aa8ebcb634c81a3ce9d24fb4938b0418c947c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6510
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
STM32WB1x devices has a single flash bank up to 320 KB (page 2KB)
note: STM32WB5x/WB3x are single banks as well but do have 4KB as page size.
note: remove the assert that checks if max_mages is power of two, because
STM32WB1x flash size is not a power of 2
Change-Id: Ib514cf989ecb819d25d1c4a65d641d0a1a3d9f18
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6129
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
switching to C loader instead of the assembly version will enhance readability
will reduce the maintenance effort.
besides the switch to C loader, we added a new parameters to the loader
like flash_word_size and flash_sr_bsy_mask in order to support properly
STM32U5x and STM32G0Bx/G0Cx in dual-bank mode.
Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6109
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
instrument the telnet_move_cursor to detect when there is no change
of cursor position and if the requested new position is out of bounds.
Change-Id: I24da877e538a458da6d2f8ddc2a681eee404d2cb
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6441
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
like in terminal 'CTRL+C':
- keeps the line content so the user can refer to it (like copy/paste)
- marks the line with '^C', as hint that the command was not executed
- permit the user to write a new command
Change-Id: Ib784c827d64fdc439a35db461d8387a62d3bfbbf
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6439
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Commit dcdf71c21b ("- fix signed/unsigned build errors under
win32. Thanks Zach Welch <zw@superlucidity.net>") in 2009 prevents
gcc warnings on sign/unsigned comparisons while building for Win
on folders 'helper' and 'server'.
In 2011, commit b69119668e ("RTOS Thread awareness support wip")
uses the same method on the new folder 'rtos'.
In mean time, all the incorrect sign/unsigned comparisons has been
fixed and no warning is present with the default -Wextra flag that
implies -Wsign-compare.
The comment:
# FD_* macros are sloppy with their signs on MinGW32 platform
seems linked to some old implementation of MinGW32 include file
that doesn't apply on current versions.
Remove the obsolete hacks to suppress the warnings.
Change-Id: I76dba9e54a647d3b9fbf1b7e9ae1844e3d7adc9a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6254
Tested-by: jenkins
Reviewed-by: Xiaofan Chen <xiaofanc@gmail.com>
Libusb v1.0.9 has been released on April 2012. We can reasonably
expect that every user has already updated his system to a libusb
newer of equel to v1.0.9.
Remove the fix for older libusb.
Change-Id: I0c40e53d7af85a11b0bb265bbf8035857a2dfce1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6253
Tested-by: jenkins
Reviewed-by: Xiaofan Chen <xiaofanc@gmail.com>
If the remaining memory for the buffer is less than 256 bytes,
the memory allocated for the write algorithm in the target is not freed.
Fixes: ba131f30a0 (Flash driver for STM32G0xx and STM32G4xx)
Change-Id: Ic649f6c39799d76725b0c69ff3a009a3f510e17f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6486
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
When running OpenOCD with -fsanitize=undefined, a warning is emitted
for an bit-shifting operation whose result cannot be stored in a
signed integer.
This is because (1 << 31) overflows a signed integer, which is
undefined behavior. By making each of the bit masks act on an
unsigned number, the warning is avoided.
Whether this warning emitted by UBSan would ever manifest into a real
error is debatable, but fixing this does make UBSan happy.
Change-Id: I0455a26b234cb4f5e239a6ba90023d28380e9464
Signed-off-by: Sebastiaan de Schaetzen <sebastiaan.de.schaetzen@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6429
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this device has a dual bank flash architecture up to 512 KB (page 2KB)
reference: RM0444 Rev 5
notes:
- 128k variant is always single bank
- 256k variant flash is contiguous (no gap) in dual bank mode
- BKER is bit 13 vs bit 11 for other devices
> added cr_bker_mask in stm32l4_flash_bank struct
- BSY2 for bank 2 operations
> added sr_bsy_mask in stm32l4_flash_bank struct
> proposed optimization: always wait for (BSY1 | BSY2) with
STM32G0Bx/G0Cx devices only (for L4+ devices BSY2=PEMPTY)
TODO: update flashloader to use the proper BSY bits
temporarily don't use the loader in dual bank mode
Change-Id: I54b0c93b494e7209da818791d15edd8cd42c2732
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6036
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
This struct element is replaced by the usage of F_HAS_L5_FLASH_REGS flag:
since over this driver stm32l4_flash_regs is the default register layout,
and the only exception is STM32L5 family,
so it's simpler to manage it using a flag.
Note: the same flag will be used with STM32U5 devices, as they have
the same registers layout, which explains the move of stm32l5_s_flash_regs
before the switch(device_id) in order to not re-write this for STM32U5.
Change-Id: I3b67a6f558d9350f609a22524012b6fceb7de7c2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6435
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this capability permits to program the flash if we cannot reserve a workarea.
the introduction the command 'stm32l4x flashloader <bank_id> [enable|disable]'
helps to automatically skip using the flashloader if needed.
Change-Id: Id29213c85ee5c7c487cfee21554f5a7ea50db6c9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6273
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
auto re-probing is ensured by having optr cache set in the
last probe operation.
this will help to detect if flash options have been modified by the
running application or by the user using direct register access.
Change-Id: I05cd7ab9e83a7fc26ac6cff175b3c11b0efa2eb5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5935
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this command will help to enable/disable or display the TrustZone security,
using the TZEN option bit.
Note: This command works only with devices with TrustZone, eg. STM32L5.
Note: This command will perform an OBL_Launch after modifying the TZEN.
Change-Id: I4aef15bf57d09c1658d37858143d23b1d43de1f0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
in line 1391, get_stm32l4_bank_type_str(bank) will always output the same
value "Flash single" since the variable stm32l4_info->dual_bank_mode is false
by default, stm32l4_info->dual_bank_mode will be set correctly afterward
in the switch case at line 1467
thus the need to remove the usage of get_stm32l4_bank_type_str(bank) before
stm32l4_info->dual_bank_mode initialization.
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Change-Id: Ia8dc7e144e0ded6143682eb514c247f27859ff81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6411
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
As per Arm Debug Interface Architecture Specification (ADIv5.0 to
ADIv5.2), B3.3.1, the JTAG-DP as an IR length of 4 or 8 bits
depending on the ARM implementation. The current code
only support 4-bit and this patch extends the support to 8-bit IR.
Not tested back yet on a 4-bit target.
Change-Id: Ie4f875dc336caf014c6cfced57574b54d0970623
Signed-off-by: Antoine C. <acalando@free.fr>
Reviewed-on: https://review.openocd.org/c/openocd/+/6285
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Current implementation ignores the flag '-ap-num' provided to
command 'target create' and searches for the first AP of APB type.
If specified, use the ap number.
Change-Id: If1ac12345220d14a4a60515efe46dc2a2eac079a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6413
Tested-by: jenkins
JEP106 encodes JEDEC-assigned manufacture code as:
a) a sequence of zero or more escape codes 0x7f;
b) an odd-parity bit of the next 7 bits;
c) 7 bits.
The same code is often represented as a single value composed by
the logical OR between:
- the number of escape codes in a), shifted left by 7 positions;
- the 7 bits in c).
This is the preferred packed representation used by this change.
Currently there are only two uses of JEP106 in openocd to get the
manufacturer name:
- to decode the JTAG IDCODE of each TAP, where the JEP106 code is
already packed as in the preferred representation above in bits
IDCODE[11:1];
- to decode the ARM CoreSight PIDR register, where the JEP106 code
is split in 3 parts:
= PIDR3[3:0], corresponding to bits [10:7] of the packed code;
= PIDR2[2:0], corresponding to bits [6:4] of the packed code;
= PIDR1[7:4], corresponding to bits [3:0] of the packed code.
Wrap the existing JEP106 decode function in a simpler API using
the packed code.
Simplify the callers by skipping the bit unpacking.
Change the manufacturer code in CoreSight table dap_partnums[] to
match the packed representation, by removing the always-one bit 7
erroneously taken from PIDR bit JEDEC and included in the former
table.
Change-Id: I63eb4da9e6801fab25e330f1f6b792d2fd619493
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6418
Tested-by: jenkins
Update the list of ARM coresight classes wrt to latest ARM
documentation.
Use c99 array designator to easily track changes in future.
Add a comment for the entry "OptimoDE DESS". It was added in 2009
by David Brownell, but Google cannot find any reference other than
this line in openocd code its associated commit. It should not be
an issue keeping it as is.
Change-Id: Ia3b646131ee68ca5263095c3a0aeaf75c004b324
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6431
Tested-by: jenkins
In case of multi-word commands, the command dispatcher is nested
called at each word during command name parsing.
The improper position of the call to script_debug() causes the
command line to be logged once at each parsed word.
In the example of command "cpu arm disassemble 0" the full command
is logged three times for "cpu", "arm" and "disassemble":
Debug: 656617 61843 command.c:201 script_debug(): command - cpu arm disassemble 0
Debug: 656618 61843 command.c:201 script_debug(): command - cpu arm disassemble 0
Debug: 656619 61843 command.c:201 script_debug(): command - cpu arm disassemble 0
Call script_debug() only when the parsing is terminated and the
command handler is going to be executed.
Change-Id: Ide4cb01b3b38912e2e24b073c94a9560f92d30bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6436
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The command 'step' accepts an optional parameter 'address' to run
the step-by-step execution from an address different from current
program counter.
When OpenOCD sets the new program counter value in the register
cache, it doesn't flag it as dirty. The following call to function
armv7m_restore_context() does not propagate the new value of the
program counter to the target. This cause the target to continue
from the old program counter value, ignoring the user's request.
It is hard to notice the issue if the target is halted in an idle
loop! In fact the default mode to operate step-by-step is to set a
breakpoint to the following instruction and resume execution. In
the idle loop the CPU will pass through the breakpoint whatever
the resume address is. User will find the target halting at the
instruction following 'address' which is consistent with the
expected behaviour of command 'step address'.
To verify the issue on an STM32F4, use a dummy code in SRAM:
halt
mww 0x20000000 0xbf00bf00
mww 0x20000004 0xbf00bf00
mww 0x20000008 0xe7fcbf00
arm disassemble 0x20000000 6
0x20000000 bf00 nop
0x20000002 bf00 nop
0x20000004 bf00 nop
+--> 0x20000006 bf00 nop
| 0x20000008 bf00 nop
+-<- 0x2000000a e7fc b #0x20000006
resume 0x20000006
halt
step 0x20000000
the target doesn't halt because it is in the loop from 0x20000006
to 0x2000000a. The 'step 0x20000000' did not changed the program
counter so the temporary breakpoint at 0x20000002 is never hit.
Then:
halt
step 0x20000008
target halted ...
... pc: 0x2000000a
gives the feeling that only the instruction at 0x20000008 has been
executed, but actually the whole loop has been executed from the
place 'halt' stopped the execution till the breakpoint at the
instruction following 0x20000008.
Flag the program counter cached value as 'valid' and 'dirty' to
force armv7m_restore_context() to update the target's register.
Change-Id: I49bd8bb95b2f5429ec38ed016f2ad706618ae68a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6434
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 89f07325f2 ("stlink: Set speed before entering JTAG/SWD
mode") anticipates setting the adapter speed just before entering
in the JTAG/SWD mode. This to initiate the communication with the
speed selected by the user.
But SWIM doesn't allow setting the speed before entering in SWIM
mode. The resulting error causes OpenOCD to quit.
The problem only happens with stlink-v3, due to the different way
to set the adapter speed on different stlink versions.
Set the speed before entering in the mode only for JTAG and SWD
modes.
Change-Id: Iab42cd9d72ecfac14c7e17bae74e0dee2218b235
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 89f07325f2 ("stlink: Set speed before entering JTAG/SWD mode")
Reviewed-on: https://review.openocd.org/c/openocd/+/6443
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This protects against out-of-bounds writes when the memory
of RIOT's scheduler is corrupted.
This memory can be corrupted because of:
- Programming errors
- The scheduler not yet having been initialised
- An incorrect symbol file being used during debugging.
This error can result in OpenOCD segfaulting. Valgrind was
used to find the approximate location of the error.
Change-Id: I60e7d7c245b8c4e38f4c98cb0c0347a9b5ec3177
Signed-off-by: Sebastiaan de Schaetzen <sebastiaan.de.schaetzen@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6381
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: Ia7fe9c4017108616f21676f115f151ac62924205
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6423
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I972da1a75ba7c41c1b714c2429289c3d24594235
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6422
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: Ibfe95ce73f147f467de8de23e9573ef0179aed96
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6421
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I14061cb48da6bac13f9d2896190136f5784b8c07
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6424
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Current github build for windows is using dynamic libraries,
but libftdi is requiring libusb static libraries.
As a quick solution, just get rid of libftdi till it can be linked without
static libusb.
Change-Id: I9c7cb0b8853459ca48589674498403e255ade5cc
Reported-by: Xiaofan <xiaofanc@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6384
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Use a command group 'ft232r' with subcommands instead of individual
commands with 'ft232r_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0dbeb4716330c83f8ce89b0d054eb0286b887bdf
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6409
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'usb_blaster' with subcommands instead of individual
commands with 'usb_blaster_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2ae3d96ba864c20d7db67c74677781a62bfc4eb5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6407
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'buspirate' with subcommands instead of individual
commands with 'buspirate_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Id999d4ba276af576fb22b76052f3c0a1f3e1b876
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6404
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'sysfsgpio' with subcommands instead of individual
commands with 'sysfsgpio_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I103d8d9b0e3169a916d944a999579746f6f6a59c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6402
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'linuxgpiod' with subcommands instead of individual
commands with 'linuxgpiod_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Iad9b330363f81128ab1ec1cbc498df28ba2ca152
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6400
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'jtag_vpi' with subcommands instead of individual
commands with 'jtag_vpi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Ie1fcc2cc138796d27f1e862692bb9ef8b11bc10d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6398
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'bcm2835gpio' with subcommands instead of individual
commands with 'bcm2835gpio_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I8f7b14273b1b2813ac3c9704605d175fa2053008
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6396
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'jtag_dpi' with subcommands instead of individual
commands with 'jtag_dpi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I19271546235a3c6737f975976a0bf0a2f66cbbe7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6394
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'vsllink' with subcommands instead of individual
commands with 'vsllink_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I59273bd7cd08c9801e4a9b3de7beaa86ca854622
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6393
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'ulink' with subcommands instead of individual
commands with 'ulink_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I600d65de2bbd5fb8107445f7fe93b6b24c572e3e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6392
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'xlnx_pcie_xvc' with subcommands instead of individual
commands with 'xlnx_pcie_xvc_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0deaaa14ed14f65bf356f3c248331bfab472f08d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'presto' with subcommands instead of individual
commands with 'presto_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I883d8d87fd457d29cee8d12cd80f2e6c405e8f42
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6390
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'remote_bitbang' with subcommands instead of individual
commands with 'remote_bitbang_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2692320f19c8a357112a365db6ca7e13cd6ad411
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6389
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'openjtag' with subcommands instead of individual
commands with 'openjtag_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Ie1b1bf0b7c03e7703cfb074e554288384bf7b1b9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6387
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'parport' with subcommands instead of individual
commands with 'parport_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I4cb7096a8ba8d6cd7a6dc970862cd73c32b5c0a2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6385
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Remove useless setting of the 'is_erased' flag after a flash
modification. Also, remove code that erroneously depends on
this flag.
Keep the flag for now since it is still used by the
erase_check() functionality.
See commit 07da3b3913
Change-Id: Ia046905bc9e0cb2572145f19251c3e10c4e2d553
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6279
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By pressing CTRL-C on a running openocd with FTDI adapter, it's
possible to generate a segmentation fault that with valgrind is
dumped as a SIGABRT:
^CError: libusb_handle_events() failed with LIBUSB_ERROR_INTERRUPTED
==16594== Invalid read of size 8
==16594== at 0x48B2472: libusb_submit_transfer
==16594== by 0x48B4B0F: libusb_control_transfer
==16594== by 0x1A6B9D: mpsse_purge (mpsse.c:428)
==16594== by 0x1A7B96: mpsse_flush (mpsse.c:953)
==16594== by 0x19BA5B: ftdi_execute_queue (ftdi.c:654)
...
==16594== Address 0x6158568 is 72 bytes inside a block of size 216 free'd
==16594== at 0x484118B: free (vg_replace_malloc.c:755)
==16594== by 0x1A7B88: mpsse_flush (mpsse.c:950)
==16594== by 0x19BA5B: ftdi_execute_queue (ftdi.c:654)
...
==16594== Block was alloc'd at
==16594== at 0x48435FF: calloc (vg_replace_malloc.c:1117)
==16594== by 0x48B2259: libusb_alloc_transfer
==16594== by 0x1A7A26: mpsse_flush (mpsse.c:880)
==16594== by 0x19BA5B: ftdi_execute_queue (ftdi.c:654)
...
==16594== Process terminating with default action of signal 6 (SIGABRT):
dumping core
...
Aborted (core dumped)
The error is in mpsse_flush() that, following valgrind dump:
- allocates the buffer at line mpsse.c:880
read_transfer = libusb_alloc_transfer(0);
- frees the buffer at line mpsse.c:950
libusb_free_transfer(read_transfer);
- still pretends to use the freed buffer at line mpsse.c:953
mpsse_purge(ctx);
Move the call to mpsse_purge() right before freeing the buffer.
Change-Id: I47c71ec8c283f4b037fdd7cd72ca2e877cd3a851
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6417
Tested-by: jenkins
Commit 11019a824d ("adi_v5: enforce check on AP number value")
introduces the macro DP_APSEL_MAX and use it in place of hardcoded
magic numbers for the upper limit of AP selection value.
Fix one more place where the macro should be used.
Change-Id: I6c57f72405c69bbb40924221309d95dfeb5f7540
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 11019a824d ("adi_v5: enforce check on AP number value")
Reviewed-on: http://openocd.zylin.com/6415
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cti access is based on dap.
During cleanup, drop cti before dropping dap to guarantee that cti
can still access its dap.
Change-Id: I40c7f67d4d4a32f53802c0ce7668a5321a05893c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6414
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Commit ac22cdc573 ("target/adiv5: Large Physical Address
Extension") reads the register MEM_AP_REG_CFG and keeps it in a
new field of struct adiv5_ap. The test on LE bit (Large Extension)
is used to identify if mem_ap addresses are 32 or 64 bits.
But the register MEM_AP_REG_CFG is only read during mem_ap_init(),
that is called only when the AP is used as a target debug AP or if
a target mem_ap is attached to that AP.
The openocd commands '<dapname> baseaddr', '<dapname> info' and
'dap info' can be executed on AP that has not been associated yet
to a target, thus executed without any knowledge of MEM_AP_REG_CFG
value. The initialization to ADI_BAD_CFG causes openocd to always
use 32 bit mode on un-associated APs.
Verify if MEM_AP_REG_CFG has not been read and eventually read it.
In case of 32 bits mode AP, MEM_AP_REG_BASE64 is defined as 'RES0'
(reserved, but readable); the code can queue both the read of
MEM_AP_REG_CFG and MEM_AP_REG_BASE64, before knowing if the former
is required. This speeds-up the operation.
Rename ADI_BAD_CFG as MEM_AP_REG_CFG_INVALID.
Change-Id: If3bbd792b56a483022c37ccc2ce82b5ba5c36caa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ac22cdc573 ("target/adiv5: Large Physical Address Extension")
Reviewed-on: http://openocd.zylin.com/6412
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
In both arm ADIv5 and ADIv6 documentation, for both Class 0x1 and
Class 0x9 ROM tables, the offset field from ROM tables is supposed
to be a signed value: "Negative values of OFFSET are permitted,
using two’s complement."
The commit ac22cdc573 ("target/adiv5: Large Physical Address
Extension") extends to 64 bits the addresses while managing the ROM
tables. The offset is read as unsigned and in the former 32 bits
implementation the wrap-around was hiding the need for converting
the offset to signed. The new implementation requires the proper
cast to the offset.
On a STM32F411, without this fix the ROM table dump is incorrectly
reporting addresses out of the 32 bit bus range:
MEM-AP BASE 0xe00ff003
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00000a0411
Designer is 0x0a0, STMicroelectronics
Part is 0x411, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
ROMTABLE[0x0] = 0xfff0f003
Component base address 0x1e000e000
^^^^^^^^^^^
Cast the offset before adding it to the base address of the ROM
table.
Change-Id: I8d31fd2b3d657286cb96f8e22fb00842baa728f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ac22cdc573 ("target/adiv5: Large Physical Address Extension")
Reviewed-on: http://openocd.zylin.com/6410
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
OpenOCD has to often align values or check for alignment.
Use a dedicated set of macros instead of reinventing the wheel
each time.
Change-Id: Ia58711608aae0801deeaccb5f33148f2073b0bbd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6374
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
- Added two debug prints that allow to inspect the symbol
lookup process (carried out via the qSymbol packets).
- Added a check for an edge situation when the debugger
would send us different symbol than what we asked for
(avoids NULL dereference).
Change-Id: I84ae1b2b66473eab76a7966c678d2777b6ef48d6
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6287
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This warning about "maybe uninitialized" variable
used to pop up on certain versions of GCC.
Change-Id: I1cf43b9600885d507afc1dc042322a06751fe146
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6290
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
During the build of the OpenOCD snapshot via GitHub Actions, ensure that
the local package database is first updated, prior to installing any
packages via apt-get install. Otherwise the apt-get install could fail.
Change-Id: If3c29faeb1496d5e2be75350f6352575b1f3a42e
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6378
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Implementation for Cortex-M does works for Cortex-R too,
it allows me to fetch thread list and their backtrace on
a Cortex-R platforms.
Change-Id: I23e6eb00879587ba36e0bfb560f7002a9653d39b
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Reviewed-on: http://openocd.zylin.com/6369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The existing implementation blocks in select() for a fixed amount of
time. This change tracks when the next event (likely poll()) wants to be
run, and uses a shorter timeout in select() if necessary.
Also track all these timeouts using milliseconds as returned by
timeval_ms() instead of `struct timeval` to simplify the code.
This feature is helpful if poll() wants to do something like sample PCs
or memory values for basically the entire time that otherwise OpenOCD
would be hung in select(). See
https://github.com/riscv/riscv-openocd/pull/541 for an example of that.
The RISC-V code using this change will be upstreamed some day, too.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I67104a7cf69ed07c8399c14aa55963fc5116a67d
Reviewed-on: http://openocd.zylin.com/6363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds documentation for the bcm2835 interface configuration
parameters to the user manual. Documentation format is based on
the FTDI interface section, and was taken from the descriptions
in the driver source code.
Change-Id: I77b09b8bd44d8e8fe9cc5fb9de3c3a30550d943c
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6376
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Adds a new, optional configuration "bcm2835gpio_swdio_dir_num" to
the BCM2835 driver, to control the direction of an external buffer
driver IC in SWD mode. For example, this is needed to use a level-
shifting buffer, such as the SN74LVC2T45 used on the JTAG Hat
Change-Id: If5c146f310ecf8ceae85443b3670936467d2786d
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6371
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Commit fceb29d03f ("jtag/aice: use macros in place of const
variables") replaces some 'static const uint8_t' with macros.
This breaks the build on MacOS because the macro values are of
'int' type that doesn't match with the printf format 'PRIx8'.
error: format specifies type 'unsigned char' but the
argument has type 'int' [-Werror,-Wformat]
Replace the printf format 'PRIx8' with 'x'.
While there, remove a useless cast to uint32_t and fix the printf
format too.
Change-Id: Ib87298a61637b75a2813f209e5209d39ab2745f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fceb29d03f ("jtag/aice: use macros in place of const variables")
Reviewed-on: http://openocd.zylin.com/6380
Tested-by: jenkins
Due to Freenode takeover it's likely that most of our users are going to
seek support on Libera in the nearest future.
Change-Id: I98db95bab51f4ef2ac854bf521468d22b2794e56
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6297
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
The Broadcom Brahma-B53 CPUs contains a number of custom ROM table
entries for its PMU, Debug unit, and a couple of ROM tables.
Change-Id: I1f21f07ed296579c374f24e781325789bf4ebf51
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6368
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new checkpatch can automatically fix the code, but this
feature is still error prone and not complete.
Patch generated automatically through the new checkpatch with
flags "--types CONSTANT_COMPARISON --fix-inplace".
Some Yoda condition is detected by checkpatch but not fixed; it
will be fixed manually in a following commit.
Change-Id: Ifaaa1159e63dbd1db6aa3c017125df9874fa9703
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6355
Tested-by: jenkins
For the remaining NULL comparisons, remove then manually.
While there, make more readable a loop, by moving the assigment
out of the loop condition.
Change-Id: I44193aaa95813156a3a79c16b80e1ad333dc1eaf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6353
Tested-by: jenkins
Patch generated automatically through a modified checkpatch that
detects the patterns
if (NULL == symbol)
if (NULL != symbol)
and through flags "--types COMPARISON_TO_NULL --fix-inplace".
The unmodified checkpatch detects this pattern as Yoda condition,
but it's odd fixing it as Yoda condition and then again as NULL
comparison. This triggered the modification to the script.
Change-Id: I5fe984a85e9c4fc799f049211797aef891ebce18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6352
Tested-by: jenkins
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I7cc87458a341bae29a4f772b0af5d97b4bfc2da3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6343
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Fix the remaining Yoda conditions, detected by checkpatch but not
fixed automatically.
While there, apply minor style changes.
Change-Id: I6e1978b89c4d56a20aceaeb2b52968eb6384432a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6356
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
There are ~900 Yoda conditions to be aligned to the coding style.
For recurrent Yoda conditions it's preferable using a trivial
script in order to minimize the review effort.
E.g. comparison of uppercase macro/enum with lowercase variable:
- ...(ERROR_OK == retval)...
+ ...(retval == ERROR_OK)...
Patch generated automatically with the command:
sed -i \
's/(\([A-Z][A-Z0-9_]*\) \([=!]=\) \([a-z][a-z0-9_]*\))/(\3 \2 \1)/g' \
$(find src/ -type f)
While there, remove the braces {} around a single statement block
to prevent warning from checkpatch.
Change-Id: If585b0a4b4578879c87b2dd74d9e0025e275ec6b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6354
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Convert to lowercase the name of arrays.
Convert to macro two uppercase const variables.
Change-Id: Ic6f5cad38722dfdf78d662ff4893e94482ab423d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6348
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
Uppercase symbols are normally used for macro or enum's values.
Convert the uppercase const variables to macros.
Change-Id: I749544c2e5deba65583824a7c2a6023e697714df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6346
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Uppercase symbols are normally used for macro or enum's values.
Convert the uppercase const variables to macros.
Change-Id: I4ba47ce2d3183b50730c5a9a265f274c7b802519
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6345
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: Iec58f7fe1d65f621ae0c841b5e25ef222885792b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6341
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
Use a command group 'ftdi' with subcommands instead of individual
commands with 'ftdi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I93a0ae7070226cd2fdea566effeb14a141269de8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6332
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Added support for reading and writing 64-bit data items
using TCL commands "mem2array" and "array2mem". Until now,
data items only up to 32 bits were supportd.
- Cleaned up functions target_array2mem() and
target_mem2array(), especially data types of variables
and variable declarations (scope).
Change-Id: Ia0ba427804f8fd8d7568f12714ab36984d6d5e24
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6286
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This change fixes behavior of the SEMIHOSTING_SYS_CLOSE operation.
It ensures that OpenOCD's own stdin/stdout/stderr streams are never
closed, not even if the target requests it via semihosting.
Change-Id: Ia85af5963d1a3516284fd834f7197369a8fb268c
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6291
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Capture the value of "errno" in semihosting isatty() call,
as is done in other syscalls.
Change-Id: I41b72175635f06c000536f583e3efa30fb57379e
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6292
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If not implemented, these specify to regular target read/write. However,
if individual threads in an RTOS can have different address translation
configured then the RTOS support can use this to do the right thing.
Use this in hwthread, where of course address translation can be set up
differently for different real cores.
Change-Id: I62c501cff1f863d855ee197dee7b73204ea8885a
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6327
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- In "reg" TCL command handler, the return value of register get()
and set() callbacks must be checked, in the same manner as it is
done in e.g. gdb_set_register_packet() or gdb_get_register_packet().
- Minor cleanup of variable definitions in the "reg" command
handler.
Change-Id: I8c57e7c087fe31d1abffa3c4d1f79a01af4c9c97
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6293
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Convert CamelCase enum in uppercase and the other symbols in
lowercase.
Change-Id: I141c55bdfe6ef2a2da28d1da15a283a644ae7cb2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6306
Tested-by: jenkins
Only one exported symbol from eCos is included in this patch.
The eCos code is left untouched to prevent conflicts with patches
currently under review.
While there, remove an unused camelcase macro
Change-Id: I8d22dec6e243c00665d99a8b8ba00474b4f088db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6305
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The eCos code is not part of this patch to prevent conflicts with
patches currently under review.
Change-Id: I71369165f2eef419b83a79ffcff50287f77949c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6304
Tested-by: jenkins
No cross dependency, just changes internal to each file/function.
Change-Id: I04153a5720b0540bc1998bafe526d523b2ee5515
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6303
Tested-by: jenkins
No major cross dependency, just changes internal to each file or
function.
Change-Id: Ie6258a090ce53de5db65df6a77d57ac6bb899488
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6301
Tested-by: jenkins
No cross dependency, just changes internal to each file/function.
Change-Id: I16568ddcd8304f5e6748c2e19f32421b047b0357
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6300
Tested-by: jenkins
Each driver is almost self-contained, with no cross dependency.
Changing symbol names in one drive does not impact the other.
Change-Id: Ic09f844f922a35cf0a9dc23fcd61d035b38308b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6299
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The struct cfi_spansion_pri_ext has few symbols in CamelCase.
Change all them accordingly to OpenOCD coding style.
Patch created automatically with the script below:
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
VppMin vpp_min
VppMax vpp_max
TopBottom top_bottom
TmpBlkUnprotect tmp_blk_unprotected
SimultaneousOps simultaneous_ops
SiliconRevision silicon_revision
PageMode page_mode
EraseSuspend erase_suspend
BurstMode burst_mode
BlkProtUnprot blk_prot_unprot
BlkProt blk_prot
EOF
) | while read a b; do
sed -i "s/$a/$b/g" src/flash/nor/*cfi*
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I135331539ca9aa84765fdffc51c87a07a46ee77a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6298
Tested-by: jenkins
The current implementation fails due to the assert() statements in
get_stm32l4_rev_str() and get_stm32l4_bank_type_str(). Rearrange the
code in order to fix the problem.
Change-Id: If19c648dec8ddd3ef2fb801150114104b34c3bf2
Signed-off-by: Marc Schink <dev@zapb.de>
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Reviewed-on: http://openocd.zylin.com/6326
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The HLA target is not anymore used by ST-Link only, but required
by Nu-Link and TI-ICDI too.
Rename the flag 'stlink' as 'is_hla_target'.
Change-Id: Id2ee2c0a1e8bf1f1e899f7a560140c34eefeeee5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6206
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This fixes 'dead assignment' bugs identified by the clang static analyzer.
Change-Id: I140ed55f0043e06a533f45f50a36887614585b04
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6323
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In these drivers we read CPUID to check the Cortex-M PARTNO,
but now the PARTNO is stored in struct cortex_m_common.core_info.
Change-Id: I5bb3b95210ab6e23b8e1252686dd81015740bf68
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6240
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Rework core detection by adding cortex_m_partno enum to detect all CPUs
using the same method.
Instead of checking the core PARTNO then assign the arch, use the stored
information within cortex_m parts[] with the flags inside which can help
simplifying a bit the cortex_m_examine code.
This change fixes:
- the Cortex-M1 detection as ARMv6-M Core (was managed as ARMv7-M)
- the displayed CPU name for Cortex-M0+ (was displayed Cortex-M0)
Change-Id: I40b6e03f7cf3664c85e297adfc25323196dfe90b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6233
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In target/arm.h the struct arm do contain 3 flags to retain architecture
version for some tweaks.
The proposal is to have only one enumerated flag 'arch' for the same purpose.
Change-Id: Ia5d5accfed8158ca21eb54af2fdea8e36f0266ae
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1) The API of "info" callback in "struct flash_driver" has been
improved. Fixed buffers for strings
2) Removed the calls to snprintf() from the flash_driver.info
implementations. Many of them were used in an unsafe manner
(buffer overruns were possible).
Change-Id: I42ab8a8018d01f9af43c5ba49f650c3cb5d31dcb
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6182
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change 7dd323b26 reduced remote bitbang performance a lot. This change
gets most of that performance back again, by reintroducing a write
buffer.
Performance numbers collected using DebugBreakpoint test from
riscv-tests/debug against a single 64-bit spike (RISC-V simulator)
instance. (Ubuntu 20.04.2, AMD Ryzen 5 3600)
Before Windows support was added: 3.09s
After Windows support was added: 12.67s
After this change: 4.69s
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I72ff4912cbbf316a30ef065e5b8f461a555f06cc
Reviewed-on: http://openocd.zylin.com/6283
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The special .DELETE_ON_ERROR deletes the target file on recipe error.
Otherwise, an incomplete output file may be considered up to date
the next time around. .DELETE_ON_ERROR provides reasonable
protection at virtually no cost.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: I67dca47ae5ddf3786993c87b9991b3046a85f00b
Reviewed-on: http://openocd.zylin.com/6235
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
Autoconf generates several files in root folder of the project.
Keep the root folder cleaner by specifying subfolder 'build-aux'.
Align .gitignore accordingly.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: Ied87faba495d9eeb8f98e78c2e2b7e7e596febfb
Reviewed-on: http://openocd.zylin.com/6236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Preprocessor directives like "#if SYMBOL" silently replace undefined or
misspelt symbols with 0, which makes configuration bugs hard to spot.
Compiler flag "-Wundef" prevents such errors.
Change-Id: I91b7ba2db02ef0c3c452d334601c53aebda4660e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6238
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
this commit extends the existing snapshot action to create a release named
'latest' with the built binaries for windows.
this 'latest' release will be updated after every push to github.
Change-Id: I75a64c598169241743add3ac9aa7a0337fbab7f2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6127
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
The early documentation for armv8a report the debug register WFAR
as containing the address of the instruction that triggered the
watchpoint. More recent documentation report the register EDWAR as
containing the data memory address that triggered the watchpoint.
The name of macros CPUV8_DBG_WFAR0 and CPUV8_DBG_WFAR1 is not
correct as they point to the debug register EDWAR, so reading such
register returns directly the data memory address that triggered
the watchpoint. The code incorrectly passes this address value to
the function armv8_dpm_report_wfar(); this function is supposed to
adjust the PC value, decrementing it to remove the effects of the
CPU pipeline. This pipeline offset, that has no meaning on the
value in EDWAR, caused commit 651b861d5d ("target/aarch64: Add
watchpoint support") to add back the offset while comparing the
address with the watchpoint enabled.
The upper 32 bits of EDWAR are not valid in aarch32 mode and have
to be ignored.
Rename CPUV8_DBG_WFAR0/1 as CPUV8_DBG_EDWAR0/1.
Remove the function armv8_dpm_report_wfar().
Remove the offset while searching the matching watchpoint.
Ignore the upper 32 bits of EDWAR in aarch32 mode.
Fix a comment and the LOG text.
Change-Id: I7cbdbeb766fa18e31cc72be098ca2bc501877ed1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6205
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
The field 'wp_pc' was originally introduced in commit 55eeea7fce
("ARMv7a/Cortex-A8: report watchpoint trigger insn") in end 2009
to contain the address of the instruction which triggered a
watchpoint. Later on with commit 651b861d5d ("target/aarch64:
Add watchpoint support") it has been reused in to hold directly
the memory address that triggered a watchpoint.
Rename 'wp_pc' as 'wp_addr' and change its doxygen description.
While there, fix the format string to print the field.
Change-Id: I2e5ced1497e4a6fb6b38f91e881807512e8d8c47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6204
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Compile fails with error:
src/jtag/drivers/cmsis_dap.c:683:28: error: format specifies type
'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
" received 0x%" PRIx8, CMD_DAP_TFER, resp[0]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
Fix the format specifier.
Change-Id: I0a5a1a35452d634019989d14d849501fb8a7e93a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6255
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
The workaround for jimtcl 0.80 in commit 36ae487ed0 ("jimtcl:
add temporary workaround for memory leak in jimtcl 0.80") issues a
compile time error on macOS:
../src/helper/command.c:157:22: error: aliases are not
supported on darwin
__attribute__((weak, alias("workaround_createcommand")));
The OS is x86_64-apple-darwin19.6.0 and the compiler used is
x86_64-apple-darwin13.4.0-clang.
Restrict the workaround on Linux host only. The fix for 'expr'
syntax change is already merged and the workaround will be dropped
soon.
Change-Id: I925109a9c57c05f8c95b70bc7d6604eb1172cd79
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adam Jeliński <ajelinski@users.sourceforge.net>
Fixes: 36ae487ed0 ("jimtcl: add temporary workaround for memory leak in jimtcl 0.80")
Fixes: https://sourceforge.net/p/openocd/tickets/304/
Reviewed-on: http://openocd.zylin.com/6241
Tested-by: jenkins
Both GDB commands "target remote" and "target extended-remote" require
to have ":" right before port number.
e.g.
(gdb) target extended-remote :3333
Add ":" to the warning message so that users can copy & past it.
Change-Id: Id6d8ec1e4dfd3c12cb7f3b314064f2c35fa7ab55
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6237
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
this change aims to provide a better gdb debugging experience,
by making gdb understand what's really happening.
before this change when hitting a watchpoint
- openocd reports "T05" to gdb
- gdb displays: Program received signal SIGTRAP, Trace/breakpoint trap.
after the change
- openocd reports "T05watch:20000000;" to gdb
- gdb displays:
Hardware watchpoint 1: *0x20000000
Old value = 16000000
New value = 170000000
...
Change-Id: Iac3a85eadd86663617889001dd04513a4211ced9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6181
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a use of AH_BOTTOM from configure.ac. This macro is used by
autoheader to add '#include' of some include file to the end of
config.h.in and then to config.h. OpenOCD can be built with a custom
config.h, so it's preferable to move these '#include' statement directly
in the C files that need them dropping this unneeded dependency.
It also causes problems when I want to use the gnulib library (which
comes with its own Makefile, and does not have the same include path as
the top-level Makefile).
So this change touches a lot of files, but is actually really simple. It
does not affect functionality at all.
Change-Id: I52c70bf15eb2edc1dd10e0fde23b2bcd4caec000
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6171
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Currently, all drscan commands will cycle through DR-PAUSE before reaching
TAP-IDLE. This patch provides a different path on FTDI driver.
This change is required for the ST On Chip Emulator (OnCE), to avoid
re-enabling the OnCE tap after every DRSCAN. This is because the OnCE
TAP (see ST Application Note AN4035) gets disabled if DR-PAUSE is entered
before DR-UPDATE.
With this commit, the current path:
DR-SHIFT -> DR-EXIT1 -> DR-PAUSE -> DR-EXIT2 -> DR-UPDATE -> IDLE
is changed to:
DR-SHIFT -> DR-EXIT1 -> DR-UPDATE -> IDLE
only if IDLE is the endstate (which is the driver default).
Before this patch, once the SHIFT sequence is complete, the driver would
normally move to the nearest stable state, which is DR-PAUSE, by clocking
out a '10' binary sequence. Then it would follow the path provided by
tap_get_tms_path() to reach endstate. It is done this way because
tap_get_tms_path() only supports stable states.
After this patch, the strategy is mostly the same, with the exception that,
if TAP_IDLE is the endstate, a '110' binary sequence is output after completing
the SHIFT sequence. This takes the TAP directly to IDLE, with no further action
required.
A scheme of the DR chain is shown below. A * character is used to mark the
stable states.
----------------------------------------------------------------------
| | 0
v 1 0 0 1 0 1 1 |
IDLE* -> SEL-DR -> CAPTURE -> SHIFT* -> EXIT1 -> PAUSE* -> EXIT2 -> UPDATE
| ^
1 | |
-----------------------------
Change-Id: Ib413e5c4c0bbf75dae0b4672119bae4ef03d0258
Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Reviewed-on: http://openocd.zylin.com/6123
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
auto-completion behavior:
- if there is only one matched command complete the user-command
- else if multiple matches add the common part then in second step
list all matched commands
- sub-commands are handled in the same way
- auto-completion restarts after these characters ';', '[', '{'
Change-Id: I1b81dd19191a5785e68d0bb5cd244e01a4dd0587
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6095
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation of Jim_SetResultFormatted() reports that the jim
objects passed as arguments would be freed if have zero refcount.
Remove the useless Jim_IncrRefCount()/Jim_DecrRefCount().
Remove the dangerous Jim_FreeNewObj() that should trigger a double
free(). Not tested due to lack of aice adapter.
While there, rename some CamelCase symbol.
Change-Id: Ic56704c83d6391c38f6b0efa6566784d453bc0fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6190
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 7a731eb637 ("Added HostOS variable"), merged in 2009,
adds a TCL global variable 'ocd_HostOS' that reports in a string
the OS of the host.
This was proposed as a workaround for jimtcl that didn't define
the standard TCL variable 'tcl_platform(os)'.
With commit 42f3fb7b7f46 ("Determine platform_tcl() settings with
configure"), merged in 2010 and part of jimtcl 0.70 issued in
early 2011, jimtcl provides the requires TCL standard variable
'tcl_platform(os)'.
The variable 'ocd_HostOS' has never been used by any TCL script
distributed with OpenOCD.
Drop the TCL variable 'ocd_HostOS'.
Change-Id: I27858de35cc9d30df97145ca1ccd24877be4af11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6189
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If malloc() fails, the just allocated Jim_Obj will leaks.
Move Jim_IncrRefCount() before the malloc() and deallocate the Jim
object with Jim_DecrRefCount() on malloc() fail.
While there, add the 'out of memory' log and fix the CamelCase
name of the symbol tclOutput.
Change-Id: Ic733db229d5aa5d477d758ea9cb88cd81d7542cd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6188
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The files jim-nvp.[ch] were originally inside jimtcl, then in 2011
they were dropped by jimtcl and integrated in OpenOCD.
The initial purpose was to make them as an independent library,
thus the presence of an 'init' function. Being now part of OpenOCD
do not require the 'init' function anymore, that is still empty
and unused, plus its name is in violation of the coding style.
Drop the function Jim_nvpInit().
Change-Id: I429e10444c86a26dbdc22aa071315324dc5edc3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6187
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Accordingly to OpenOCD coding style, both typedef and Camelcase
symbols are forbidden.
The type '_Bool' is not used in the code, having 'bool' as
preferred choice.
Remove the definition of '_Bool' from 'types.h'.
Change-Id: I8863f9836ccd9166e0c69fa5d75d6fef79ae7bfb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The ELF typedef's 'Elf32_Sword' and 'Elf32_Hashelt' are not used
within OpenOCD. Plus, being their name in CamelCase require extra
effort to include them in the exceptions for checkpatch.
Remove the unused typedef's.
Change-Id: I18f039567edd5b24dbb41df5406c154f31022ae7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6178
Tested-by: jenkins
Reviewed-by: Christian Hoff <christian.hoff@advantest.com>
The existing code asserted in that case, which is not correct. This
would allow the user to crash OpenOCD with a bad ELF file, which is
not what we want. A proper error should be reported in that case and
OpenOCD should not crash.
Change-Id: Ied5a6a6fd4ee0fd163f3fe850d304a121ecbe33a
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/6172
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Libusb defines both the struct and a typedef to the struct using
the same struct name. It's then possible to use either 'struct x'
and 'x'. E.g.:
typedef struct libusb_device libusb_device;
OpenOCD is not consistent and uses a mix of 'struct x' and 'x'.
To make OpenOCD code uniform, stick at project's coding style and
use 'struct x' in place of the typedef'd name.
Change-Id: I901458b680e42830d3f371e47997157f91b7f675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6165
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit a7d68878e4 ("helper/command: unregister commands through
their full-name") introduces for the first time in OpenOCD the use
of jimtcl API Jim_DeleteCommand().
The prototype of Jim_DeleteCommand() has changed with jimtcl 0.80
and the current code doesn't build with jimtcl 0.79 or older. This
is an issue for those distributions, like Debian, that provide
jimtcl as a separate package/library and have not switched yet to
the new jimtcl version.
Add a compile-time condition to cope with the jimtcl API change.
Change-Id: Ic813ab7c0ebd3c8772f27775ba3912a47d5c275c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: a7d68878e4 ("helper/command: unregister commands through their full-name")
Reviewed-on: http://openocd.zylin.com/6191
Tested-by: jenkins
fix the warning below by adding a '.' after xref in line 10184:
./doc/openocd.texi:10184: warning: `.' or `,' must follow @xref, not c
Change-Id: Ibd976ae61cf6845e925b839321444dcb25a3c04a
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix the warning below by adding a '.' after xref in line 4517:
../code/doc/openocd.texi:4517: warning: `.' or `,' must follow @xref, not )
Change-Id: I6e529c7e83c9f912e1dd899abf5f630c90b583d9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6174
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Uses CMSIS-DAP v 1.2 or higher protocol command DAP_SWD_Sequence
to write to DP TARGETSEL register. This write is not acknowledged
by device so we cannot use standard DAP_Transfer
Change-Id: Ib252d09570bcc2282be5f854e0ab9a0dfda06189
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6117
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
This file has been added to OpenOCD 0.5.0 in 2011, before gerrit
gets in use, with commit ba71e8c521 ("at91: add chip register
definition and generic init support").
The only procedure in the file has never been referenced in any
other part of OpenOCD. This procedure has syntax errors while uses
its argument 'cs' and several unmatched parenthesis, which clearly
highlights that it has never been used so far.
Gerrit does not report any patch aimed at fixing it.
Even if the file seems unused and could be removed, let's fix it
in the hope it could get used.
While there, remove some useless parenthesis and format it using
the new simplified syntax required by jimtcl 0.81.
Change-Id: Ied26456262e7b99de37667a8ce418f4f12e237bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ba71e8c521 ("at91: add chip register definition and generic init support")
Reviewed-on: http://openocd.zylin.com/6157
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The mode of command 'ftdi_layout_signal' is set to COMMAND_ANY in
[1] and the command has no constraints that limits its use to the
config phase only.
But [2] documents it as '{Config Command}'.
Update the documentation to report the correct mode '{Command}'.
[1] commit f5e97b5e1b ("Add FTDI JTAG driver using MPSSE layer")
[2] commit 76afadeb7b ("doc: Add documentation for the ftdi driver")
Change-Id: I6b14aebb98e48f7080c585f3df881714bb188af0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6155
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The command 'ftdi_location' is deprecated and a TCL procedure is
in place to direct the user to the replacement command.
There is no need to document the deprecated command.
Remove 'ftdi_location' from the documentation.
Change-Id: Ia431c6b0e7444d3f3288c088429bfb47089ff1b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6154
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Some command that is only valid during configuration is documented
as generic command.
Annotate them as {Config Command} in the documentation.
Change-Id: Ifdbb6ec89b945e3d7adce94af379d94f511a64b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6153
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Commit 246782229f ("smp: replace commands smp_on/smp_off with
"smp [on|off]"") deprecates some multi-word comments, when openocd
was unable to properly handle mixes of multi-word commands and tcl
procedures having a common initial word.
This limitation is over, so move in startup.tcl the multi-word
commands deprecation, making it easy to remove them after a grace
period.
Change-Id: Icb550d1fa7559b95692d2a1244880da6c90ec0b2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5677
Tested-by: jenkins
Windows socket descriptor is not file descriptor, so when
using remote_bitbang on Windows, it fails with "fdopen:
failed to open write stream".
This patch removes the file write stream, replaces it
with socket write calls.
Change-Id: Ifd7c8a4139a5ac51ecd2846835a7a947a90fe16c
Signed-off-by: Yun Liu <liuyun.97@gmail.com>
Reviewed-on: http://openocd.zylin.com/6096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some CMSIS-DAP adapters keep buffered packets over
USB close/open so we need to flush up to 64 old packets
to be sure all buffers are empty.
Flush just after cmsis_dap_open() and in the case of command mismatch.
Change-Id: If21a118639e64d90635b4ecf81013d29a7b9f78d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6135
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Check returned HID report number (or the first byte of returned
bulk packet) which should be equal to the issued command or 0xff
in case of the command is not implemented.
Fix error return paths in cmsis_dap_init() to clean up the adapter
connection.
Don't fail cmsis_dap_init() when an unimportant function fails
(for the case the adapter doesn't implement some parts of protocol).
Change-Id: Ief8382aabe9915346b2273702fb2ff17bbb5eb1b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6121
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
The function's name was consistent with its purpose to handle
commands that were not at root level, thus not directly 'known'
by jimtcl.
Rename it as jim_command_dispatch() to highlight that now it is
a jim_handler and its purpose is to dispatch the call to the
proper command handler.
Change-Id: I9491a6d6459b8eb37a6c402abcae08388c693764
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5791
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that all commands are executed through the common handler
command_unknown(), the message about command execution is logged
by command_unknown(). There is no need, for "native" commands
(.jim_handler) at root level to log the message (again) by itself.
Remove calls to script_debug() apart from command_unknown().
Make script_debug() static as only used in command.c.
Change-Id: I9b2728b69e7643d6121c4b35a96bc825bcb5488d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5676
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
There is no need anymore to keep alive the tree of struct command.
Remove it and let jim to free() the command's struct command that
is referenced through command's private data.
Change-Id: I2cd84e0274a969ce200320e3a177ac20c7823da0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5675
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While keeping the struct command in place, unregister the jim
commands by scanning the list of jim commands through their
full-name.
Change-Id: I0e903fbc31172858b703d67ccd471809c7949e86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5674
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that every command has struct command as private data, use jim
to get access to the struct command to read the command mode,
instead of running through the tree of struct command.
Change-Id: Iddacdbac604714f6abe38a050daad245bdcfd20c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5673
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that the commands are registered using their full-name, the
full-name is in argv[0].
Don't rebuild the full-name but use directly argv[0].
Change-Id: Ic9e469ac39276367b8c47527e70791ff470fefbc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5672
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The current implementation of "help" related commands is tightly
connected to the tree of struct command.
The TCL commands 'add_usage_text' and 'add_help_text' have to add
fake commands in the tree of struct command to handle the help of
TCL procs.
Move all the help texts in a list accessible from the struct
command_context and register the commands through their full name.
Keep the list sorted alphabetically by the command name, so the
result of commands 'help' and 'usage' will be sorted too.
Remove the associated help and usage during commands un-register,
but call help_del_all_commands() for the text added through TCL
commands 'add_usage_text' and 'add_help_text'.
The resulting help and usage output is not changed by this patch
(tested on all the help and usage strings in current master
branch).
Change-Id: Ifd37bb5bd374cba1a22cd7aac208505b4ae1e6fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5670
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A tcl proc can be executed anytime, in any command mode.
Let the command "command mode" to detect a tcl proc and return the
string "any".
Change-Id: I0559076c3063632ee0ea9a57a25f91060209b77f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5669
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Replace the "struct command *parent" parameter with a string that
contains the command prefix.
This abstracts the openocd code from the knowledge of the tree of
struct command.
This also makes unused the function command_find_in_context(), so
remove it.
Change-Id: I598d60719cfdc1811ee6f6edfff8a116f82c7ed6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5668
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In current code the current target is overridden whenever
jim_handler_data is not NULL. This happens not only with target
prefixed commands, but also with cti, dap and swo/tpiu prefixed
commands.
While this is not causing any run-time issue, by now, the
behaviour is tricky and makes the code cryptic.
Add a specific field to struct command for the target override so
the content of jim_handler_data can be restricted to command
specific data only (today only cti, dap and swo/tpiu).
Extend the API register_commands() to specify the presence of
either the command data or the override target.
The new API makes obsolete calling command_set_handler_data() to
set jim_handler_data, so remove it.
Change-Id: Icc323faf754b0546a72208f90abd9e68ff2ef52f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5667
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that target override is uniformly implemented for all types of
commands, there is no need for target-prefixed "native" commands
(.jim_handler) to sneakily extract the overridden target from the
struct command.
Modify the commands to use the standard API get_current_target().
Change-Id: I732a09c3261e56524edd5217634fa409eb97a8c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5666
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Today openocd registers the commands to jim with three methods:
1) "native" commands (.jim_handler) at root level are registered
directly as jim commands;
2) "simple" commands (.handler) at root level are registered
through the handler script_command();
3) all other commands not at root level are registered through the
handler command_unknown().
Apart from using different handler, other inconsistencies are
present:
a) command in 1) are not checked for their "mode", so are run with
no check about current mode (COMMAND_CONFIG or COMMAND_EXEC);
b) target_call_timer_callbacks_now() is called only for "simple"
commands and not for "native" commands;
c) target override is performed only for "simple" commands and not
for "native" commands.
Drop script_command() and extend command_unknown() to uniformly
handle all the cases above, fixing all the inconsistencies already
mentioned.
The handler's name command_unknown() is probably not anymore
appropriate, but will be renamed in a separate change.
Note: today all the commands in a) have mode CONFIG_ANY, apart for
"mem2array" and "array2mem" that have mode COMMAND_EXEC. But the
latter commands are registered during target init, so do not exist
during COMMAND_CONFIG and no issue is present.
Change-Id: I67bd6e47eb2c575107251b9192c676c27d4aabae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5665
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While registering a new command, jim accepts a pointer to command's
private data that will be accessible during the command execution.
Today openocd is not consistent and passes different private data
depending on the command, and then even overwrites it:
- "simple" commands (.handler) are registered with their own
struct command pointer as command private data;
- "native" commands (.jim_handler) at root level are registered
with NULL command private data;
- "native" commands (.jim_handler) not at root level are
registered with the struct command pointer of their root command
as command private data but, when executed, the command private
data is overwritten by the value in field jim_handler_data taken
from their struct command.
Uniform the usage of command private data by always set it to the
struct command pointer while registering the new commands.
Note: for multi-word commands only the root command is registered,
so command private data will be set to the struct command of the
root command. This will change later in this series when the full-
name of the command will be registered.
Don't overwrite the command private data, but let the commands that
needs jim_handler_data to get it directly through struct command.
For sake of uniformity, let function command_set_handler_data() to
set the field jim_handler_data also for "group" commands, even if
such value will not be used.
Now Jim_CmdPrivData() always returns a struct command pointer, so
wrap it in the inline function jim_to_command() to gain compile
time check on the returned type.
While there, uniform the code to use the macro Jim_CmdPrivData()
to access the command's private data pointer.
Change-Id: Idba16242ba1f6769341b4030a49cdf35a5278695
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5664
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I41a8447d487ec8f6f32c2babcbc73ac21c769344
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6152
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every Command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I797e8d9f5ab0aa1936f350b340d3bdd52373f5aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6151
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Both 'Command' and '{Command}' are in use, with the following
statistics:
0 @deffnx {Command}
45 @deffn {Command}
31 @deffnx Command
382 @deffn Command
While 'Command' is the most popular, prefer the version within
curly-brackets that has to be used for multi-word definition like
'{NAND Driver}', '{Config Command}', '{FPGA Driver}', ...
Patch generated through:
sed -i 's/^\(@deffn \)\(Command\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx \)\(Command\)/\1{\2}/' doc/openocd.texi
Change-Id: If692bbf7e546c5287f466a6aa6940d42b3d4655d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6150
Reviewed-by: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: jenkins
The commit 5280eb618a fixed all `adapter_khz` and
`adapter_nsrst_*` commands in the doc but missed grouping them. This
let the commands `adapter speed`, `adapter srst pulse_width`, and
`adapter srst delay` not indexed.
Tell texinfo about adapter sub-commands by grouping them in one.
Change-Id: Ida53c4f5cfe28827320c145c8d501d53e831623c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6134
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
There are some breakpoint/watchpoint related code in armv8_dpm.c,
but seems not working for aarch64. Target aarch64 has its own
breakpoint implementation in aarch64.c. This commit follows the
same logic to add watchpoint support for target aarch64.
This commit also increases the size of stop_reason[] in function
gdb_signal_reply() since the old size is too small to fit in a
64-bit address, such as ffff8000115e6980.
Change-Id: I907dc0e648130e36b434220f570c37d0e8eb5ce1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/4761
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Kevin Burke <kevinb@os.amperecomputing.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The comments currently used are not rendered.
Change-Id: I3fcfb6aee4dea9c4f9186a7aec70d382a1abd634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6133
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add a file to the LICENSES directory to describe how file licenses
should be described in all the OpenOCD files, using the SPDX
identifier, as well as where all licenses should be in the source
tree for people to refer to (LICENSES/).
This file is mainly copied from the Linux kernel file in
Documentation/process/license-rules.rst
originally written by Thomas Gleixner <tglx@linutronix.de>, with
specific adaptations for OpenOCD.
Change-Id: I7a98fc756df90dc86dbc6e0c47c009a610a0318d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5973
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The documentation of OpenOCD is released under the GNU Free
Documentation License, version 1.2, with embedded some part of
OpenOCD code released under the GNU GPL-2.0-or-later.
Update doc/fdl.texi with latest minor fixes as in
https://www.gnu.org/licenses/old-licenses/fdl-1.2.texi
Update doc/openocd.texi and move here the license chapter title
Add license file LICENSES/preferred/GFDL-1.2 from
https://www.gnu.org/licenses/old-licenses/fdl-1.2.txt
and add the required tags for reference and tooling, coping
mostly from the Linux kernel license file in the 'deprecated'
folder.
Add a readme file to link to the existing texinfo copy of the
license.
Change-Id: Ief96e0686257be7a70d4eeec442848bd6494763d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5969
Tested-by: jenkins
The stand-alone application "contrib/itmdump.c" is released as
GPL-3.0-or-later.
Add GPL-3.0 license in the licenses list.
Copy in subfolder stand-alone the GPL-3.0 from
https://www.gnu.org/licenses/gpl-3.0.txt
adding the header required by spdxcheck.py.
Change-Id: I238efc411e07ed6bc1eba23edbc91b3825c3d2c7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5968
Tested-by: jenkins
The script spdxcheck.py (used by checkpatch.pl) searches for the
license files in a dedicated folder, split in the subfolders:
"preferred", "dual", "deprecated", "exceptions".
Move the GPL-2.0 license from COPYING to the subfolder preferred,
adding the header required by spdxcheck.py.
The header is copied from equivalent file in the Linux kernel,
made by Thomas Gleixner <tglx@linutronix.de>.
Note: the license in COPYING matches exactly
https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
Add a minimalist COPYING in the top directory, as required by
automake, pointing to the files in LICENSES.
Change-Id: I1fd0abc57b554d74f0b00fabd6c8c822b2c4acb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5967
Tested-by: jenkins
Each one of CMSIS-DAP command handlers was responsible for setting
HID report number, which in case of USB bulk transport was not used
at all. The command had to be filled with 1 byte offset whereas
the response was read without an offset.
Introduce 'command' and 'response' pointers into struct cmsis_dap.
Use them for filling the command and read the response respectively.
CMSIS-DAP command parameter are now at positions as documented in
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__Commands__gr.html
Adjust buffer allocation for HID and USB bulk transports.
While on it, use h_u32_to_le() and h_u16_to_le() instead of per-byte
writes.
Change-Id: Ib0808d6826ba0e254c1007ace8b743405536332a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6120
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: Idef0b6cf10fab583bc8d13b3b4fadd5cc368c090
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5990
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: I3f334f2d02515d612097955e714910a587169990
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5992
Tested-by: jenkins
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
All ftdi devices require a dedicated line in the udev rules, but
some USB VID/PID present in interface and board config file is
missing in udev rules.
Add the missing ftdi devices in udev rules.
Change-Id: I850a4a95a2d4bb63b3fd09be803be8c23c4d6b49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6101
Tested-by: jenkins
The API Jim_CreateCommand() in latest version of jimtcl leaks the
memory allocated internally by jimtcl when it converts the string
command-name to a Jim_Obj.
The fix is already merged upstream and would be available in next
jimtcl 0.81, expected in ~6 months, hopefully before the next tag
for OpenOCD v0.12.0.
OpenOCD v0.11.0 is distributed with jimtcl 0.79.
Debian distributes jimtcl as a separate library package and today
it's still on 0.79.
It make sense to keep using jimtcl 0.80 in current development
cycle to test it further. But having this background memory leak
noise hides the eventual new memory leaks that could come from the
development activity.
This patch uses the internal jimtcl API Jim_CreateCommandObj() and
correctly free the internal object, avoiding the memory leak.
Being an internal API, it is not accessible if OpenOCD is linked
with an external jimtcl library. Nevertheless, building jimtcl as
a submodule of OpenOCD makes the trick effective.
The scope of this patch is thus limited at developers that build
OpenOCD with jimtcl submodule and need to control and debug memory
leaks.
This patch is supposed to be removed as soon as jimtcl 0.81 gets
available.
The added code is located, on purpose, in an area of the file that
hopefully will not conflict other patches pending in gerrit.
Change-Id: I4d300ad21bdb6c616c3f0f14b429b4fdf360900d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
After bootstrapping build, if we want to do an out-of-tree build (ie: in the
OOT-build dir) we have a build failure because build system relies on
the OOT-build/src directory exists
```sh
./bootstrap
mkdir OOT-build
cd OOT-build
../configure --disable-dependency-tracking --<flag1> --<flag2> ...
make
$ LANG=C make
cat ../src/helper/startup.tcl ../src/jtag/startup.tcl ../src/target/startup.tcl ../src/server/startup.tcl ../src/flash/startup.tcl | ../src/helper/bin2char.sh > src/startup_tcl.inc || { rm -f src/startup_tcl.inc; false; }
/bin/bash: line 1: src/startup_tcl.inc: No such file or directory
make: *** [Makefile:6603: src/startup_tcl.inc] Error 1
```
These kind of errors are fixed indicating relevant directory creation in
Makefile.am before actually relying on it.
Change-Id: I8185fd41ef942184597dc4c0092796034572cbe1
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6106
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 4c00f96fc2 ("configure.ac: switch to autoconf 2.69")
changes the required minor version of autoconf.
Update the README file accordingly.
Change-Id: I98b32b888ff531300f03c4ef9ebcbf8110509e52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6114
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
In case of some error, the USB device and firmware file are still
claimed. Make sure refcounting is properly accounted for both cases.
Change-Id: I933114f68e59280e58372c0941a0062fe96ab340
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/6115
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For Zephyr rtos support it is necessary to define general register
numbers for architecture. There were some already in arc.h file.
Let's define ARC registers numbers as a set instead of separate defines.
Change-Id: I63742b8608f9556c2ec9bd2661a0fd9cf88e9b74
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/6105
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Support halting the CPU directly after a reset. If halt is
requested, the CPU stops directly at the reset vector, before
any code is executed.
This functionality was implemented using the Reset Catch
debug event.
Change-Id: If90d54c088442340376f0b588ba10267ea8e7327
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/5947
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With zy1000 removed, there is no other implementation that uses
the minidriver, apart from the test/example minidriver-dummy.
While the idea of the minidriver is probably still valid (that is
to intercept jtag primitives before serialization), there is no
current use case, no guarantee it is really working, and the way
it was implemented (by macros and #if conditionals) is really hard
to maintain and test.
Let's let it rip in git history, from where it could eventually be
taken back in a more modern implementation.
The entry points of minidriver API are still in the code with the
original names.
Change-Id: I882e32cb26cf5842f9cba14e3badaf8948e3760d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6091
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The code for ioutil has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I36dce1669ebe9acada5f9e752835c53e5214e3be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6089
Tested-by: jenkins
The code for oocd_trace has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I989f8345dee4ff2369bcf5e2e2ace86bbd5aa6a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6088
Tested-by: jenkins
We do not have anymore any deprecated target name.
Drop the code to handle deprecated target names and the placehold
in struct target_type.
This patch is separated from the patch that drops the remaining
deprecated target names to be ready to revert this if there is any
need in the future.
Change-Id: I96fca7ffa39d8292f81e79f115ea45c4a30035d7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some target name were marked as deprecated in release v0.7.0 and
v0.8.0, almost 7 years ago, and replaced with more 'actual' names.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.8.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the target names already deprecated in v0.8.0.
Change-Id: I7c7491496db1b302b4eb1e9fc6090b58d4acf05a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6086
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD command line flag -p/--pipe was marked as deprecated
in release v0.5.0, more than 9 years ago.
We can reasonably expect that in these 9 years any user of OpenOCD
has already migrated to v0.5.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the command line flag already deprecated in v0.5.0.
Change-Id: I2faeb592ed2c2f67c2d3227f118093e39fcf4a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6084
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm920t cp15i' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I755c4283e13e125558fcd73b15fe20498eae95ca
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6083
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm720t cp15' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I2b325d0312d96ca5e5f0f1bad13bb162b3b75c52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6082
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
OpenOCD file configure.ac requires autoconf equal or newer then
2.64, which is quite old.
These are the release dates so far:
- autoconf-2.64 2009-07-26
- autoconf-2.65 2009-11-21
- autoconf-2.66 2010-07-02
- autoconf-2.67 2010-08-02
- autoconf-2.68 2010-09-22
- autoconf-2.69 2012-04-24
- autoconf-2.70 2020-12-08
Switch to autoconf 2.69, which is old enough to be the standard in
current systems.
This should reduce the effort on configure.ac compatibility.
Change-Id: Ia7c78d2fa34c50ed5ccf4fb66ad3484369cf3b4a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6008
Tested-by: jenkins
Update jimtcl to version 0.80.
Add a workaround in Makefile.am to allow 'make distcheck' with the
new jimtcl. A fix is already merged upstream but will be part of
the future release 0.81 of jimtcl.
Change-Id: I1cebfb9c17179114960dc771e0b31836b4b9b058
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5949
Tested-by: jenkins
There is no good reason to use macros instead of static inline functions. The
current code is hard maintain. For example, it changes variables outside of the
macro scope. Also, it is conflicting with the C coding style.
Change-Id: I5ac9d2ae076ef73c176d4e32b2e7e0a99fa875ab
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The buffer passed to stlink_usb_trace_read() is allocated of size
*size and does not need to be zero-terminated. There is no reason
to not fill its last byte.
When checking the bytes available on swo, limit the retrieved byte
length to *size.
Change-Id: Iade0f8963118695931f13a8a3f1ab204911236b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6061
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Missing the space cause the hex value to be printed together with
the following field.
Add a space after PRIx32.
Change-Id: I95824a9a8b8c0ad911d6c31f732d926cb3e0c068
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6060
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
The change [1] guarantees that the value pointed by 'prescaler'
gets always set, even when the adapter does not support the
specific mode requested (e.g. sync), or during trace disabling.
This works fine with the code in armv7m_trace_tpiu_config(), but
requires all the parameters to be valid also to disable the trace
(with 'enable==false'), otherwise returns error on incorrect
parameters or even causes segmentation fault if pointers
'trace_freq' or 'prescaler' are NULL.
Another problem in stlink_config_trace(), not linked with [1], is
caused by a tentative to change the settings on an already enabled
trace; the trace is disabled before the new parameters are fully
validated and in case of invalid parameters the trace is not
re-enabled.
It would be more logical to first check all the parameters, then
disable the trace, change the settings and re-enable the trace.
Practically revert [1] by checking 'enable==false' at function
entry, then disable trace and exit without any further check on
the other parameters.
For the case 'enable==true', validate all the function parameters
then disable the trace, update the trace settings and re-enable
the trace.
Modify the caller armv7m_trace_tpiu_config() to initialize the
variable 'prescaler' to a safe value to avoid the issue targeted
by [1].
[1] commit 38277fa752 ("jtag/drivers/stlink_usb: fix SWO prescaler")
Change-Id: Ia6530682162ca2c9f5ac64301f2456f70cc07ed2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5934
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
pg315 of CoreSight Components:
It is recommended that the ITMEn bit is cleared and waits for the
ITMBusy bit to be cleared, before changing any fields in the
Control Register, otherwise the behavior can be unpredictable.
Change-Id: Ie9a2b842825c98ee5edc9a35776320c668047769
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6043
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target->endianness is initialized to TARGET_ENDIAN_UNKNOWN at 34 lines
below, before calling target_configure. This initialization is
redundant and not needed.
Change-Id: Iea2d5e17a13c1a8b0b209ba7c20043736b520ef6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The C style guide forbids typedef'd structs, see 'Naming Rules'.
Change-Id: I983dd52307136d1b5adb58d8c44c0c14422d31e2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6032
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Quote: The ST-LINK TCP server is an application to share the debug
interface of a single ST-LINK board among several host applications,
typically a debugging tool and a monitoring tool.
Note: ST-Link TCP server does not support the SWIM transport.
ST-LINK TCP server allows several applications to connect to the same
ST-Link through sockets (TCP).
To use ST-LINK TCP server:
- using stlink-dap : use 'st-link backend tcp [port]'
- using hla : use 'hla_stlink_backend tcp [port]'
the default port value is 7184
Change-Id: I9b79f65267f04b1e978709934892160e65bd2d6d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5633
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the introduced stlink_backend_s struct provides an API to separate USB
internals from stlink core.
this separation aims to ease:
- stlink-server integration [1]
- stlink driver split into modules:
- stlink_core
- stlink_usb
- stlink_tcp [1]
[1] refer to http://openocd.zylin.com/#/c/5633/
Change-Id: Iff6790942612ce1769ec4c75990914534e5e9e24
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5632
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
TCL expands the variables only if preceded by a dollar sign.
Add the missing dollar before the variable's name '_CPUTAPID'.
Change-Id: Icc5d0dddf24f75d12ee63fee69e1b265e842ca43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wes Cilldhaire <wes@sol1.com.au>
Fixes: c3166b43e4 ("tcl/target: Add QuickLogic EOS S3 MCU configuration")
Reviewed-on: http://openocd.zylin.com/6079
Tested-by: jenkins
Reviewed-by: TM <tommy_murphy@hotmail.com>
OpenOCD is based on a single main loop that schedules all the
activities.
At the execution of a TCL command, the timestamp is checked to
eventually trigger the polling of the targets. This means that by
executing a TCL command the polling can be triggered and detect a
change of target's state.
When openocd 'resumes' a target, the target can halt again by
hitting a breakpoint.
The 'resumed' event handler is started just after the target has
been resumed, but it triggers a polling before the execution of
its very first instruction.
If the polling finds the target halted, it will run the 'halted'
event handler, that will then be executed 'before' the pending
'resumed' handler.
In case of gdb, a 'continue' command will restart the target but,
polling (and halt detection) executed before the end of the resume
process will hide the halt. As a consequence, the gdb will not be
informed of the halt and will remains waiting as if the target is
still running without showing the prompt.
This can be verified by running on the target a firmware with a
loop, run openocd with a dummy 'resumed' event, and let gdb to set
a breakpoint in the loop. A 'continue' command will cause the
target to halt again by hitting the breakpoint at the next loop
iteration, but gdb will loose it and will not return the prompt.
openocd -f board/st_nucleo_f4.cfg -c \
'stm32f4x.cpu configure -event resumed {echo hello}'
arm-none-eabi-gdb -ex 'target remote :3333' -ex 'b *$pc' -ex c
Disable the polling while executing target's resume().
Document it and provide hints to developers to cope with future
implementation.
Change-Id: I3be830a8e7c2ef6278617cb4547a4d676b0ddeb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Габитов Александр Фаритович <gabitov@planarchel.ru>
Reviewed-on: http://openocd.zylin.com/6074
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Commit 4fc0f3530c ("Makefile.am: fix non-POSIX warning from
automake") uses the BSD make extension '!=' to generate the list
of files NEWS-xx, but it's not POSIX (yet), it's not backward
compatible with GNU make 3.82 (used in CentOS 7, EOL scheduled for
2024) and depending on automake evolution it could trigger again
the warning 'apparently' just fixed.
Move in configure the generation of the file list.
The only drawback is that when a developer adds a new NEWS-xx
file, he/she has to run configure again before 'make distcheck',
otherwise will get failure.
Change-Id: Ia97e7f4e612655a97702f95e8451040539659b85
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Jan Matyáš <jmatyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6054
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently wp/rwp commands fail on 64-bit targets:
> wp 0xffffffff80001400 4
addr option value ('0xffffffff80001400') is not valid
Change-Id: I94d4af906b02b7bd463c8d79a6235a3646dfc434
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-on: http://openocd.zylin.com/6058
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In case an USB location path contains path members
larger than 9. The string_length variable is regardless
decremented by 2 with assumption that the member is
one digit length. For exmaple 1-12.2 will fail.
This patch uses strlen to calculate
digits in a path member.
Change-Id: I9c26a04d0c6af13fec65157f222599497294e2b2
Signed-off-by: Krzysztof Hockuba <krzysztof@hockuba.eu>
Reviewed-on: http://openocd.zylin.com/6048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We have both the singular form, register_command(), and the plural form
register_commands().
Change-Id: I905ea83988b8ac70dd809b02d53b646aa4d66697
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6042
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The subpage "thelist" used to have a title "Pending and Open Tasks"
but the commit c41db358a0 changed it to "The List". With
@subpage, it now renders:
"The List of The List enumerates opportunities for"
instead of
"The List of Pending and Open Tasks enumerates opportunities for"
This commit fix it to
"The List enumerates opportunities for"
Change-Id: Ifee0dcd9b3c9f7e651a8748a7afda99eedea3c5c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6041
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
this fix permits to add correctly the generated artifact (windows binaries)
into the release section.
Change-Id: Ia982370d3a1e08c623ebcabb5ac97e9fb49d00e0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If user specifies a serial number for the jlink device, openocd
extends the search to network jlink devices too, without checking
if the host has a valid and functional network connection. If the
network is not functional, libjaylink returns error. This error
invalidates the discovery on USB, even if it was successful.
Factor-out parts of the jlink_init into separate jlink_open_device
function, use that function to firstly discover and match USB
devices and, if matching device was not found on the USB bus and
serial number was specified, repeat discovery and matching via TCP.
Fixes: https://sourceforge.net/p/openocd/tickets/294/
Change-Id: Iea0de1640d4e5b21ecc7e9c1dd6d36f214d647c2
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: http://openocd.zylin.com/6025
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The macro AC_HEADER_TIME has been obsoleted by autoconf 2.70.
Not all systems provide 'sys/time.h', plus some old system didn't
allowed to include both 'time.h' and 'sys/time.h' because 'time.h'
was included by 'sys/time.h' and was not properly protected to
allow multiple inclusion.
The macro AC_HEADER_TIME helps to detect such odd case.
Nowadays all the systems properly protect 'time.h', so its safe to
unconditionally include 'time.h', even if it is also included by
'sys/time.h'.
The case of systems without 'sys/time.h' is already covered by
configure.ac through the directive
AC_CHECK_HEADERS([sys/time.h])
Remove the obsoleted autoconf macro and simplify the code by
including 'time.h' unconditionally and check HAVE_SYS_TIME_H to
include 'sys/time.h'.
Change-Id: Iddb3f3f1d90c22668b97f8e756e1b4f733367a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6010
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The macro AC_PROG_CC_C99 has been obsoleted by autoconf 2.70 and
triggers a set of warnings from both 'aclocal' and 'autoconf'.
The test of AC_PROG_CC_C99 is now included in AC_PROG_CC.
For autoconf 2.69 and earlier the macro is still required, so
cannot be simply dropped.
Use a conditional test to avoid the warning on autoconf 2.70 but
still use AC_PROG_CC_C99 on older autoconf.
Change-Id: I5e8437f5a826fb63be6d07bcb5bb824f94683020
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6009
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
When using the adapter olimex arm-jtag-swd (to convert to SWD a
JTAG-only FTDI adapter), the pin trst on JTAG side is re-used to
control the direction of pin SWDIO on SWD side.
There is a single reset API at adapter driver to assert/deassert
either srst and/or trst. A request to assert/deassert srst can
cause also trst to change value, hanging the SWD communication.
In SWD mode, ignore the value passed to trst.
Change-Id: I5fe1eed851177d405d77ae6079da9642dc1a08f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6006
Tested-by: jenkins
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit ab90b87778 ("configure: remove AM_MAINTAINER_MODE,
effectively always enabling all the rules") removes the configure
flag '--enable-maintainer-mode' and its documentation, but have
left a reference to the removed subsection 'primermaintainermode'
and this triggers a warning in doxygen:
doc/manual/primer/autotools.txt:21: warning: unable to
resolve reference to 'primermaintainermode' for \ref
command
Remove the obsoleted paragraph.
Change-Id: I56e69ef033d546d159745bed1b47c6105827e7ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ab90b87778 ("configure: remove AM_MAINTAINER_MODE, effectively always enabling all the rules")
Reviewed-on: http://openocd.zylin.com/6003
Tested-by: jenkins
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
When build using libjaylink as git submodule, doxygen includes the
libjaylink files and complains for multiple 'mainpage' comment
block, one in OpenOCD and the other in libjaylink:
src/jtag/drivers/libjaylink/libjaylink/core.c:37: warning:
found more than one \mainpage comment block! (first
occurrence: doc/manual/main.txt, line 1), Skipping current
block!
Exclude libjaylink submodule from doxygen.
Change-Id: I5e856817344c9f21f8c26f077a23c00b83cfbcb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6000
Tested-by: jenkins
The section name 'primerjtag' is used twice, causing doxygen to
complain:
warning: multiple use of section label 'primerjtag',
(first occurrence: doc/manual/primer/jtag.txt, line 107)
Rename one of them.
Change-Id: Id307915dbc51a7f647fab4fb28ab431e65344d61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5999
Tested-by: jenkins
When doxygen is built out-of-tree, it fails to find the generated
file startup_tcl.inc:
src/openocd.c:59: warning: include file startup_tcl.inc
not found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Add '@builddir@/src' to INCLUDE_PATH.
Change-Id: I51f2f6fe7224bba0f8b3db7219f9831de4e67139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5998
Tested-by: jenkins
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
Doxygen complains about non-closed nested comments:
doc/manual/style.txt:423: warning: Reached end of file
while still inside a (nested) comment. Nesting level 1
(probable line reference: 149)
This is caused by the string '/**' that is interpreted as the
beginning of a comment.
Escape the string to not let doxygen consider it as a comment
While there, replace @code/@endcode with @verbatim/@endverbatim to
properly render the line.
Change-Id: If2a27c4cf659326e317cc4ac8c0b313e97e40432
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5996
Tested-by: jenkins
Commit 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.") was
initially proposed as http://openocd.zylin.com/3429/ then replaced
by http://openocd.zylin.com/3980/
The initial proposal was for file '99-openocd.rules', in which
MODE="664" was the norm.
After merge of http://openocd.zylin.com/2804/ the new udev rules
in '60-openocd.rules' switched to MODE="660", but the evolution of
the above patch missed this change.
Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform
them to the rest of the file.
Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.")
Reviewed-on: http://openocd.zylin.com/6004
Tested-by: jenkins
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
To prevent executing the Jim Tcl tests, the makefile's target
'check-recursive' has been overridden in commit 56d163ce79
("jimtcl: update to 0.77, the current version, enable only
specific modules").
This causes a runtime warning during build:
Makefile:6332: warning: overriding recipe for target 'check-recursive'
Makefile:5098: warning: ignoring old recipe for target 'check-recursive'
Instead of override the makefile's target 'check-recursive',
prevent the recursion by re-assigning as empty the variable
SUBDIRS for this specific target only.
Change-Id: I03d1c467eba42316a59aeed4612d6bdbe6211282
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 56d163ce79 ("jimtcl: update to 0.77, the current version, enable only specific modules")
Reviewed-on: http://openocd.zylin.com/5986
Tested-by: jenkins
Driver 'openjtag' requires both libftdi and libusb1.
The current check is incorrect and the driver is built when
libftdi is present with libusb0 and without libusb1, which causes
the linker to fail resolving the required libusb1 symbols.
Remove the check for libusb0 on driver 'openjtag'.
Create a new adapters group LIBFTDI_USB1_ADAPTERS to hold the
driver 'openjtag'.
Change-Id: I1f5e554b519e51c829d116ede894639cb55a26aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5989
Tested-by: jenkins
At gdb attach, the event TARGET_EVENT_GDB_ATTACH is in charge of
halting the target.
For HW thread, rtos_update_threads() should be called after the
event to detect and record the new 'halted' status. Instead it is
called immediately before the event, thus reading the status
before the halt.
Move after the event the call to rtos_update_threads().
Change-Id: Iab3480ea0f5283ed6580f0f6c11200083197d1e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5983
Tested-by: jenkins
The targets armv7a in file cortex_a.c inherit the register list
from file armv4_5.c thus, depending on the core status, some
register get marked as not existing.
For HW threads other than current target, the registers in the
list are not checked for existence and are all forwarded to GDB
that in turns complains for too many data:
Remote 'g' packet reply is too long (expected 68 bytes, got 104 bytes)
Check all the attributes of the registers and pass to GDB only the
valid registers.
To test it, use a SMP cortex-a target (2 cores are enough) and add
-rtos hwthread
to all the cores. Connect GDB to OpenOCD and issue the GDB command
info threads
Change-Id: Ie66119fe83a3c8d53e9d18dda39e60fd97769669
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5981
Tested-by: jenkins
The target code for assert reset on cortex_a has been patched on
commit b0698501b0 ("cortex_a: fix cortex_a_assert_reset() if
srst_gates_jtag") then in cdba6ba0ad ("cortex_a: fix reset for
SWD transport") to workaround the mismatch between jtag and swd
implementations. See discussion for the second patch at
http://openocd.zylin.com/3641/
While all of these mismatches should hopefully be cleaned by the
reset framework rework, an extension of the workaround of the
second patch is required for dapdirect transports, either
dapdirect_swd and dapdirect_jtag.
Extend the existing workaround to all non-jtag transports.
Change-Id: Ia6a9d43bab524cbb3de4c37ce24c45f25187353d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5979
Tested-by: jenkins
If OpenOCD is reading trace data from the target, at exit it
should stop the adapter to gather data, but should left the target
still producing them.
Add a helper in armv7m_trace to disable the adapter's trace and
call it during OpenOCD teardown.
This also provides a workaround for an issue in the firmware of
ST-Link V3 till version V3J7. If the SWD connection is closed when
trace is active, at following connection the trace does not work
anymore.
Change-Id: I47ccab61405384938555096c5aca789eaa090d27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5978
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Automake issues a warning
Makefile.am:46: warning: wildcard $(srcdir: non-POSIX variable name
Makefile.am:46: (probably a GNU make extension)
because the GNU make function 'wildcard' is not POSIX.
Also the GNU make function 'shell' triggers a similar warning.
Use the POSIX extension '!=', that executes an arbitrary shell
command, to replace the GNU make 'wildcard'.
Don't include the file 'NEWS' because automake already includes it
by default.
Change-Id: Ice560c3789cec4f3f2197a255d6f5af7b1fde634
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5965
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
The warning message regarding wrong verification checksum for LPC2000, claims that the verification will fail, but the checksum written correctly by openocd. Clarify this in the warning message.
Change-Id: I929ac767f7f9fdad9bace250c8c04a776462800a
Signed-off-by: Luca Lindhorst <l.lindhorst@wut.de>
Reviewed-on: http://openocd.zylin.com/5956
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The git preliminarily version of clang 12.0.0_r370171
f067bc3c0ad6 reports an error in the expansion of the macro
SMI_READ_REG():
error: '(' and '{' tokens introducing statement expression
appear in different macro expansion contexts
[-Werror,-Wcompound-token-split-by-macro]
Remove one intermediate macro expansion to make clang happy.
Change-Id: I8ae6d9c18808467ba8044d70cbf0a4f76a18d3e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5958
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This should provide greater compatibility with different OpenULINK
targets which might be using various endpoints numbers. Since they're
advertised in the USB descriptor anyway it makes sense to autodetect
them.
Interface is no longer claimed before attempting to load firmware to a
freshly booted device, so I have no idea if this will break on windows
or other uncommon systems (Paul).
Change-Id: Iee10dcb6911dcf46239c430e174d9f98b5bde3c2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2445
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The 'historically' main repository of jimtcl in repo.or.cz has
lost sync with the github current main repository since July 2020.
The new tag 0.80 is not present in repo.or.cz.
The developer of jimtcl has been in contact with the admins of
repo.or.cz to fix the not better described sync issues and has now
decided to stop any further tentative. A new README has been added
on 2020-11-19 in the old repository to inform that it is abandoned
in favour of github. The old content in repo.or.cz will remain due
to forks that still exists in the same server.
Switch OpenOCD git submodules to fetch jimtcl code from the main
development repository in github.
Change-Id: Ia2d59f1347ccfe374538b38131badfd46054eb91
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5948
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The use of 'void *' makes the pointer arithmetic incompatible with
standard C, even if this is allowed by GCC extensions.
The use of 'void *' can also hide incorrect pointer assignments.
Switch to 'uint8_t *' and add GCC warning flag to track any use of
pointer arithmetic extension.
Change-Id: Ic4d15a232834cd6b374330f70e2473a359b1607f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5937
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit 80f1a92bd7 ("mips64: Add generic mips64 target support")
adds a log of the target's program counter in function
mips_mips64_debug_entry() by directly casting the little-endian
buffer in pc->value.
This is going to print an incorrect value on big-endian hosts.
Use the function buf_get_u64() to return the register value.
Not tested on real HW. Issue identified with GCC compiler flag
'-Wcast-align=strict' after change http://openocd.zylin.com/5937/
("target/register: use an array of uint8_t for register's value").
Change-Id: Icbda2b54a03fdec287c804e623f5db4252f9cd2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 80f1a92bd7 ("mips64: Add generic mips64 target support")
Reviewed-on: http://openocd.zylin.com/5944
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The original code passes to ->read_core_regs() and to
->read_xpsr() the pointer to the little-endian buffer reg.value.
This is incorrect because the two functions above require a
pointer to uint32_t, since they already run the conversion with
arm_le_to_h_u32() in the jtag callback.
This causes a mismatch on big-endian host and the registers get
read with the incorrect endianness.
Use an intermediate buffer to read the registers as uint32_t and
to track the destination reg.value pointer, then copy the value in
reg.value after the call to jtag_execute_queue().
Tested with qemu-armeb and an OpenOCD built through buildroot
configured for cortex-a7 big-endian.
Note that if jtag_execute_queue() fails, the openocd register
cache is not updated, so the already modified flags 'valid' and
'dirty' are incorrect. This part should be moved after the call to
jtag_execute_queue() too.
Change-Id: Iba70d964ffbb74bf0860bfd9d299f218e3bc65bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5943
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit fc2abe63fd ("armv7m: use generic arm::core_mode") adds
two special modes for ARMv6M and ARMv7M in struct arm_mode_data[].
While these modes do not have any additional register to be dumped
by command 'arm reg', the command still prints an header for these
modes but not followed by any register.
Detect the special modes for ARMv6M and ARMv7M and skip them to
avoid printing the useless header.
Change-Id: I04145769e5742624f143c910eebf9a6f6d8e3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fc2abe63fd ("armv7m: use generic arm::core_mode")
Reviewed-on: http://openocd.zylin.com/5942
Tested-by: jenkins
Commit fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor
mode") introduces the secure mode 28 of ARMv6 as a synonymous of
mode 22 (MON), but does not add it in the switch/case in command
'arm reg'.
When command 'arm reg' scans the array arm_mode_data[] on targets
without secure modes, it does not detect the new secure mode as
not supported by the architecture, thus triggers a segmentation
fault when it try to read the register's value from unallocated
memory.
Issue detected with target arm926ejs.
Add the new mode in the switch/case and treat it as the mode MON.
Change-Id: I2b72cc558e097879a7ee6ea601200bfda6b60270
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor mode")
Reviewed-on: http://openocd.zylin.com/5941
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reading of DPIDR is the very first operation after JTAG to SWD sequence.
Without this change if DPIDR read fails then swd connect fails.
Keep trying JTAG to SWD sequence and DPIDR read until success
or timeout 0.5 sec. It makes setting of adapter srst delay on SWD transport
mostly unnecessary.
Also test for ERROR_WAIT (which should not occur according to
IHI 0031E B4.3.2 but a quirk is known) and if bus is kept stalled
then issue abort to make the next connect possible.
Change-Id: Id8fe6618605bbeb4fed5061e987ed55de90a35f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If dap_dp_read_atomic() in 30 trials loop fails, dap->do_reconnect is set.
Following dap_dp_read_atomic() calls dap_queue_dp_read() which in case
of SWD transport calls swd_queue_dp_read(). It starts
with swd_check_reconnect() and it calls swd_connect() because
dap->do_reconnect is set. swd_connect() does some initialization,
reads DPIDR and calls dap_dp_init() again!
Moreover if dap_dp_init() is called from cortex_m_reset_(de)assert()
one level of recursion is necessary to reconnect the target.
Introduce dap_dp_init_or_reconnect() for use in cortex_m reset
and similar.
Remove loop of 30 atomic reads of DP_STAT to prevent unwanted recursion.
Change-Id: I54052fdefe50bf5f7c7b59fe751fe2063d5710c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5729
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Every debug log of OpenOCD contains approximately 130 lines like:
Debug: 264 147 command.c:354 register_command_handler(): registering 'flash'...
Because only root name of the command is logged, most of lines is not
too informative. E.g. registering 'flash' is repeated 14 times.
Karl Passon submitted the patch [1] changing the logged cmd name from
root to lowest level. It makes the log better. Unfortunately we also have
'reset_config' and 'cortex_m reset_config' and similar which looks
equal in the log after [1].
Moreover [1] has not been reviewed for 5 years.
So my guess is that nobody uses that crap in debug log.
Save more than 10 kbytes in any debug log and make log analyse easier
by blocking log command in #if 0 block.
If some developer eventually needs to debug cmd registering he can easily
enable logging again.
[1] http://openocd.zylin.com/2765
Change-Id: Ib7e528aadd692fd0da2e3c005b4c5a484551b728
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid multiple definition of cmsis_dap_usb_backend and
cmsis_dap_hid_backend using 'extern'.
Move the prototypes in cmsis_dap.h.
Remove the useless #if/#endif around the prototypes.
Change-Id: I8d73fe148e2155620244bc887d4235e9af530e30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5790
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
http://openocd.zylin.com/4831 has following problems in selecting
USB device/interface to connect:
- attempts connection to any device with user class and 2 bulk endpoints
- regardless of cmsis_dap_vid_pid or cmsis_dap_serial setting
connects to the first suitable device
Distinguish between real match and no filtering cases and use that info
appropriately.
Add debug messages to show why the interface is refused.
Move CMSIS-DAP interface string detection before checking of class/endpoints
to give more understandable debug log in the case the device is refused.
Keep track of reliable matches in both device and interface enumeration.
First search for the interface with CMSIS-DAP in the interface string.
If it fails, chose the first suitable interface.
Change-Id: Ia1aacd5631a9f5c5db580bfb5745ceb6240d61ad
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5789
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This change implements CMSIS-DAP v2 which works with raw USB bulk transfers.
The old driver is now split into a generic CMSIS part and a HID backend,
with a new raw USB backend for CMSIS-DAP v2.
New commands:
- cmsis_dap_backend (usb_bulk | hid | auto)
- cmsis_dap_usb interface <interface number>
Change-Id: I4218477b12ccbfe19c9b332321cd21394bf44e30
Signed-off-by: Mickaël Thomas <mickael9@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4831
Tested-by: jenkins
PSoC6 erases flash to 0x00 not more common 0xff, so a device
with erased flash loads xPSR.T=0 from the zeroed reset vector.
Wrong thumb bit value caused a target algorithm failed with HardFault.
The low level write to xPSR solved the problem only if xPSR cached
copy was not marked dirty.
Later commit 49bd64347a fixed T setting
for all Cortex-M target algorithms.
Since 49bd64 this part of code is useless as xPSR target_start_algorithm()
sets always xPSR dirty so the effect of the low level write is eliminated
(and proper setting of thumb bit is ensured in target_start_algorithm())
Change-Id: I68aea5e921fbc6203f2fe91a45f10d22869327de
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5875
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M (not M0, M0+) target was stopped in the middle of
a conditional IT block or in the load/store multiple instruction,
cortex_m_debug_entry() used wrong xPSR bits to detect it and then
cleared 8 bits of the exception number from xPSR
- probably wrong bit mask again.
I believe clearing of the ICI/IT bits in cortex_m_debug_entry() has no
reason as Cortex-M does not use instruction injecting.
Remove the wrong code.
The change was originally a part of http://openocd.zylin.com/4862
It is now re-submitted as #4862 is not ready.
Change-Id: If91cd91d1b81b2684f7d5f10cf20452cde1a7f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5874
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Old stlink firmware in stlink V1 and stlink V2 pre-J15 do not
handle FPU registers in the read_reg() and write_reg() API.
Add code to be compatible with the new API of OpenOCD.
Change-Id: Ib0439c5294b6911ea75efe8c7fa085b014317a4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5883
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The API of hla have been defined from ST-Link basic operations.
By chance, all the current implementation of hla (st-link, ti-icdi
and nulink) share the same way to handle the parameter 'num' of
the API read_reg() and write_reg(), that is simply using it to
initialize the field REGSEL (bits [6:0]) of armv7m Debug Core
Register Selector Register (DCRSR).
Add a comment in the API definition to highlight this, in case it
get used by a further hla implementation, then rename as 'regsel'
the 'num' parameter.
Change-Id: I4b6a2c7d78b4fc4de2b9b2bdba065414b15c6ba3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5882
Reviewed-by: Edward Fewell <edwardfewell@hotmail.com>
Tested-by: jenkins
Reviewed-by: Zale Yu
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Consolidate low level register read/write.
Floating point registers were handled by target_read/write_u32
unlike other registers handled by cortexm_dap_read/write_coreregister_u32
There is no reason to do so in cortex_m.
Remove cortexm_dap_read/write_coreregister_u32
and use cortex_m_load/store_core_reg_u32 directly.
Similarly HLA adapters register read/write interface supports all registers
so use it for any floating point and other registers.
Change-Id: Ida679e5f4fec02d94ffb0bd3f265ed7ed2221cdc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5864
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Make arm register id coherent with reg_list index.
Without this reg_list[ARMV7M_R12] was possible but
reg_list[ARMV7M_FPSCR] was out of bounds.
Remove unused items from reg_list index.
Change-Id: I84d3b5c496fc1839d07a5b74cb1fd1c3d4ff8989
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5862
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Introduce a 'hidden' flag in struct reg to support a register cache
containing different views of same data: e.g. Cortex-M has
primask, basepri, faultmask and control registers accessed
as one word. With the hidden flag we can add an reg_list item
corresponding to hw access without exposing the register to user level.
All the struct reg are allocated with calloc() but one in xscale.c
allocated by malloc(). Change this one to use calloc() as well
to guarantee initial value hidden=false
Change-Id: I8da9f5a5a60777ae7ef943a841307487bd80fc6f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5325
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Use the board file name as <company>_<name>.cfg
Add the SPDX tag to workaround an error in checkpatch that fails
to recognize as valid a patch that only changes a file name.
Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5931
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
When the core is in sleep mode, the core is no longer retiring
instructions. Cortext M remains in "unknown" state. This patch converts
sleep mode to "running" state.
Change-Id: I1e9b6c9be51fd0f1f6ce81af9b1f5f9f1f43c661
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5921
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
Use integer rounding for the computation of prescaler.
Improve the test of prescaler range, knowing its value would be
decremented before being written in TPIU ACPR.
Change-Id: I041dde1dca41323904e36a6b6975028a6de902b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5909
Tested-by: jenkins
The value stored in TPIU ACPR is the prescaler value decremented
by one. Thus, the test should verify that prescaler does not
exceed the maximum ACPR value plus one. Also, zero value is not
allowed for prescaler.
Change-Id: I1817f04f2a310b2f413bad726f0cb9dd6a4172e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5907
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Commit 462c012066 ("Add complete JTAG debug logging.") breaks
the build for minidriver, that is enabled either on zy1000 build
and on minidriver-dummy build. The check on BUILD_ZY1000 was added
to pass the auto-build in jenkins. While the build issue with
minidriver-dummy was known, as reported in the comment, it was not
addressed and got ignored for slightly more than one year.
Use the macro HAVE_JTAG_MINIDRIVER_H in place of BUILD_ZY1000 to
take in account both builds that require the minidriver.
Fix also the build in case configure enables the HLA drivers due
to autodetection of libusb. The HLA drivers would not be in the
build and the function transport_is_hla() would be missing.
Change-Id: I1d85c5fa247bf4a85aba29b233c0b573b46665bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5911
Tested-by: jenkins
The function arm7tdmi_clock_out() has one unused 'deprecated'
parameter.
Drop the unused 'deprecated' parameter and the FIXME above it.
Change-Id: Ia8de41f5b8258825faccc737bba622e44c81a7ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5912
Tested-by: jenkins
The only code dealing with tftp in OpenOCD was in eCos build, code
already dropped in commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") almost 8 years ago.
Drop tftp related documentation too.
Change-Id: I0defc8f844e74c90894dca04a652dcc497a520e1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5913
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Jimtcl 0.80 (2020-10-29) adds dependency to libutil, which is part
of the GNU libc.
The library is searched and used by jimtcl build, but still has to
be linked in by OpenOCD as indirect dependency.
While OpenOCD is still using jimtcl 0.79, let's prepare to switch
to the next version.
Add libutil search in configure.ac.
Change-Id: I5a8952161b0e5b93fc00d23be256b5274d31e08c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5922
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
regsub doesn't work correctly on macOS Catalina, which results in
an incorrect CHIPNAME derived from the current target. Since regsub
is only used by this target, replace it with a simple string search
for '.' followed by a substring. This is funcionally equivalent to
what the regular expression was doing, but instead relies in simpler
string operations that should have little to no differences
between systems.
Also, refactor CHIPNAME detection into proc stm32h7x_chipname, so
it's always retrieved in the same way without duplicating the code.
Change-Id: Ia9f63f56b508688e74278b022eaec47e503916e7
Signed-off-by: Alberto Garcia Hierro <alberto@garciahierro.com>
Reviewed-on: http://openocd.zylin.com/5872
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When a target examination fails, continue to examine subsequent targets.
Return the number of targets that failed to examine.
Change-Id: I883a0c445edc7eb00f496b79271d773771ec6b66
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
returning the created service seems useful:
as the only method to get the freshly created service is by getting the
last item in the services linked list, and this seems to be like an
intrusion to service internal mechanism.
possibly, we could get the service from a connection but this is possible
only from [new_connection|input|connection_closed]_handler_t, but this is
not always practical:
example: armv7m: add a TCP channel to stream captured trace
http://openocd.zylin.com/#/c/5345/
here we poll for trace and broadcast to all connections
outside of these xxx_handler_t functions
also, storing one of the connections in new_connection_handler_t and get
the service from it is possible, but this will make the code less readable.
Change-Id: I5fef1baecec1e054953c6faf5b99d864ecc97f02
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5717
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The function setup_command_handler() was used in the eCos build of
OpenOCD, thus it was exported and a comment was added to remark it
should remain not-static. Unfortunately the comment was missing
the relevant information of the special build that requires so.
Also unusual is that there is no include file that declares the
prototype of the function.
The comment above the function was added in two steps, in commit
ea3e49f4e2 ("fix embedded builds") and commit fb96b8607a
("openocd: setup_command_handler() must not be static"), again
without info about the special build.
Also the mailing list archive does not report any further detail.
The only hint is in the first commit above that also adds a test
on BUILD_ECOSBOARD in a #if.
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code")
removes all the eCos code, that effectively includes the both the
prototype and the call to the function setup_command_handler(),
http://openocd.zylin.com/#/c/503/2/src/ecosboard.c@a1092
but did not reverted the function to static.
With all the 'external' uses of this function being dropped, set
the function setup_command_handler() to static and remove the
obsoleted and misleading comment.
Change-Id: I4d6b83dec2a838119821189fc67949bfca070035
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function rtos_try_next() is only used internally.
Make it private.
Change-Id: I68c6b8d8e6bbf3d674b0e0199e63bc02d358c04e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5899
Tested-by: jenkins
The only use of this function has been removed with commit
159f11fefc ("jtag: set default "jtag_only" to uninitialized
transports").
Get rid of the unused function.
Change-Id: I79dd1d55bd54ed8edc39ed3443e6c3c01794f063
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5898
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions that are not used outside the file should be declared as
static.
Change-Id: I57b2fa6e49e87e14604bd34c4f1d2f037f401507
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5897
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I58c9f5557d4809db9ccc34d32182c3797f825da1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5896
Tested-by: jenkins
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9f97571a528f0cb3c3c26f873577ab16fdec3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9731a35496cd1c7421563c8961da5fa0e3cc71c3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5894
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I52d46ed6d4c9b98a7152eb23274c836416f409a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The new libftdi 1.5 (2020-07-07) changes some API, deprecating the
old ones. This cause a warning at compile time.
Detect in configure the version of libftdi.
Use the new API in the driver's code.
Add an helper include file 'libftdi_helper.h' that wraps the old
API for backward compatibility with old libftdi.
Change-Id: I7800fbebe17dd0ce62e55b3598d8c08be8875bb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/286/
Reviewed-on: http://openocd.zylin.com/5891
Tested-by: jenkins
Automake will search for the helper scripts in the folder that
contains the current Makefile.am (typically '.'), then some of the
scripts will be also searched in '..' and '../..'.
If the parent folders '..' or '../..' of OpenOCD source code
contain a file named 'install.sh', then automake will use it and
will assume that the same folder should contains also 'ltmain.sh'.
This situation can either cause the build to fail or automake to
use incorrect helper scripts.
Force automake to only search for helper scripts in the current
directory.
Change-Id: I00bbd6bf9057c94cf5007e5ecda3fefd683481f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/285/
Reviewed-on: http://openocd.zylin.com/5890
Tested-by: jenkins
Is it possible to run OpenOCD without any target, for example to
only dump the rom-tables of an arm dap, or to perform low level
jtag operations.
But without any target created, the command 'target current'
causes OpenOCD to abruptly exit.
Handle in command 'target current' the case of no targets.
Change-Id: Ide15cb13bec84b88ccc3e7126523c04a6d70e636
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5881
Tested-by: jenkins
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
This is somehow an extension of existing adiv5_jim_configure(),
but includes the 'address' in the mem_ap.
Rewrite adiv5_jim_configure() using the new helper.
Change-Id: Ia7effeeece044004d459b45126ed4961a98b8568
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5857
Tested-by: jenkins
in RM0399 rev2, there was these bits in DBGMCU_CR registers:
- DBGSTBY_D3 : bit 7
- DBGSTOP_D3 : bit 8
these bits have been changed to reserved in rev3
Change-Id: I9d10d90e383795dc8e25a117d59fa065dc594610
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5861
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang static analyzer reported:
Warning: line 196, column 3
Potential leak of memory pointed to by 'fields'
Free allocated memory pointed by 'fields' and fields[i].in_value
Change-Id: I0b3935d9a235544afc03e39a4648319047e65815
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5906
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Warning: line 373, column 15
Assigned value is garbage or undefined
Most probably a false warning, building the hex string byte
per byte seems too complicated for static analyze.
Change malloc to calloc to silence the warning.
Change-Id: I746d43fa51abf05582ccf2680ed72dc557798a7a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5905
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Warning: line 955, column 3
Argument to free() is the address of a global variable, which
is not memory allocated by malloc()
It is definitely a false alarm. Simplify concatenation of arguments
and allocate a string always to silence the warning.
Change-Id: I5ac4cc610fc35224df0b16ef4f7102700363249f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5904
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In commit a1ce28b118 ("rename some target scripts to be
consistent with the rest") the following renames was applied, but
the old names are still referenced:
tcl/target/{sam7se512.cfg => at91sam7se512.cfg}
tcl/target/{sam7x256.cfg => at91sam7x256.cfg}
Fix the board files to use to correct target config filename.
Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
When OpenOCD is installed to the host the 'tcl' folder gets
usually installed in /usr/share/openocd/, thus having 'tcl' as
prefix of the target's file causes 'find' to fail.
Remove the 'tcl' folder prefix.
Change-Id: I3dc484c8de6af8f5aae4dd1b230522ee47ae2ba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This is a) broken and b) doesn't include anything other than the
(broken) target alias. Don't see any reason for it to exist.
Change-Id: I833635eeac392bf7c0c39f51ff2f76525ba2d406
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/5884
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The config_trace function has an out-parameter for generating the
prescaler for the TPIU. The STLink implementation wasn't always writing
it, causing the tpiu command to load uninitialized stack memory (minus
one) into the TPIU's prescaler register when 'external' was requested.
This change ensures that the out-parameter (and the other one,
trace_freq, which hadn't caused any buggy behavior for me) are written
every time.
Signed-off-by: Cliff L. Biffle <cliff@oxide.computer>
Change-Id: I222975869b1aa49cc6b1963c79d5ea0f46522b8c
Reviewed-on: http://openocd.zylin.com/5656
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Now that it’s possible to start profiling from either a running or a
halted state, rather than unconditionally halting after profiling
finishes, it makes more sense to restore the processor to whatever state
(running or halted) it was in before profiling started.
Change-Id: If6f6e70a1a365c1ce3b348a306c435c220b8bf12
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5237
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are a handful of implementations of profiling. There is the
default implementation, which repeatedly halts and resumes the target,
sampling PC each time. There is the Cortex-M implementation, which
uses PCSR if available, otherwise falling back to halting and resuming
and sampling PC. There is the OR1K implementation, which reads NPC
repeatedly. Finally, there is the NDS32 implementation which uses some
kind of AICE commands with which I am unfamiliar.
None of these (with the possible exception of the NDS32
implementation) actually require the target to be halted when starting
profiling. The Cortex-M and OR1K actually resume the target as pretty
much their first action. The default implementation doesn’t do this,
but is written in such a way that the target just flips back and forth
between halted and running, and the code will do the right thing from
either initial state. The NDS32 implementation I don’t know about.
As such, for everything except NDS32, it is not really necessary that
the target be halted to start profiling. For the non-PCSR Cortex-M and
default implementations, there is no real harm in such a requirement,
because profiling is intrusive anyway, but there is no benefit. For
the PCSR-based Cortex-M and the OR1K, requiring that the target is
halted is annoying because it makes profiling more intrusive.
Remove the must-be-halted check from the target_profiling function.
Add it to the NDS32 implementation because I am not sure if that will
break when invoked with a running target. Do not add it to any of the
other implementations because they don’t need it.
Change-Id: I479dce999a80eccccfd3be4fa192c904f0a45709
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5235
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
HWID is a part of 32 bit CONFIGID register. hwid member of struct nrf5_info
was typed uint32_t to enable direct CONFIGID read and masked afterwards.
Change to uint16_t to unify with hwid in struct nrf5_device_spec
and RM description.
Change-Id: Ib720d3ce23c301aee41d074ea78a6f00a23aed68
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5589
Tested-by: jenkins
nRF52 devices indicate a flash error by emitting hard fault
exception (unlike nRF51 series).
Change error message when NVMC READY read fails. A hard fault
from flash erase/write operation is detected here.
Check exit point of the flash write algo to ensure a failed
write is recognised.
Change-Id: I637eda268a6bf45f7f41bcb9dcd82db8f5cb41b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5587
Tested-by: jenkins
nRF51 devices have a clumsy flash protection based on UICR CLENR0.
A code running in RAM can write to a protected flash region without
any hint the protection gets violated.
NVMC flash page erase obeys protection setting but fails absolutely
silently.
Before this change the first problem was not addressed in the code.
To justify the second one, protection was loaded during probe,
after protection setting and after a mass erase.
Move protection updates to the beginning of erase/write operation
and limit them to nRF51 series only. Check for protected sectors
before write.
The change also fixes the problem of 'nrf5 mass_erase' on
nRF52833/840 devices. They use ACL flash protection, which is not
supported in nrf5 driver. mass_erase then looked like it failed.
Change-Id: Ie58cda68eb104d410b02777c3df5b343408e2666
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5522
Tested-by: jenkins
Protection setting has not ever worked. UICR CLENR0 register cannot
be simply written but has to programmed because it resides in UICR
page of the flash.
Enable flash programming before writing CLENR0 and set back to r/o
afterwards.
Inform the user that reset might be required.
Change-Id: Ib0f96c74ba3583ac33f4394ddb57d8c8895adf53
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5586
Tested-by: jenkins
Handle Ctrl+K shortcut which clears the line from the cursor position
to the end of line.
Change-Id: I2ecff5284473cef7c11cf9cb7e1c0c97d55f6c1c
Signed-off-by: Brian Brooks <brooks.brian@gmail.com>
Reviewed-on: http://openocd.zylin.com/5868
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
With help of actionpoint mechanism now it is possible to introduce
watchpoints support for ARC.
Change-Id: I5887335d0ba38c15c377bc1d24a1ef36e138cf65
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5867
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added comment to ti-icdi.cfg specifying how to get serial and an example of
specifying hla_serial for ti-icdi devices. This has been implemented in revision
2121a8f92969804611412b705af8114697a647dc
Change-Id: I648458a4dea176beae6a3f1a4e5641d0206077eb
Signed-off-by: John Pham <jhnphm@gmail.com>
Reviewed-on: http://openocd.zylin.com/2528
Tested-by: jenkins
Reviewed-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Used jtag_libusb_open from libusb_helper.h instead of
libusb_open_device_with_vid_pid to get device handle,
as well as managing context, i.e. similar to stlink_usb.
Direct calls to libusb1 are left in for the moment.
(When this Gerrit revision was originally created,
the jtag_libusb_ wrappers did not return error conditions.)
Tested w/ a TM4C123GXL board
Change-Id: I71e9a366356c125444d4813e58ddd9b6c6498bf0
Signed-off-by: John Pham <jhnphm@gmail.com>
Signed-off-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-on: http://openocd.zylin.com/2527
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The commit b68674a1da ("Upstream tons of RISC-V changes.") was
proposed well before commit 3ac010bb9f ("Fix debug prints when
loading to flash"), but the merge got in different order.
After latest merge, the master branch fails to compile.
Fix the compile error.
Change-Id: Ia3bd21d970d589343a3b9b2d58c89e0c49f30015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5856
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Add support for ATSAMG55x19 Rev.B.
Both chips have nearly the same cidr, however, Rev.B has an incremented version.
Change-Id: I5939c41fa5d54c4d3bfb850964974b878f709d13
Signed-off-by: Benedikt-Alexander Mokroß <mokross@gessler.de>
Reviewed-on: http://openocd.zylin.com/5825
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function adiv5_jim_configure() casts the void pointer
'target->private_config' to a struct adiv5_private_config pointer.
This is tricky in case of aarch64, where the private data are in a
struct aarch64_private_config that has as first element the struct
adiv5_private_config.
While the current solution is working fine, it's not clean and
requires special attention for any further code development.
Override 'target->private_config' to the correct pointer while
calling adiv5_jim_configure().
Change-Id: Ic2fc047dd1e57013943d96e6d5879a919d1eb7b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5847
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change aarch64 to use ap-num setting if provided. Fall back to original
behavior of using first AP when ap-num is invalid.
Change-Id: I0d3624f75c86ba5fd5a322ac60856dbbb6e71eaf
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5831
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The prescaler computation should round at the nearest integer
value, not to the next integer value.
Change-Id: I957e0774421211f3c4ba4b312738b1c67b87c4a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 051e80812b ("drivers/jlink: fix calculate_swo_prescaler formula")
Reviewed-on: http://openocd.zylin.com/5846
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Search in XDG_CONFIG_HOME as per XDG Base Directory Specification
in addition to $HOME/.openocd.
On Darwin, search in ~/Library/Preferences/org.openocd/ which
appears to be one of the conventional locations.
Make $OPENOCD_SCRIPTS highest priority on all platforms, previously
it was only higher on WIN32.
Update the documentation to reflect the search order.
Change-Id: Ibaf4b59b51fdf452712d91b47ea2b5312bb5ada9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3890
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Log lines already print a new line, so these superfluous \r\n result in
blank lines being printed in the log. Remove per review comment
request.
Change-Id: I8f5b20776634cf70ce4490fc4f732c916130928a
Signed-off-by: Karl Palsson <karlp@etactica.com>
Reviewed-on: http://openocd.zylin.com/5843
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Remember, don't cast your pointers between types of different sizes!
While the FreeRTOS handlers attempt to account for different pointer and
list widths, the types used are always fixed, so this will _remain_
broken if/when someone targets FreeRTOS on 8/16/64 bit targets. (Note
that this patch does not _change_ that, it was fixed to 32bit before as
well)
In the meantime, this properly handles 32bit reads on a mips BE system
(ath79) as well as remaining fully functional on x86_64.
Change-Id: I677bb7130e25dccb7c1bee8fabaee27371494d00
Signed-off-by: Karl Palsson <karlp@etactica.com>
Reviewed-on: http://openocd.zylin.com/5842
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a target is not examined, command vector_catch crashes while accessing
the debug_ap NULL pointer.
maskisr and reset_config commands don't require this check.
Change-Id: I949b6f6e8b983327dd98fbe403735141f8f0b5d6
Signed-off-by: Daniel Trnka <daniel.trnka@gmail.com>
Reviewed-on: http://openocd.zylin.com/5813
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
a) TPIU_ACPR is defined as:
SWO_baudrate = TRACECLKIN/(TPIU_ACPR +1)
b) TPIU_ACPR is set by armv7m_trace_tpiu_config()
target_write_u32(target, TPIU_ACPR, Prescaler-1), so
TPIU_ACPR = Prescaler-1
Replacing TPIU_ACPR in a), we get:
SWO_baudrate = TRACECLKIN/Prescaler, so
c) Prescaler = TRACECLKIN/SWO_baudrate
The Prescaler calculated by calculate_swo_prescaler() is greater by 1:
Prescaler = TRACECLKIN/SWO_baudrate + 1
The second problem is that even in situations when
an exact baudrate match is possible,
the resulting TRACECLKIN/Prescaler already has a 3% deviation.
For example, TRACECLKIN=88000000, SWO_baudrate=500000,
calculate_swo_prescaler will return Prescaler=171.
The correct value should be Prescaler=176 (TPIU_ACPR=175).
Might be related to https://sourceforge.net/p/openocd/tickets/263/
Change-Id: Ib4d6df6e34685a9be4c2995cb500b2411c76e39b
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5807
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32H72x/73x flash is similar to STM32H74x/75x,
except STM32H72x/73x devices have only one single flash bank.
Change-Id: I3d3422dc60234f8273172924f426200210f388cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5792
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This change could be used within OpenOCD GitHub forks.
Once workflow actions are enabled in the GitHub project, this workflow
will be run automatically on each push into OpenOCD.
This workflow will provide a neutral build of openocd for win32, then
the package will be available for download in Actions section.
Note: the artifact will be deleted after 90 day (actual GitHub rules)
If the push is a tag, the generated package will be uploaded to release
pane under the corresponding release, and it will resides forever.
The built openocd enables libusb1, hidapi and libftdi adapters,
and could be extended to cover more adapters and Oses
PS: ./contrib/cross-build.sh updated to build libftdi from source like
libusb1 and hidapi.
Change-Id: I290c8aa14a12548e2dcb6a0eee456430ea44ab9f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5594
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
Change-Id: I2938e333bd1eac5218bd67aefb9d8f373da017a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5810
Tested-by: jenkins
The prompt pointer in the jtag serial port is never zero'd or allocated.
Completely remove it since there is not much use for it as the target
software will provide the actual prompt.
Change-Id: Id95d8ccb9f725e53b9d03386b11d91eba1cd6ef4
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-on: http://openocd.zylin.com/4093
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: If10a0f1c254aee302b9ca08958390b7f21cdb21b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5824
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: Idbc301b34fab19e221131d232577c1629568e6ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5823
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: I691094a6395acb0e4ea3bea2347ff38379002464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5822
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change-Id: I4de49bf02c9e37b72240224c23fc83abe8a4fa83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5819
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
While there, fix prototype mismatch between header and C file of
the function armv7a_l1_d_cache_inval_virt().
Change-Id: I434bd241fa5c38e0c15d22cda2295097050067f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5818
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change the type of variable retval in 'nor/ambiqmicro.c' to match
both the value to carry and the returned type of the function.
Fix the prototype mismatch of function lpc2900_address2sector()
between the header and the C file.
Change-Id: I68ffba9bd83eec8132f83bff3af993861fd09d84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5816
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change the prototype of detect_swo_freq_and_prescaler() in
'jlink.c' to avoid an implicit cast in the caller function.
Change the type of the variable retlen in some functions in
'usb_blaster.c' to properly pass their pointer to the local read
and write functions.
Use the proper parser COMMAND_PARSE_NUMBER(u32, ...).
Change-Id: I5227dbce04ee59881f173724db90790b7b9cc7af
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5815
Tested-by: jenkins
In several cases the 'int' status value returned by libusb and by
aice internal functions is taken in a variable of type 'int32_t',
requiring an implicit (but trivial) cast.
This makes compulsory using 'PRId32' in the format strings that
print such 'int32_t' result and requires an additional implicit
conversion to return the 'int32_t' as 'int'.
Replace to type 'int' all the occurrences of 'int32_t result' and
fix accordingly the format strings.
Plus, all the size of aice commands are stored as int32_t const
variables with uppercase name, violating the coding style, and are
then passed as 'int' parameter to the read/write functions.
Replace the variables with C macros carrying an 'int' value.
While there, replace also a 'uint32_t' loop index with 'unsigned'
and fix the format string in the loop.
Change-Id: Ic57d58770f1af95f003b5a02fbcb7c926ec06fd1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5814
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
While there replace a sequence malloc(size)+memset(,0,size) with a
calloc(1,size).
Replace a pointer assignment to '0' with an assignment to NULL.
In server/*, an error is logged if the ptr was already NULL. This
cannot happen since the pointer was already referenced few lines
before and openocd would have been already SIGSEGV in that case,
so remove the log.
Change-Id: I10822029fe8390b59edff4070575bf7f754e44ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5808
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
There are cases where the pointer is set to NULL after free(), but
then re-assigned within few lines. Drop the setting to NULL when
this is evident. Anyway, the compiler will remove the useless
assignment so no reason to be too much aggressive in this change.
Change-Id: I55b2ce7cbe201410016398933e34d33a4b66e30b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5811
Tested-by: jenkins
Commit 11019a824d ("adi_v5: enforce check on AP number value")
introduces the macro DP_APSEL_MAX and use it in place of hardcoded
magic numbers for the upper limit of AP selection value.
Use the macro also while defining the array of struct adiv5_ap in
struct adiv5_dap.
Change-Id: I88f53ceb710f92a48a8026a365709fbf2d9e6912
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5806
Tested-by: jenkins
All the HLA transports (hla_swd and hla_jtag) register the same
set of commands. Such commands are mainly aimed at handling JTAG
compatibility that is required for the transport hla_jtag only.
Split per transport the command registration and limit the
commands to only those required by the transport itself.
Replace the command "hla newtap" with the transport specific
"swd newdap" or "jtag newtap".
Deprecate the command "hla".
Change-Id: I79c78fa97b707482608516d3824151a4d07644c0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4877
Tested-by: jenkins
A JTAG TAP for boundary scan should be added in the scan chain
through the command "jtag newtap".
In some TCL target script the boundary scan TAP is added through
the command "swj_newdap", command that is inappropriate in this
context because specific for arm adi-v5 SWJ-DP.
This situation was probably created to bypass the error with HLA
framework, caused by missing command "jtag newtap".
Add the command "jtag newtap" in HLA, by reusing the existing
code for command "hla newtap".
Fix the TCL target scripts to use the command "jtag newtap" for
the boundary scan TAPs.
The TCL script target/psoc6.cfg has no evident reference to HLA,
so the reason for using "swj_newdap" is less clear. Nevertheless
it uses the wrong command and, once HLA is fixed, there is no
reason to avoid fixing it too.
Change-Id: Ia92f8221430cf6f3d2c34294e22e5e18963bb88c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4873
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are cases where LOG_*() functions are called before the logs
are initialized with log_init().
E.g. in transport_register() that is executed in gcc constructors,
thus called even before main().
With debug_level set to LOG_LVL_USER=-1 all the LOG_ERROR() get
dropped.
Properly initializing debug_level cause segmentation fault due to
log_output still not initialized.
Initialize debug_level to LOG_LVL_INFO so errors get printed.
Handle separately the case of log_output still NULL, meaning that
log_init() is not called yet.
Change-Id: I2ea32c87a4955fb44e79b38131c456e25dfbc327
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5602
Tested-by: jenkins
The warning message should be printed if the target is NOT halted, not
if it IS halted.
Change-Id: I0a38292a8a2e20e4a4a5ada92b475d551d4cbf38
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5794
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The "Corvette-F1" is an Arduino-compatible evaluation platform,
which fully supports AndesCore. The board has FTDI FT2232 to
connected to FPGA's JTAG interface.
The "ADP-XC7KFF676" is a development and prototyping board that
provides capacity for evaluation of AndesCore processors.
It works with AICE in-circuit debugging tools.
This patch also include target/nds32v5.cfg to support AndesCore
N22/N25F and AndeShape Platform AE250.
Change-Id: I144d5063d5086d00ec44634a5028b5ea5d2eba33
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/5338
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Either of protect and protect_check driver callbacks can be NULL. In
virtual_protect, reuse flash_driver_protect which checks for that case
and generates a nice error message and return code. In
virtual_protect_check, there is no corresponding flash_driver_*
function, so add the NULL check directly.
Change-Id: Ia63d85ede640a8382cf5cad0760f5d1ffe4d7cfe
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5782
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I06a8344d0ed62de7a0f3e2dd8fba69b17eeb3626
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5783
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There are failure cases of target_create() that are not checked.
Plus, in case of failure the memory allocated in not properly
released before returning error.
Check all the possible failure in target_create().
Change current_target only when target is successfully created.
Add the new target to all_targets list only when target is
successfully created.
Release all the allocated memory before quit on failure.
Use malloc() instead of calloc() for target->type, because the
struct will be fully populated with memcpy().
Change-Id: Ib6f91cbb50c28878e7c73dc070b17b8d7d4e902f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5776
Tested-by: jenkins
If the target is not examined, many internal data required for the
gdb connections are not ready nor allocated. This causes OpenOCD
to hit a segmentation fault.
After the execution of the gdb-attach event handler, check if
target has been examined and eventually return error to refuse the
gdb connection.
Plus, since OpenOCD does not implements non-stop mode yet, gdb
expects the target to be halted by the inferior when the
connection is established.
Print a warning to inform the user in case the target is not
halted, but still accept the gdb connection to permit the
non-intrusive memory inspection with gdb, as explained in
http://openocd.org/doc/html/GDB-and-OpenOCD.html#gdbmeminspect
Change-Id: If727d68f683c3a94e4826e8c62977de41274ceff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5201
Tested-by: jenkins
If a target is not examined when the debugger tries to connect to it
then it can lead to undesired/undefined behavior.
In particular it leads to a zero pointer dereference on the aarch64.
Change-Id: I67f2b714ab8b2727fd36f3de16d7f9017b4c55fe
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5727
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As the comment states, the 'init' command is issued before the
command 'dap apsel', otherwise it fails.
This dependency has been already fixed in commit e48690cb26
("target/arm_adi_v5: allow commands apsel and apcsw during init
phase"), so the command 'dap apsel' can now be issued directly.
Remove both the unneeded 'init' command and the comment that
documents and justify its presence.
Change-Id: I50f0a820fa7ead6f5a3bd9cc5180d521070822c9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5786
Tested-by: jenkins
There is no deinit_target method, so few memory allocations leak
at openocd exit.
Issue identified by tracking all calls to arm_dpm_setup().
Implement the method arm11_dpm_deinit() to free all the memory
allocated in arm11_dpm_init() and call it in the new
arm11_deinit_target().
NOT TESTED on real HW.
Change-Id: Icab86e290fc2db14f70eb84c8286357aadb02a35
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5694
Tested-by: jenkins
By default GDB timeouts after 2 seconds, even if this value can be
modified with GDB command "set remotetimeout".
On OpenOCD side, the default event for GDB attach is to halt the
target and wait it to halt. But here the default timeout of the
halt command is 5 seconds!
If the target cannot be halted (e.g. it's kept in reset by another
core or the debugger doesn't have enough privileges) then GDB will
timeout while OpenOCD is still waiting and is unable to
communicate with GDB.
Decrease the halt timeout to 1 second in the default GDB attach
event handler.
Change-Id: I231c740816bb6a0d74b0bc679a368a6cbfb34824
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5687
Tested-by: jenkins
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
This commit fixes support for the nEDBG CMSIS-DAP interface
which is used ie. on the Curiosity Nano SAMD21 board.
nEDBG, similarily to mEDBG, does not support 512 byte HID packets.
This patch adds its USB PID to the exclusion list to make sure that
we stick with the default 64 bytes.
Change-Id: I9010b0cf77c0b1347269a759b5d16ee5155abb16
Signed-off-by: Michal Potrzebicz <michal@elevendroids.com>
Reviewed-on: http://openocd.zylin.com/5756
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The blinking was implemented for JTAG only.
Extend it to SWD.
There is no error check on SWD exchange. Add a FIXME for further
fix.
Change-Id: I42a6708c54b1eefaf691e0fe09ca58c42b2764fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5771
Tested-by: jenkins
Bitbang interface allows having a LED on one of the GPIO.
Let also linuxgpiod driver to specify and use the LED connection.
Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
While there, replace s/return(0)/return 0/ that causes checkpatch
to fail.
Change-Id: I5ad54cffca629475563c471114a9f77301a9e4f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5768
Tested-by: jenkins
There is no method to free the register cache, allocated in
arm720t_init_target().
Issue identified by tracking all calls to arm7tdmi_init_target().
Implement the method arm720t_deinit_target() by calling directly
arm7tdmi_deinit_target().
NOT TESTED on a real arm720t target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/arm720t/ tcl/target/spear3xx.cfg
Change-Id: I53c1f46c1a355a710e8df01468b19220671569dc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5697
Tested-by: jenkins
There is no method to free the register cache, allocated in
arm7tdmi_init_target(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method arm7tdmi_deinit_target() that in turn calls
arm7tdmi_free_reg_cache().
NOT TESTED on a real arm7tdmi target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a arm7tdmi:
sed -i s/arm926ejs/arm7tdmi/ tcl/target/spear3xx.cfg
Change-Id: Iad465b708eb4ebb298725d7155fea76357e9045c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5696
Tested-by: jenkins
There is no method to free the register cache, allocated in
xscale_build_reg_cache(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method xscale_deinit_target() that in turn calls the
new xscale_free_reg_cache().
Fix leak of struct xscale.
NOT TESTED on a real xscale target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/xscale/ tcl/target/spear3xx.cfg
Change-Id: Ibb2104c42411b76f4bb77c2fa387d1b85a3d2d5d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5695
Tested-by: jenkins
Similarly to the fix for arm926ejs (also base on arm9tdmi), fix
the other targets based on arm9tdmi.
The fix for arm926ejs is tested on SPEAr320 target.
This fix is proposed separately because is not tested on a correct
target device, but tested on SPEAr320 by hacking the target type
and pretending it is the correct one, e.g.:
sed -i s/arm926ejs/arm920t/ tcl/target/spear3xx.cfg
The memory leaks detected and fixed are:
- arm register cache;
- EmbeddedICE register cache;
- arm_jtag_reset_callback internal data;
- struct <target_type>_common.
Change-Id: I565f9a5bf144a9df78474434d86a64127ef0fbe5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5699
Tested-by: jenkins
There is no flash bank support at the moment.
Change-Id: I52a2bde39425d94d9333cda002e5df0a1ef63c08
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5755
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I77e8dd161887f02ecf8019b43d3e8e7cc122ad0e
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5780
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this commit we add tcl configure files
for ARCv2 HS Development kit(HSDK). HSDK board
has Quad-core ARC HS38 CPU with L1 and L2
caches.
Change-Id: I372ef45428c7c7ca1421a6da3e5ed08b86f705e0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5784
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actionpoint mechanism allows to setup HW breakpoints and watchpoints on Synopsys ARC CPUs.
This mechanism is controlled by DEBUG register and by a set of auxilary registers.
Each actionpoint is controlled by 3 aux registers: Actionpoint(AP) match mask(AP_AMM),
AP match value(AP_AMV) and AP control(AC).
Note: some fields of actionpoint_t structure will be used in further
support of watchpoints.
Change-Id: I4efb24675f247cc19d9122501c9e63c3126fcab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The adapter NXP LPC-Link2 is a USB composite device that provides
five interfaces; among three of them that are of HID class, only
one is cmsis-dap.
Accordingly to ticket 255, OpenOCD code is not opening the right
HID interface; then it fails to communicate with the cmsis-dap
while checking the adapter's info.
Unfortunately, hidapi does not provide any support for reading the
string descriptor of the interface, otherwise it would have been
trivial to look for the right cmsis-dap interface.
In fact the cmsis-dap specification reports:
The CMSIS-DAP Firmware can be also part of a USB composite
device. If this case, the HID Interface String must
contain the sub-string CMSIS-DAP.
This requirement is satisfied by the USB device descriptor of the
LPC-Link2 reported below, but cannot be used.
Add a quirk to let OpenOCD only accept interface number zero on a
LPC-Link2 device.
Bus 001 Device 050: ID 1fc9:0090 NXP Semiconductors
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1fc9 NXP Semiconductors
idProduct 0x0090
bcdDevice 1.00
iManufacturer 1 NXP Semiconductors
iProduct 2 LPC-LINK2 CMSIS-DAP V5.224
iSerial 3 I3F4AABA
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x00ab
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 4 LPC-LINK2 CMSIS-DAP V5.224
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 7 LPC-LINK2 DATA PORT
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 1
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 0
iFunction 5 VCOM
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 5 VCOM
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 2
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 1
bSlaveInterface 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 5 VCOM
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 6 LPCSIO
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 33
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Change-Id: Ib3d46f87743a2d35a266842cb356035d898d466e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reported-by: Donald Bailey <donaldb@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/255/
Reviewed-on: http://openocd.zylin.com/5732
Tested-by: jenkins
The code in cmsis_dap_usb_open() already searches for the right
HID device that corresponds to the adapter. By calling hid_open()
it asks hidapi to re-search the adapter again based on the VID:PID
and the serial string of the adapter it has just found!
Apart from being a run-time overhead, this has an additional
drawback; there are USB adapters built as composite USB devices
that, beside the cmsis-dap HID interface, have other HID
interfaces for other purposes.
A typical example is the NXP LPC-Link2, that over the 5 interfaces
0) cmsis-dap (HID)
1) VCOM-CDC
2) VCOM-CDC
3) LPCSIO (HID)
4) LPC-LINK2 DATA PORT (HID)
has 3 of them of HID class.
The code in cmsis_dap_usb_open() could select the right interface
but then cannot propagate this information to hid_open().
Replace the call to hid_open() with hid_open_path(), passing as
parameter the "unique" path of the HID device already found.
Checking in hidapi source code, the implementation of hid_open()
consists in enumerating the HID devices, scan for the first one
matching VID:PID and serial number, and opening it by calling
hid_open_path(). This analysis highlights that using directly
hid_open_path() should not introduce any regression.
While applying these changes, move hid_init() before enumerating
the HID devices. This has no real consequences because the HID API
is marked as optional but, logically, it should be called before
any other HID API.
Change-Id: I77ec01dca64223ec597f21f188f363366d0049c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reviewed-on: http://openocd.zylin.com/5731
Tested-by: jenkins
The function perror() sends the output to stderr, but OpenOCD
cannot intercept such output to send it to the log.
Replace all occurrences of perror() with LOG_ERROR(), but keeping
the same output format of perror().
The replacement is done automatically through:
sed -i 's/perror("\([^":]*\)[: ]*")/LOG_ERROR("\1: %s", strerror(errno))/' src/jtag/drivers/*.c
Change-Id: I4c140bdb09235d56cfd8bef75da9b56fbe7c2aec
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5728
Tested-by: jenkins
The USB adapter DLN-2 provides 32 GPIO (beside I2C, SPI, ...).
Use the first 6 GPIO for a SWD/JTAG bitbanging example through
linuxgpiod driver.
Change-Id: I229c2078142ec648fc6430b5d123539045dcfbda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5561
Tested-by: jenkins
New adapter driver for GPIO bitbanging over Linux GPIO descriptors
through the library libgpiod.
On Debian based distribution, the package libgpiod-dev is required
for build.
Change-Id: I1ce1a4f1ca79096d6d476b01b523c8c10f2cac07
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5559
Tested-by: jenkins
If the configuration file specifies both SWD and JTAG gpios, the
current code request all of them. In case of overlap a warning is
generated when the same gpio is released for the second time.
Require and release only the gpio needed by the specified
transport.
Change-Id: I41a0970980ceeb559afa98ab34cfe93dffed2e1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5556
Tested-by: jenkins
The split in OpenOCD between SWD and JTAG has been already fully
implemented. The bitbang driver still keeps a single API write()
to drive the output lines.
Introduce a new SWD specific API swd_write().
Move the existing SWD bitbang drivers to the new API by extracting
the available conditional implementation.
Cleanup some function prototype.
Remove the now unused global swd_mode, handled implicitly.
Rename bitbang_exchange() as bitbang_swd_exchange() to track its
scope for SWD only.
Change-Id: Ie53080b941cb1ac7a34a1f80bad8bee4e304454d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5555
Tested-by: jenkins
The SWD framework already takes care of switching between JTAG and
SWD by calling driver's switch_seq() in swd_connect() and in
swd_quit(); there is no need for the driver to force the switch
again.
Remove the extra switch between jtag and swd.
Change-Id: I84de4bffb593374b96fce31951c6cc83f92d2578
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5554
Tested-by: jenkins
Kinetis Flash Configuration Field needs special handling to prevent unwanted
locking of the device. Warn user about any difference between generated
FCF and FCF data in the programmed file. Inform user that re-programming
of already programmed FCF may fail on devices with FTFE flash module.
While on it remove useless setting of is_erased flag after erase.
Change-Id: I3911f436674547fa12ef3886c7d5e8cd889f9e2b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: https://sourceforge.net/p/openocd/tickets/270/
Reported-by: Noel Diviney <vk3avm@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/5753
Tested-by: jenkins
Since e22c6484ea the trial/error allocation shows
"not enough working area available(requested 2048)" message
on klx.cfg. The message is not clear if it means a problem or not.
Replace with new style allocation using target_get_working_area_avail()
Change-Id: I87fe1e38248fcac29982b72aaba12217a0552f38
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5752
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In case of GDB connection not using extended mode, issue a warning
message to suggest the user to switch using the extended mode.
Issue the message only once at each run of OpenOCD, to avoid too
much noise.
Update the documentation to suggest using extended mode.
Change-Id: I9326e84f748d5d7912d5a48f00f0fb541ca19221
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5311
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_ARGUMENTS -f {} \;
This patch also fixes an incorrect function prototype in zy1000.c.
ZY1000 minidriver implementation overrides the function
arm11_run_instr_data_to_core_noack_inner(), but the prototype is
not the same as in src/target/arm11_dbgtap.c and to avoid compile
error it was changed also the prototype of the called function
arm11_run_instr_data_to_core_noack_inner_default().
Change-Id: I476cda8cdb0e1e280795b3b43ca95c40d09e4a3d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5630
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
It is an error to prefix with "0x" the print of values in decimal.
Replace the incorrect decimal format specifier with PRIx32.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types PRINTF_0XDECIMAL -f {} \;
Change-Id: I2eb867ef654527b2737ba573a405ec8f97c6a739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Current hla driver supports two "layout": stlink and ti-icdi.
The configure script allows to independently enable/disable the
the two layout. But in reality by selecting only one of them the
whole hla driver is built, including both "layouts".
This is currently not a big issue because the dependencies of the
two layout are the same (libusb), so we are sure that selecting
one of them would permit to build both.
This is going to change with the merge of a third "layout" for
Nuvoton Nu-Link, because it would be based on hidapi.
We need, at least, to decouple the build of libusb and hidapi
"layouts". A full decouple of each "layout" is also welcome to
match the selection done during configure.
Introduce a new automake macro for each of the two "layout" and
use them to conditionally build the "layout" files.
Use the existing autoconf macros to conditionally compile the code
that depends by the "layout".
Change-Id: Ia20da7a260002a8d2af883425aa401b8920d3f36
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5719
Tested-by: jenkins
The Jim_SetResultFormatted() frees jim object earlier and the
Jim_FreeNewObj() does it second time. It breaks the memory heap.
To avoid it the Jim_IncrRefCount() + Jim_DecrRefCount() should be used
instead of the Jim_FreeNewObj() call.
Change-Id: Ifa5f38009b2d617624b5f27e916720888a3dbad9
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use 'unsigned int' and 'bool' instead of 'int' where appropriate.
While at it, fix some coding style issues.
No new Clang analyzer warnings.
Change-Id: I700802c9ee81c3c7ae73108f0f8f06b15a4345f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4929
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, erasing a block can take up to 200 ms.
When using a Segger J-Link with a 2 MHz clock the current loop
finishes after < 50 ms, ignores the timeout, and then fails when
erasing the next block.
Switch to a time based check, add an explicit yield, and report an
error on timeout.
Change-Id: I8255401d1e59f427a08d2cccb8a66143dcdbb324
Signed-off-by: Michael Hope <mlhx@google.com>
Reviewed-on: http://openocd.zylin.com/5706
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit b3ce5a0ae5 ("target: use LOG_USER to print errors
in events") an error in an event handler was silently lost, while
now the associated message is printed out.
A "shutdown" command in a target event (e.g. in gdb-detach) causes
the event to end with error code ERROR_COMMAND_CLOSE_CONNECTION,
that triggers the error message:
shutdown command invoked
Error executing event <event-name> on target <target-name>:
The error code returned by the command "shutdown" is required to
stop the execution in a script/proc and avoid executing any
further command in the script/proc.
It is then normal to get an error code from the "shutdown" command
and it should not be printed out.
Intercept the return code of the event in case of "shutdown", then
skip scheduling other target events and return without printing
the incorrect error message.
Change-Id: Ia3085fb46beacb90a5e4bf0abf7c6e28bb9e6a9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Laurent Lemele <laurent.lemele@st.com>
Reviewed-on: http://openocd.zylin.com/5710
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Add support for SWD debug to the Xilinx XVC/PCIe driver.
This is possible since the device is essentially a shift-register.
So doing SWD vs JTAG is a matter of wiring things correctly on the
RTL side (use TMS for SWDI, TDO for SWDO).
The clang static checker doesn't find any new problems with this change.
Change-Id: I3959e21440cd1036769e8e56a55e601d3e4aee9a
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5447
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this commit we introduce L1 and L2 cache
flush and invalidate operations which are necessary for
getting/setting actual data during memory r/w operations.
We introduce L2 cache support, which is not presented
on currently support EMSK board. But L2 is presented
on HSDK board, which soon will be introduced.
Change-Id: I2fda505a47ecb8833cc9f5ffe24f6a4e22ab6eb0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5688
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When debugging an ARMv8-A/AArch32 target running HYP mode, OpenOCD would
throw the following error to GDB on most operations (step, set breakpoint):
cannot read system control register in this mode
The mode in question is 0x1A, a privilege level 2 mode available on cores
that have the virtualization extensions (such as the Raspi 3).
Note: this mode is only used when running in AArch32 compatibility mode.
Signed-off-by: Lucas Jenss <public@x3ro.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change-Id: Ia8673ff34c5b3eed60e24d8da57c3ca8197a60c2
Reviewed-on: http://openocd.zylin.com/5255
Tested-by: jenkins
Reviewed-by: Lucas Jenß <lucas.jenss@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This update is for testing the upcoming 0.2.0 release.
Change-Id: I400b09eb3ead4306c83c7980c621124101aaef7e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5723
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This fixes a regression introduced in "2dc88e1479f29ef0141b05bfcd907ad9a3e2d54c"
Change-Id: I04dc19ed30118a4c499b83732700b2ee0fdb67b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5610
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In addition to the debug TAPs, the ICEPick C also supports
a bank of Test TAPs (limited functionality intended for
non-debuggable targets). Added support for Test TAPs to
the icepick_c_tapenable routine. Port numbers of 0 to 15
will continue to be handled as a debug TAP number. Test
TAPs will be port numbers of 16 to 31.
This functionality will be needed for doing a flash
mass erase on CC26xx/CC13xx targets. It is possible
for user application to block even adding the Cortex M
TAP to the scan chain, so the only way to unbrick the
target and erase the flash is using a component on a
test TAP of the device's ICEPick router.
Change-Id: I0aa52a08d43a00cbd396efdeadd504fc31c98510
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5715
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Issue: server_quit is called before adapter_quit:
In WIN32 only in server_quit we do an WSACleanup,
which terminates/closes all active sockets.
So if the adapter is TCP based, the adapter.quit handler
will fail if it will need to send some commands through TCP.
Example: close_socket in jtag_vpi_quit will fail in WIN32
because the socket is already closed
and the errno is set as "Bad File Descriptor"
To fix that we introduced new functions called server_host_os_entry/quit
to manage specific OS setup (hence WSA for sockets in WINDOWS) in order
to delay WSACleanup after adapter_quit().
Change-Id: Ie4afacafe123857f6ae300e376bdfcf0d8c027ac
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5456
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MULTILINE_DEREFERENCE -f {} \;
Change-Id: Icba05613e22a72ecc3e6a0aad7cb6b479496146f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5629
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
If the function parse_u64() fails, we jump to return, thus leaking
the memory just allocated in 'v'.
Issue identified by clang.
Move earlier the call to parse_u64() and the associated test,
before memory allocation.
While there, fix a possible NULL pointer dereferencing in case the
calloc() fails, by testing for allocation failure.
Change-Id: I6a77ee17aceb282bbdfefe7cdafeba2e0e7012f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5692
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
There is no method to free the register cache, allocated in
armv4_5, so we get a memory leak.
Issue identified by valgrind.
Implement the method arm_free_reg_cache() and call it in cortex_a
deinit and to exit for error during arm_dpm_setup().
Tested on dual cortex-A stm32mp15x.
This change is inspired from similar fix in commit b01b5fe13a
("armv7m: Fix memory leak in register caching.").
The same allocation is also used by target types "arm7tdmi",
"arm9tdmi", "arm11" and "xscale" but they all lack the deinit
method and I do not have relevant HW to test the fix. For such
reasons they are not addressed in this patch.
Change-Id: I4da1e1f12e36ec245d1f3b11a4eafcbd9a1d2e25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5693
Tested-by: jenkins
The target mem_ap misses the method 'deinit_target' and does not
free the memory allocated during 'target create' and 'configure'.
Add the missing method and free the allocated memory.
Issue identified with valgrind.
Change-Id: If0d0114a75dd76a8b65c2d46d96c6085fd31a09d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5700
Tested-by: jenkins
When jtag_libusb_open() fails to find the adapter, it returns
error but left libusb initialized causing memory leak of libusb
internal data.
Issue found with valgrind when no adapter or board is connected to
the host, e.g.
valgrind openocd -f board/st_nucleo_f4.cfg
Close the libusb operations if jtag_libusb_open() has to return
error.
Change-Id: Ieb2f110be15705dafe80c099e7d83c07056c2a41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5701
Tested-by: jenkins
Current code for Cortex M does not set C_DEBUGEN as soon as
possible, (which means during target examine), but later-on either:
1) at command 'halt' (e.g. for 'gdb-attach' event);
2) at command 'soft_reset_halt';
3) at commands 'reset', 'reset halt' or 'reset init';
4) during polling, but only if the target:
= enter in 'double fault', or
= exit from a reset, or
= halts (not possible if C_DEBUGEN is not set)
Plus, if commands in 1) or 2) are executed before the very first
poll of the target, the value of 'cortex_m->dcb_dhcsr' is used not
initialized while writing it back in DCB_DHCSR.
Another side effect of this situation is that it's possible to set
a HW breakpoint with the target running, while C_DEBUGEN is not
set. Accordingly to [1], C1.3.1 "Debug authentication":
When DGBEN is LOW and DHCSR.S_HALT == 0:
...
FPB breakpoints do not generate an entry to Debug state and,
if no DebugMonitor exception is generated, will escalate to
HardFault, Lockup, or be ignored.
On STM32MP15x I get HW breakpoint ignored, while on STM32F411 I
get HardFault.
E.g. following these steps:
- power-on a pre-flashed board that starts running the firmware;
- connect openocd, without halting or resetting the board;
- set a HW breakpoint to some address often executed;
- wait, but the board doesn't halt ...;
- type the command 'halt';
- if the Cortex-M has HardFault it would be visible and the fault
is at the breakpoint address;
- if no HardFault then type the command 'resume';
- wait and the board will finally halt at the HW breakpoint.
A similar issue has been detected on Cortex-A code and fixed by
commit bff87a7f28 ("target/cortex_a: enable DSCR_HALT_DBG_MODE
during examine").
Follow the same approach and set C_DEBUGEN during examine.
Also, initialize 'cortex_m->dcb_dhcsr' during examine.
[1] ARM DDI 0403E "ARM v7-M Architecture Reference Manual"
Change-Id: I5b0b23403634f7dfce38f104bba9f59c33eb3e99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5702
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Moritz Fischer <moritzf@google.com>
The kept_alive() function is called to inform the keep-alive code
that a keep-alive as been just kicked through some other path.
But kept_alive() erroneously resets the timeout counter without
checking if it has already expired, thus masking a potential
timeout.
Check if timeout counter has expired during kept_alive().
While there, put the timeout values in macros and explicit the
units in the timeout messages.
Change-Id: Iaf6368b44e5b5352b1cc4e7efbb2368575dcfa08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5705
Reviewed-by: <jonatan_zeidler@gmx.de>
Tested-by: jenkins
Flashing Kinetis MCU MK22FX512VLH12 takes longer than one second,
thus gdb connection can timeout. Before commit 7f260f5009
("helper/command: Handle Tcl return values consistently") the
openocd timeout warning was masked by a bug in gdb_put_packet()
that resets the timeout counter if any message is logged out.
The commit above removes one log message and the timeout warning
is now triggered.
While the bug in gdb_put_packet() is still to be fixed, the reason
of the timeout is the lack of keep_alive() calls in kinetis flash
driver.
Add keep_alive() call at every iteration in function
kinetis_write_sections(), that is reported as core write function
in chunks of 1024 bytes in the log from the reporter.
Add also a keep_alive() call at every iteration in function
kinetis_write_inner(). This part is not present in the log but, by
code analysis, it represents another critical loop.
Change-Id: I38e631b36c7eb2f1e21cef68710ce47c03d3edda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Jonatan Hatakeyama Zeidler <jonatan.zeidler@medineering.de>
Reviewed-on: http://openocd.zylin.com/5703
Tested-by: jenkins
Reviewed-by: <jonatan_zeidler@gmx.de>
use handle_command_parse_bool within dap_ti_be_32_quirks_command to make
it shorter and simpler.
Change-Id: Ice179cc477933b27e27235dc2ade23fe655e233d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5708
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
avoid the usage of ERROR_COMMAND_SYNTAX_ERROR when
ERROR_COMMAND_ARGUMENT_INVALID is more adequate.
Change-Id: Ic9aaedb93fedd45efee1b39f8ea20185f01af2da
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5654
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For jtag/drivers/bcm2835gpio dev_mem_fd has been updated within
bcm2835gpio_init with the add on of gpio to mem. This permits the
access to memory of GPIO without the need for root access.
For failed attempt, a fallback to original memory follows.
It should be noted that any printed error is relative to original
memory ("dev/mem").
Tested on EFM32GG12B390F board
Change-Id: I4540bdf62fb3b91a51221e277881adfae138dcc5
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5568
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: If7465a752f47f3292e430c8b311148badfd384cd
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5478
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I13871ec13709055843e23b1b6da90694fd60505e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5477
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I30fcb8f291d401acaa1fe665db0eeabc250d24b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5476
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While I'm hoping to maintain the chain of redirects for the foreseeable
future, it makes sense to point at the final URL now that Autotools
Mythuster has had its domain for a long while.
Change-Id: I6d912e3be0f81b25bec14746ebfee58f29f144b6
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Reviewed-on: http://openocd.zylin.com/5709
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The function command_find_in_parent() is never used in OpenOCD, so
remove it.
The functions command_name() and [un]register_command() are only
used internally in command.c, so make them static.
Change-Id: Ide9842659796f4884fb6c1fcf5979b3b71b67abb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5663
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The jim library exports all the data types through typedef, so
there is no need to use the internal struct types.
Fix the few remaining inconsistencies in the code.
Change-Id: Id4ae0083563ea7a371833374e7b39f17158f66a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5662
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Either Jim_CreateCommand() and register_command_handler() return
the jim error code JIM_OK/JIM_ERR.
Fix the check and the initialization of retval.
Change-Id: I3073c66764670128706ad979a43bb3edbbeb0ab0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5661
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
After commit 0840414f0e ("helper/command: do not replace new
commands with ocd_ prefix"), the command name is present in
argv[0], so there is no need to pass it directly. The current code
causes the command name to be logged twice, once explicitly and
then from the content of argv[0]:
openocd -c 'debug_level 3; echo hello; shutdown'
<snip>
Debug: 13 3 command.c:142 script_debug(): command - echo echo hello
<snip>
Debug: 16 4 command.c:142 script_debug(): command - shutdown shutdown
Remove the command name from the arguments of the function
script_debug().
Change-Id: I57860774f450ff717ee71ef9dc07590549a84319
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5660
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The new stlink firmware requires opening the AP before issuing
any operation.
In the current code we have a 'questionable' check about the core
model to set the TAR autoincrement, that is issued without opening
the AP, thus causing a STLINK_BAD_AP_ERROR.
Modify the AP open API to handle this case and open AP#0 before
the memory access to check the core model.
Change-Id: I576955b5094bd41d63ff1fbad7b4fd9433253321
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5691
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Firmware v2j28 introduces the API to open and close the AP, but
closing AP always returns error 0x1d (STLINK_BAD_AP_ERROR).
Ignore the error returned by the bogus firmware on closing AP.
Change-Id: I992ddbf7acb10f1d376ed8f781eeb3344605b85d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5683
Tested-by: jenkins
When the transport is not specified, OpenOCD uses the first listed
by the selected adapter driver.
The old HLA driver for stlink lists SWD as first. The new driver
dapdirect instead lists JTAG, making more difficult a fallback to
HLA when dapdirect is not available due to old stlink FW.
Plus, in case of JTAG wiring, SWD is still possible, while the
opposite is not.
Reorder the list of transports to grant the default to SWD.
Change-Id: Id9c529e921b148d5b352d4603a9028c2a5f15d83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5538
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Previously the adapter speed settings were hard-coded to
connect with low speed then switch over to high speed
regardless what was mentioned in the cfg files. Now the
stm8 target intercept adapter speed settings and configure
the stm8 control registers accordingly.
Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The transport SWIM is selected twice, in board and in target, thus
a warning is generated at run-time. It should be fixed by remove a
line in the target file, but does not harm so let's keep it there
for the time being.
Change-Id: I479004dc16005a330d552c8dbd5def61690f9b9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5543
Tested-by: jenkins
No reason to keep longer this temporary hack.
Remove it by reverting the original commit.
Change-Id: I5c6dcdb1f4755b7dba4c03a5033913ef8db35e18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5533
Tested-by: jenkins
Now that SWIM is not accessed through HLA anymore, decouple the
SWIM code and remove the conditional execution.
Fix the inconsistency of the return type for stlink_usb_state() in
case of SWIM (returns ERROR_OK while type is enum target_state)
introduced by commit 3de6b5f6e5 ("jtag/drivers/stlink_usb :
implemented and repaired SWIM support").
The code added by commit above in stlink_usb_state() is an hack to
reuse existing HLA API to perform a reconnect.
Move the SWIM specific code from stlink_usb_state() to a dedicated
stlink_swim_op_reconnect() that provides consistent data type.
Change-Id: I3fe175fef00b0735bea6139b057f217a080c9d38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 3de6b5f6e5 ("jtag/drivers/stlink_usb : implemented and repaired SWIM support")
Reviewed-on: http://openocd.zylin.com/5532
Tested-by: jenkins
Thanks to API separation between SWIM and the other transports, we
can easily split the memory read/write for SWIM from the rest of
the code.
While there, use the macro STLINK_DATA_SIZE as size of data chunks
that can be read/write in SWIM. This was not implemented before.
Change-Id: I7d913c92539007e4d914480bacc0126a8f0e9705
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5531
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
SWIM is implemented by (ab)using the HLA API. This was acceptable
when OpenOCD code did not provided a clear separation between
transports and related APIs. Still today SWIM in OpenOCD is only
supported by STLink, so the decision to re-use the HLA API was the
simpler way to implement it.
After commit efd1d64222 ("adapter: switch from struct
jtag_interface to adapter_driver") the transports API are better
split and SWIM can be implemented as a separate set of API. This
would open the possibility to extend OpenOCD for other adapters
that provide SWIM, e.g. versaloon, or through SPI emulation [1].
Introduce a new set of files swim.[ch] to handle the SWIM API.
Beside the API that almost match the transport low-level data
communication (system_reset, read_mem, write_mem), add a further
API reconnect. Today, inside HLA STLink code, the reconnect is
implemented by hacking the HLA API state(). Please notice that
due to this hack the return type is incorrect; stlink_usb_state()
returns ERROR_OK in SWIM mode, while its return type is enum
target_state. Ignore the type mismatch and still call the HLA API
state in the new SWIM API reconnect. Further commit will fix it.
[1] http://kuku.eu.org/?projects/stm8spi/stm8spi
Change-Id: I52018e1e2200cbd41af8e5031f7b35dc761b61d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5528
Tested-by: jenkins
The transition of STM8/SWIM out of HLA will require a new struct
swim_ops in struct adapter_driver.
To simplify the development, make the HLA interface temporarily
accessible through the struct adapter_driver.
This commit will be reverted after the swim rework.
Change-Id: I1e4f370cf64641164d7bcaa22f75ac58c9240052
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5527
Tested-by: jenkins
In the driver's code it's widely used the enum hl_transports for
any check concerning the current transport, even for the non-hla
transport dapdirect.
The driver already provides a stlink specific enum stlink_mode
that can be used in place of the hla one.
Replace the hla enum with the stlink one allover the code.
Introduce a hla specific wrapper stlink_usb_hl_open() to cope with
the only API that requires the hla specific enum.
The overall behaviour is not changed, with exception for a debug
message in stlink_usb_open() than now prints the numeric value of
stlink enum in place of the numeric value of the corresponding hla
one.
This change prepares the road for moving SWIM transport out of hla
by removing any reference to the macro HL_TRANSPORT_SWIM from the
stlink driver.
Change-Id: Ieeea34f312245a94bfc1333087afdb8eb9f77139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5526
Tested-by: jenkins
Commit da41bce3ae ("target/arc: introduce breakpoint
functionality") introduces a mismatch between the format string
and one int constant.
Change the format string to match the int constant.
Change-Id: I0d59552205551b90e165c0a2e3fef247ad0c7701
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: da41bce3ae ("target/arc: introduce breakpoint functionality")
Reviewed-on: http://openocd.zylin.com/5655
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Expression like (0xffff << 16) evaluate to type int, which is not able
to hold that value, producing a warning when compiling with
-fsanitize=undefined. This patch makes most of the cortex_m constants
unsigned using the BIT() macro or appending "ul" when possible to fix
the undefined behavior warning.
Signed-off-by: iosabi <iosabi@protonmail.com>
Change-Id: I7af194305ef612d7a32e74eaf9f11dd85fa87f32
Reviewed-on: http://openocd.zylin.com/5583
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types OPEN_BRACE -f {} \;
Change-Id: I6d1356ed11e2699525f384efb7556bc2efdc299f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5628
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The coding style is quite permissive allowing 120 chars per line,
but abuses are still present.
Fix them, wrapping the lines.
Change-Id: I94d66b651d759a60ec35f7ba115c43933e70ed69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5626
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The re is no need to split a long string, apart for fitting the
predefined line width.
Join the consecutive string fragments.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types STRING_FRAGMENTS -f {} \;
Change-Id: I8de52d572b0e3d4788c1d4d2b0cf8f94c7f08409
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5625
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The statement "else" should not be on a new line when follows a
close brace '}'. Fix it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ELSE_AFTER_BRACE -f {} \;
Change-Id: I8af247ec3f75a69713d7cb1e73881254d16c189e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5623
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
For void functions, a return as last statement is useless.
Remove it.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types RETURN_VOID -f {} \;
Change-Id: Ie0616fe98623f30d2d7b04ac9517d669774092de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5622
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Functions that have no parameters should use "void" as parameter
in the function declaration.
Issue identified and fixed by script checkpatch from Linux kernel
v5.1 using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_WITHOUT_ARGS --fix-inplace -f {} \;
Change-Id: If104ac75b44e939ec86155ff7b5720f2e33c6b39
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5621
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TRAILING_WHITESPACE --fix-inplace -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5616
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5615
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find doc/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I1269ac966027439e16eb6e63179e43925bec37fa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5614
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Commit 87a4158acf ("drivers: xds110: Clean up command syntax and
documentation") does not follow the documentation structure that
lists the adapters in cpt 2 "Debug Adapter Hardware" then lists
the adapter commands in cpt 8.2 "Interface Drivers"; it puts all
in cpt 2.
While doing that, uses an incorrect texinfo syntax that causes the
following warnings at compile time:
doc/openocd.texi:543: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:547: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:552: warning: @deffn should only appear at the beginning of a line
Move the documentation of xds110 commands in the proper chapter
and fix the texinfo syntax.
Change-Id: I0b3f0fe0c687f194bb02e2d81aca86fcd4fdd718
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 87a4158acf ("drivers: xds110: Clean up command syntax and documentation")
Reviewed-on: http://openocd.zylin.com/5613
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Edward Fewell <efewell@ti.com>
Starting from version 8, gcc issues a warning if strncpy could be
able to truncate a string (so without adding the zero-termination
char in destination) by copying exactly "size" char from a source
string not shorter than "size".
Such truncation from strncpy could actually be the desired code
behaviour, but the way to silent gcc only locally (without global
disabling with -Wno-stringop-truncation) through pragma has other
side effects on portability.
In current code, the source string is always "eth0", because has
been checked right above. So this is a false positive from gcc,
being always strlen("eth0") < 16, the sizeof(ifreq.ifr_name).
Silent gcc by decrementing the "size" and remove:
error: ‘strncpy’ specified bound 16 equals destination
size [-Werror=stringop-truncation]
This file is only optionally compiled together with ZY1000 driver
with --enable-zy1000 --enable-ioutil. This combination is not
checked in jenkins, so the error passed unnoticed.
Plus, the configure flags above are both deprecated!
Change-Id: I229e66227cfd3513139feeaffa47a6e1ec00767b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5631
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The commands "ocd_find" and "capture" are registered directly
through the jim API, instead of the common way to describe them
in a struct command_registration that is then passed to the helper
register_commands().
This cause the two commands above to not have either "help" nor
"usage" string nor a properly identified "mode".
Since the following line registers the commands listed in struct
command_builtin_handlers, simply add the two commands above in the
same struct.
Change-Id: Id6ee11dac3b18364deeed65ee8e18ad80152750a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5644
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The state machine of cortex-m have to pass through a set of state
before it get in "halted".
Add one more "arp_poll" to achieve the proper state during a
"reset halt" command in engineering boot.
Change-Id: I90828bf20ef75bd4018f8b911f727ae69c4d6e8f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5649
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
With this patch we introduce set/unset breakpoints
routines and add/remove bp handlers.
Currently soft breakpoints are only supported.
Changes since v1:
* Change if-statement in arc_remove_breakpoint
* Squash changes from http://openocd.zylin.com/#/c/5641/
in this commit to fix build.
Change-Id: Ib10ccdb02fd1606e4f407f012b1bee106a8ffccd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5641
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This commit introduces helper instruction read/write functions
for further bp functionality.
Change-Id: I619fbe2870ef6365c29ed1618bb83b6f7eb84690
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5640
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
get_thread_reg() allows gdb to request the register value of a specific
"thread."
set_reg() allows register writes without getting a giant list of
registers first.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I87faa1c8793916b9ee476dd696f0695a07ca2b41
Reviewed-on: http://openocd.zylin.com/5324
Tested-by: jenkins
this change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
a table with register offset will be introduced, thus correct register
addresses will be obtained using this table and the driver internal
function 'stm32l4_get_flash_reg' will be responsible of this.
Change-Id: I74bf61a83fe53575623640af0328b3253ecc796f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5508
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Michael Jung <mijung@gmx.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to RM0432 rev. 6, only 0x1001 "Z" rev. applies for STM32L4P5/Q5.
Verified on real device. Whether other revisions exist is unclear.
Change-Id: I761ae077d089b06925fc0fe1ff2b1e478b8a66fa
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5521
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Introduce a variable 'size' and reduce the number of dereferencing
*reg_list_size by using the variable.
Change-Id: I3bdf1485a4ed8e34435e8acb3efd0df8d802508c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit c2cecc74b0 ("Move JTAG interface list to new files.")
merged in mid 2009 introduces an unused and empty function that
the developer expects to use for loading adapter drivers from
shared libraries. This have never happened and the function is
still empty and unused.
Remove it.
Change-Id: I7c88dbf8a9747e96e5ca4e6e7038ac0f232604fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5601
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
All the servers open the listening socket during openocd "init";
it's not possible to change the tcp port or the bind address
after "init".
In current code, the call order during "init" permits to change
the port and bind address of tcl and telnet server if the related
command is issued after "init" in the same script or on openocd
command line. This is not guaranteed to work if the call order
during "init" changes, so it's incorrect.
Change the commands "bindto" and "*_port" to COMMAND_CONFIG.
Change-Id: Id88f225a67a872b4bcaf3b799466bddedc248015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Christopher Head <chead@zaber.com>
Fixes: https://sourceforge.net/p/openocd/tickets/264/
Reviewed-on: http://openocd.zylin.com/5595
Reviewed-by: Christopher Head <chead@zaber.com>
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I4efbd9af5be7e16213dcc7cb95de936ecde2fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5173
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
Fix build error on Mac OS X Catalina (10.15.4) caused by formatting
stm32l4_info->wrpxxr_mask, which is uint32_t, as uint16_t in the debug
log message. Adding casting to uint16_t before substitution because only
lower 16 bits are significant for debug purposes.
Change-Id: Iddb87cd156dfc84ab1f91cd15a1ddee6b646d412
Signed-off-by: Ilya Kharin <akscram@gmail.com>
Reviewed-on: http://openocd.zylin.com/5590
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By default the list of VID/PID is empty so if ftdi_vid_pid is not called
then no matches are attempted. The only message is at -d3:
Command 'init' failed with error code -100"
Check for this condition explicitly to make life easier for people
configuring adapters.
Change-Id: If0f93370c9e9ddc9700aae7c346c1c6dd319152e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5440
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce a new ERROR_TARGET_ALGO_EXIT as currently used
ERROR_TARGET_TIMEOUT should be reserved for the timeout only.
Do not load PC directly from CPU HW as the register value
has already been cached.
Change-Id: I0d3630da41fd021676789dc12b52545cc0432ba8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5329
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Some flash banks are not mapped in the target memory
(e.g. SPI flash, some special pages).
Add flash version of mdw/h/b which reads data using
the flash driver.
Change-Id: I66910e0a69cf523fe5ca1ed6ce7b9e8e176aef4a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4776
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If watchdog is enabled, there's no way we can disable it while the flashing firmware
is running. (Halt disables it, but software reset doesn't.) So let's have the flashing
firmware refresh the watchdog regularly, in case it has been enabled by previously
running software. Failure to do so could lead to a watchdog reset in the middle of
the chip bieng programmed.
Change-Id: I79d41593948aae0080480e891552e1c2ee3ccbd0
Signed-off-by: Aurélien Martin <martaurel@gmail.com>
Reviewed-on: http://openocd.zylin.com/5266
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
BUILD_TARGET64 creates a larger test matrix and mostly gates the
building of the aarch64/armv8 target, make that unconditional, which
would help fixing any issues with 64-bit address types anyway.
Rebased by Antonio Borneo after commit 1fbe8450a9 ("mips: Add
MIPS64 support")
Change-Id: I219f62b744d540d9dde9a42e6b63fd7d91df3dbb
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5240
Tested-by: jenkins
This is a follow-up change of commit 6d6a69d5 to disable it by
default. The driver was introduced in 6d6a69d5 and enabled by
default in order to run the jenkins build.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Change-Id: I5c5fc6711b971b65dd5846a6163025879044ec40
Reviewed-on: http://openocd.zylin.com/5563
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit c5d8988316 ("checkpatch.pl:
check for openocd tree, not for kernel tree") has already fixed
the check for OpenOCD tree, thus we do not need to skip it in the
shell wrapper.
Remove flag --no-tree from the shell wrapper.
Change-Id: I8be497258624d89bde7742fee141a8f56bf9188e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5110
Tested-by: jenkins
Drop bogus reference to board/renesas_gen2_common.cfg , which is a
non-existing file.
Fixes: a01474bb4c ("tcl/target: Switch Renesas R-Car Gen2 boards to new config")
Change-Id: Icb22d8456b7ac94d3a9a4ed354b246ee1332b122
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5564
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The stm32mp15x has one or two Cortex-A7 (depending on the P/N) and
one Cortex-M4.
The second core is automatically detected by the target script.
In "engineering boot" all the cores are accessible.
In "production boot" the Cortex-M4 is kept in reset state after
power-on or NRST.
The board DK2 includes a ST-Link/V2, but only SWD is connected.
Change-Id: Ib6ebefcc696b1716e0f98694cadf0b04fd7d11d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5454
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1075
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1275
ulink_append_xxx_cmd() functions allocate memory for cmd
and then call ulink_allocate_payload(), which allocates cmd->payload_out
or cmd->payload_in.
ulink_append_queue() checks the size of queue and if the new payload
does not fit, calls ulink_execute_queued_commands() and then
ulink_post_process_queue(). If any of these two fails, an error is
returned, allocated cmd struct leaks and the queue is left in an undefined
state.
Change ulink_append_queue() flow to proceed to appending cmd to the queue
even in the case of fail in previous ulink_execute_queued_commands()
or ulink_post_process_queue(). In case of fail then clear the queue
including the last appended cmd.
Change-Id: I967c07af19e9020c93bcb4ef403cf1f557dd1db1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5370
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Access to field 'payload_in' results in a dereference
of a null pointer (loaded from field 'queue_start')
File: src/jtag/drivers/ulink.c
Line: 2216
Set input/output_signals conditionally if ulink_append_get_signals_cmd()
and ulink_execute_queued_commands() returns no error.
Do not fail driver initialisation as the signals are only printed.
Change-Id: I6c842f0e9a604712abf7444a2fa95ba5810de1ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5520
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
core.c:446:
The left operand of '>>' is a garbage value
There are many places where an error code returned from nand->controller
operations are ignored. To keep the change minimal, the error checks are
added only to reading of extended nand info as it was suspected
to be the cause of the warning.
Addition of the error checks did not fix the warning.
scan-build-9 report was inspected and IMHO the warning is bogus:
the term (nand->device->erase_size == 0) cannot give false at line 395
and then evaluate true at line 462. Fixed by zeroing id_buff.
Change-Id: I97ed7ce0fdf1aa23d746d5fb898bacd050e20ae8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5518
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In arc_poll() function we handle the cases, when jtag indicates, that
processor is halted, but target->state is not TARGET_HALTED.
In case, when processor was halted and target->state was TARGET_RUNNING,
we should save context. At the same time if target->state was TARGET_RESET
we do not need to save context.
Changes: 16.04:
Fix - Move setting target->state = TARGET_HALT after
"target->state == TARGET_RUNNIG" check, otherwise
this check makes no sense
Change-Id: I92ab6ec71cf58273bb8401d14a562035de3deab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5524
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
28.02.2020:
-Removed multiple cpu configuration section, currently
only ARC EM is supported.
17.03.2020:
-Some cleanup
-For "arc set-reg-exists" command limitize the number of
arguments (50 maximum).
17.03.2020(v2):
-Revert limitation for "arc set-reg-exist" command
Change-Id: I4b06f89df95f2773bfde6e1bd2ae2b6b880bfaa8
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5351
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With this commit we add tcl files which describes
ARCv2 architecture features and configure files
for ARCv2 EMSK board.
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
Changes:
22.01.2020:
-Removed "actionpoints" handling code in
tcl/cpu/arc/v2.tcl because this capability
is not supported yet.
Changes:
17.03.2020:
-Update Licence headers
-Cleanup indents
-Removed "reset halt" in boards .tcl
-Updated adapter frequency commands
Changes:
15.03.2020:
-Removed "init" in the of boards .tcl
Change-Id: I51bf620abe7b8e046e1dccc861a7d963965d3a42
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5350
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This reverts commit 6568d29cc1.
The reverted change caused some tasks were missing in thread list.
While on it add a comment explaining the relation of uxTopUsedPriority
and configMAX_PRIORITIES, introduce config_max_priorities and
change types to unsigned.
Change-Id: I4371c8882470d13ee7360ef21b132c56ecb95af8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5577
Tested-by: jenkins
For flash/nor/efm32 the EFM32GG12B Giant chip has been added to the
efm32_family along with its respective series and msc_rebase.
Testen on EFM32GG12B390F board
Change-Id: Idd7dfa93f26ac22566aed1be28f30db678cc0a25
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5567
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
As a consequence of a previous failed SWIM command any
subsequent attempts to enter SWIM mode fails. Change
stlink_usb_mode_enter to use stlink_usb_xfer_noerrcheck
instead.
Change-Id: I5c6a1a8e68d3dc77ec37264880383366fa6a75d9
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5547
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In order to extend the driver to support stlink-server over TCP,
we should always use a valid endpoint, as stlink-server is not permissive
and do not accept the invalid STLINK_NULL_EP.
STLINK_NULL_EP value was used for commands without an expected reply,
this value could be replaced with a valid endpoint without any impact
when the size is set to zero.
Change-Id: I003ad364e03d3a10bc036772db86310d996cbe81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5455
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Not all the jtag drivers have been migrated to the new reset model
and for those only we need to flush the jtag queue to make the
reset working with command 'adapter [de]assert ...'.
Add a queue flush and a FIXME comment to remove both when all the
drivers would be migrated.
Change-Id: Ib6667f987b1be2bce492841040302e742dd1cad1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5430
Tested-by: jenkins
While running OpenOCD on multi-target SoC, it's not immediate to
detect which target is associated to each GDB port. The log only
reports:
Info : Listening on port 3333 for gdb connections
and a verbose debug log is required to get such info.
Promote to LOG_INFO() the existing debug message that already
reports the association, obtaining for each port:
Info : starting gdb server for stm32mp15x.cpu0 on 3333
Info : Listening on port 3333 for gdb connections
Change-Id: I1bd75655a3449222c959e6e82f5e0f8f5acd908a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5525
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
It also get useful to handle the reset on some problematic chip,
as in http://openocd.zylin.com/5489
Replace the warning about deprecation with a more light debug
message.
Change-Id: I52de6359475ba31014ae77e596a87fe88b252177
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5514
Tested-by: jenkins
Reviewed-by: Edward Fewell <efewell@ti.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The tcl script src/target/startup.tcl has already the proper
centralized support to wait for all targets to halt after the
command "reset halt". The extra wait in cortex_a_deassert_reset()
is not required.
This extra wait is also an issue for multi-core support, because
waiting for one core to halt can delay the halt request to the
other cores.
Replace the indirect call to cortex_a_halt(), that embeds the wait
for halt, with a low-level halt sequence.
The on-going work on the reset framework is compatible with this
change; in fact it keeps in startup.tcl the wait for targets to
halt, even if current code proposal for cortex_a simply removes
the function cortex_a_deassert_reset().
Change-Id: Ic661c3791a29ba7d520e31f85a61f939a646feb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5472
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The usleep() function, and its associated useconds_t type
specifier, has been obsoleted by POSIX.1-2008.
OpenOCD has 28 call to usleep(), that should be migrated to the
replacement nanosleep(), but due to the different prototype
int nanosleep(const struct timespec *req, struct timespec *rem);
this can take some effort.
The type useconds_t is used in only one case, where it's used both
as parameter of usleep() and as value passed to LOG_DEBUG(). Due
to different implementation of useconds_t, there are cases that
trigger a compile warning in LOG_DEBUG() when useconds_t is more
than 32 bit.
E.g. with unistd.h in MinGW 4.x, useconds_t is defined as unsigned
long, thus being 32 or 64 bits depending on the target.
Replace the only instance of useconds_t.
Change-Id: I21724f8b06780abdb003a57222ff1d6840ff5419
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5544
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
In newlib, the argument of isalnum() and the similar functions in
ctype.h is checked to be either an int or an unsigned char.
Using a normal (signed) char triggers a compile time warning
warning: array subscript has type ‘char’ [-Wchar-subscripts]
Rewrite the function to separate the internal unsigned char
operations from the (signed) char parameter.
Change-Id: I5f19115f0b2de2b5b35dc07ef4b58a96161268ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Fixes: 5da746fa09 ("flash/nor/nrf5: detect newer devices without HWID table")
Reviewed-on: http://openocd.zylin.com/5545
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Return bool value in functions that return bool.
Change return type to bool to function is_gpio_valid().
Change-Id: Ic2e62be737772b22e69881c034956549f659370b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5552
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Events TARGET_EVENT_STEP_START and TARGET_EVENT_STEP_END
have been added - analogous to already existing events
TARGET_EVENT_RESUME_*.
This is an example of a concrete use case where having
these events is important:
In RISC-V processors without Debug Program Buffer, OpenOCD
cannot execute fence/fence.i when resuming or single-
stepping. With these events implemented, the user can
instead provide custom operations to achieve that same
effect prior to resuming the processor.
Change-Id: I786348ff08940759d99b0f24e9e0ed5a44581094
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5551
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
On stm32h747 writing/erasing bank 1 didn't work. It was because the
flash register base was always set for bank 0.
Tested on STM32H747I-DISCO board.
Change-Id: I7e8c43ecdda9dc70b114905f5ec6a6753ca29d82
Signed-off-by: Sasha Kozaruk <alkhozar@gmail.com>
Reviewed-on: http://openocd.zylin.com/5534
Reviewed-by: Christopher Head <chead@zaber.com>
Tested-by: jenkins
nSRST and sysreqreset are both broken for these targets. Upon a
hard reset, the target disables the TDO/TDI pins and the
ICEPick router will remove the target's TAP from the scan
chain. The scripts to do these tasks are run, but then
OpenOCD throws the reset again breaking the debug connection.
Until that issue can be resolved, vectreset is the only
reset that works without breaking the debug connection.
Update: original patch didn't have the correct reset command.
Change-Id: If7c985b703c87399a13364609d370d6222f4a66c
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5511
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While stlink v2 allows setting the jtag clock frequency till a max
of 18 MHz, the firmware seams unstable and not properly working.
Remove the entry for 18 MHz, at least until a fix get available.
Change-Id: I503e1b6a5709b5fbf1f1147fd3b5f34a0c5ee98c
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5465
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
when openocd fails to read armv8 register, the user is not informed
which register has caused the error.
for example, in AArch32 state ESR_EL3 read/write is not supported,
thus armv8_dpm_read_current_registers is always failing without mentioning
which register has caused the error.
Change-Id: I24c5abbda9fac24fb77a01777ed15261aeaaf800
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5516
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change the current message when a flash driver does not implement
the protect_check function to LOG_INFO() from LOG_WARNING(). The
user is still notified that the procedure isn't available, but
changes the tone to indicate this is expected with this flash
driver and not something that necessarily is a problem to fix.
Change-Id: If8a2e86a23c852d562346ca36734e5d02df4a851
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5539
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target types are sorted alphabetically
minor changes for some precision:
- cortex_a : it's an ARMv7-A core
- cortex_m : besides the ARMv7-M it support the v6-M and v8-M cores
Change-Id: I37ade2392fe3948fba4156a2831bbd8739fa9993
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5486
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add more argument check for "add-reg" command.
Changes since first revision:
-Removed arguments limitation(50 maximum) for "arc_set_reg_exists".
Changes:
25.03:
Removed inconsistency in "add-reg" function. Actually
"-type" option is optional and if it is not set,
register type is "int".
Change-Id: Ia21e6baf4fbda162f7811cd0fe305fc86ddafcfd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5523
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This adds the ATmega256RFR2 to the list of know devices for flashing.
Change-Id: Ib24a508762aaa84ba08ba37409db2ae674b46288
Signed-off-by: Lars Pöschel <poeschell+openocd@mailbox.org>
Reviewed-on: http://openocd.zylin.com/5504
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current method used for flash addressing uses 16 bit. Every access
to flash is 16 bit wide. With 16 address bits one can address 0x10000
unique locations á 16 bits thats 0x20000 bytes.
For flashes bigger than that avrs have an extended addressing with more
than 16 address bits. This is now implemented and used for flashs larger
than 0x20000 bytes.
Change-Id: Id8b6337dde3830fb3c56b9042872e040bb67c12d
Signed-off-by: Lars Pöschel <poeschell+openocd@mailbox.org>
Reviewed-on: http://openocd.zylin.com/5502
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commit fafe6dfc9c ("adapter: add command "adapter [de]assert
srst|trst [[de]assert srst|trst]"") was proposed in gerrit well
before commit a61ec3c1d7 ("adi_v5_dapdirect: add support for
adapter drivers that provide DAP API") get merged, so it didn't
include a complete support for dap direct.
The merge upstream of the two commits lacks the support by command
"adapter [de]assert" for dap direct
Let command command "adapter [de]assert" handle dap direct.
Change-Id: I1a69f8ee877c8fd57598ed4ad9d71da61d15457c
Fixes: commit fafe6dfc9c ("adapter: add command "adapter [de]assert srst|trst [[de]assert srst|trst]"")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5515
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While installing git on Windows, the user is prompted by a dialog
"Configuring the line ending conversions" to select the value for
the git property "core.autocrlf". The default choice proposed by
the installer is "Checkout Windows-style, commit Unix-style line
endings", that corresponds to "core.autocrlf=true".
Even if the dialog provides technical explanation of the different
choices, most users will blindly accept the default proposal.
With "core.autocrlf=true" git will convert to DOS mode all the
text files during "clone" (so can be edited by any crap Windows
tool) and convert back to UNIX mode during "push" operation.
While this is safe enough for C and TCL files, it breaks the
texinfo files.
The trailing '@' character used for command continuation in
https://www.gnu.org/software/texinfo/manual/texinfo/html_node/Def-Cmd-Continuation-Lines.html
does not accept being followed by CR+LF (DOS mode), generating a
build error. Same error can be replicated on Linux by passing the
file doc/openocd.texi through "unix2dos" command.
Tentative to fix this has already been proposed in
http://openocd.zylin.com/5294http://openocd.zylin.com/5413
by breaking the command continuation syntax, which is a no go.
The correct fix would require to force/suggest all the Windows
users to get rid of the crap DOS mode, but this could have side
effects.
To workaround the issue, add a .gitattributes file in the doc
folder, specifying a local conversion attribute for the files .txt
and .texi in the doc folder and overriding the eventual incorrect
global value of "core.autocrlf" selected during installation.
The local attribute "text eol=lf" is equivalent to the global one
"core.autocrlf=input".
Change-Id: I468a8f8125b6bc4628fce6c66eb082824ba3413f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5499
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
On CC32xx family of devices, sysrequest is disabled, and
vectreset is blocked by the boot loader (stops in a while(1)
statement). srst reset can leave the target in a state
that prevents debug.
This change enables using vectreset on SF variants by
moving the PC to the start of the user application in
internal flash. This allows for a more reliable reset,
but with two caveats:
1) This only works for the SF variant with internal
flash.
2) This only resets the CPU and not any peripherals.
Tested on CC3220SF rev B Launchpad in both SWD and
JTAG modes. Confirmed proper behavior of reset,
reset init, reset halt, and reset run commands.
Update: reworked per comment in code review. Re-tested
with CC3220SF Launchpad as both CC3220SF and as
CC32xx board to confirm reset behavior as expected.
Update: Added adapter srst delay 1100 line to the
CC3200 LaunchXL configuration file.
Change-Id: Ibc042d785c846c2223ae55b8f2410b75ed2df354
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5489
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The XDS110 supports alternate configurations, each of which has
a unique vid/pid:
0451/bef3 -- Standard (legacy) configuration
0451/bef4 -- Drag-n-Drop configuration
1cbe/02a5 -- CMSIS-DAP 2.0 on BULK interface configuration
It's not important to OpenOCD what the differences are except
that OpenOCD needs to know how to connect using the different
vid/pids and, in the case of the last one, use a different
interface for the debug connection.
Updated the XDS110 source to search for all possible
configurations, and updated the udev rules file to enable
user access to the alternate configuraitons.
For the curious, you can download the latest XDS emupack from
software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds_software_package_download.html
Install to an empty directory, and documentation for the
XDS110 is located in the .../ccs_base/common/uscif/xds110
of the installation.
Updated for comments in code review. Changed const variable
names to lower case. Reworked interface/endpoint setting
to use arrays suggestion.
Change-Id: Icc9d11c6618f43d87ae8171c78ebf238800d3ac2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5494
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Arrange all commands under a top level xds110 command. Fix
documentation to properly reflect the current functionality.
Also updated the links in the document to the new permanent
links for the XDS110 only support.
Patch updated for comments from code review. Return
ERROR_COMMAND_SYNTAX_ERROR for wrong number of args in
commands. Added deprecated commands to src/jtag/startup.tcl.
Change-Id: Ica45f65e1fdf7fa72866f4e28c4f6bce428d8ac9
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5495
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Confirmed that sysresetreq is supported and works better
for MSP432P4 and MSP432E4 targets than srst that was
previously being used.
Tested on MSP432P4111, MSP432P401R, and MSP432E401Y
Launchpads.
Change-Id: I1454c3379b9300bc133f82a766daeaefb98dbaac
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5488
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Starting with XDS110 firmware version 3.0.0.0, the peak TCK
frequency became 14,000 kHz. So the delay count calculation
in the current driver has been updated to use the new
formula for setting the TCK speed depending on which version
of the firmware is detected. And because of the changes, the
default TCK settings for the XDS110 based Launchpads can be
adjusted to take advantage of the higher TCK performance.
Note that the values used have been determined through
testing in the automated test labs to be the highest TCK
frequency with the XDS110 that are still reliable.
Different boards have a different peak TCK setting that
should be safe.
Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5493
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WB3x devices' flash are quite similar to STM32WB5x,
except the maximum flash size, which is 512K for WB3x and 1M for WB5x
Change-Id: I3098d7153a7429e0e72c75cec962c05768b0b018
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5475
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Old ST-LINK DFU returns an incorrect serial in the USB descriptor
example for the following serial "57FF72067265575742132067"
- the correct descriptor serial is:
0x32, 0x03, 0x35, 0x00, 0x37, 0x00, 0x46, 0x00, 0x46, 0x00 ...
this contains the length (0x32 = 50), the type (0x3 = DT_STRING)
and the serial in unicode format.
the serial part is: 0x0035, 0x0037, 0x0046, 0x0046 ... >> 57FF ...
this format could be read correctly by 'libusb_get_string_descriptor_ascii'
so this case is managed by libusb_helper::string_descriptor_equal
- the buggy DFU is not doing any unicode conversion and returns a raw
serial data in the descriptor:
0x1a, 0x03, 0x57, 0x00, 0xFF, 0x00, 0x72, 0x00 ...
>> 57 FF 72 ...
based on the length (0x1a = 26) we could easily decide if we have to fixup the serial
and then we have just to convert the raw data into printable characters using sprintf
example for an old ST-LINK/V2 standalone:
before : 'W?rreWWB g'
after : '57FF72067265575742132067'
=> same as the displayed value in STM32CubeProgrammer
tested using these commands
using the buggy serial
-c "hla_serial \x57\x3f\x72\x06\x72\x65\x57\x57\x42\x13\x20\x67"
using the computed serial
-c "hla_serial 57FF72067265575742132067"
Change-Id: I1213818257663eeb8e76f419087d3127d0524842
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5396
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduce a callback function that could be passed to jtag_libusb_open
to permit adapters to compute their custom/exotic serials.
the callback should return a non NULL value only when the serial could not
be retrieved by the standard 'libusb_get_string_descriptor_ascii'
Change-Id: Ib95d6bdfc4ee655eda538fba8becfa183c3b0059
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5496
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
+ minor changes in comments' alignment to please our eyes
Change-Id: Ifa35a1032afc4e9aee524f596c0298a9eea49c37
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5500
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
The memory leak can be reproduced by using an arbitrary RTOS
and valgrind:
$ valgrind --leak-check=full --show-leak-kinds=all
[...]
==9656== 224 (80 direct, 144 indirect) bytes in 1 blocks are definitely lost in loss record 3 of 3
==9656== at 0x483CD99: calloc (in /usr/lib/x86_64-linux-gnu/valgrind/vgpreload_memcheck-amd64-linux.so)
==9656== by 0x1C541A: os_alloc (rtos.c:79)
==9656== by 0x1C569E: os_alloc_create (rtos.c:111)
==9656== by 0x1C569E: rtos_create (rtos.c:153)
==9656== by 0x1AE332: target_configure (target.c:4899)
==9656== by 0x1AF228: jim_target_configure (target.c:4952)
==9656== by 0x1C9EF9: command_unknown (command.c:1066)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313FB6: Jim_EvalObj (jim.c:10814)
==9656== by 0x3154A3: Jim_EvalFile (jim.c:11207)
==9656== by 0x316015: Jim_SourceCoreCommand (jim.c:15230)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313B8B: JimEvalObjList (jim.c:10605)
[...]
Change-Id: I2cd41a154fb8570842601ff4e3e76502f5908f49
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5479
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32G0 and G4 uses the same flash driver as the stm32l4x
Change-Id: Ic1c4be70aaee809536912e0390f07893efb9a082
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5482
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The RZ/A1 is not part of the R-Car family, but is rather an RZ family.
Fix the naming.
Change-Id: I5f882b2467e87e534e0f1c827554e664a7d55664
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5445
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
TCK during nSRST assert/deassert code.
To support LPRF targets (CC13xx/CC26xx), TCK must be toggled
for 50 ms while nSRST is asserted and right after it is
released. This allows the core to halt in boot ROM before
code is run that might interfere with debug access.
The current routine has two issues. It shouldn't be run at
all if the target is using SWD. And the delay needs to
be a real-time 50 ms, so the number of TCK periods should
be calculated off the set speed.
Change-Id: If993031b84cf2a505ea67a6633602c4b01cd8e1e
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Hypervisor mode is present only if the optional virtualization
extensions are available. Moreover, virtualization extensions
require that also security extensions are implemented.
Add the required infrastructure for the shadowed registers in
hypervisor mode.
Make monitor shadowed registers visible in hypervisor mode too.
Make hypervisor shadowed registers visible in hypervisor mode
only.
Check during cortex_a examine if virtualization extensions are
present and then conditionally enable the visibility of both
hypervisor and monitor modes shadowed registers.
Change-Id: I81dbb1ee8baf4c9f1a2226b77c10c8a2a7b34871
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5261
Tested-by: jenkins
Accordingly to ARM DDI 0406C at B1.5, the security extensions for
armv7a are optional extensions and can be detected by reading
ID_PFR1.
The monitor mode is part of the security extensions and the shadow
registers "sp_mon", "lr_mon" and "spsr_mon" are only present with
the security extensions.
Read the register ID_PFR1 during cortex_a examine, determine if
security extension is present and then conditionally enable the
visibility of the monitor mode shadow registers.
Change-Id: Ib4834698659046566f6dc5cd35b44de122dc02e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5259
Tested-by: jenkins
The fields core_type and core_mode use the same enum arm_mode
but encode different information, making the code less immediate
to read.
Use a different enum arm_core_type for the field core_type.
The code behavior is not changed.
Change-Id: I60f2095ea6801dfe22f6da81ec295ca71ef90466
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5258
Tested-by: jenkins
Commit 2efb1f14f6 ("Add GDB remote target description support
for ARM4") inserts two additional registers "sp" and "lr" in the
table arm_core_regs[], thus shifting by two the position of the
last three registers already present
"sp_mon" moved from index 37 to 39
"lr_mon" moved from index 38 to 40
"spsr_mon" moved from index 39 to 41
Part of the code is updated (e.g. enum defining ARM_SPSR_MON and
array arm_mon_indices[]), but it's missing the update of mapping
in armv4_5_core_reg_map[].
Fix armv4_5_core_reg_map[].
Change-Id: I0bdf766183392eb738206b876cd9559aacc29fa0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 2efb1f14f6 ("Add GDB remote target description support for ARM4")
Reviewed-on: http://openocd.zylin.com/5257
Tested-by: jenkins
The function ftdi_set_signal() does not propagate the pin change
until next call to mpsse_flush(). Current code does not toggles
immediately the reset pins if polling is turned off.
Call mpsse_flush() at the end of ftdi_reset().
While there, remove the duplicated LOG message.
Change-Id: I79eacfe4fc32b5cdf2dc1b78f3660d96988466bc
Fixes: 8850eb8f2c ("swd: get rid of jtag queue to assert/deassert srst")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5431
Tested-by: jenkins
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
OpenOCD is stuck at jimtcl tag 0.77 that is 3 years old.
The latest tag 0.79 (2019-11-20) is already used by debian build,
which packs jim library separately, as shown in [1]. Today only
the build for architecture powerpcspe is still not updated to
latest package version.
I have been using jim 0.79 since the day of the release, without
any issue.
Switch jimtcl to latest tag 0.79
[1] https://packages.debian.org/sid/openocd
Change-Id: I3426e68c32f88ecde74d4278303925423db451e0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The jimtcl commit 41c5ff1809f5 ("jim.c: Fix Object leak in zlib
support") https://repo.or.cz/jimtcl.git/commit/41c5ff1809f5
makes Jim_SetResultFormatted() freeing the parameters that have
zero refcount.
OpenOCD commit 559d08c19e ("jim tests: use installed") adds the
only code instance in OpenOCD that first passes a zero refcount
object to Jim_SetResultFormatted() and then frees it.
By switching jimtcl version to 0.78 or newer this causes a crash
of OpenOCD.
To trigger the crash in a telnet session, check that the current
target is running and type:
[target current] arp_waitstate halted 1
Remove the call to Jim_FreeNewObj() after the call to
Jim_SetResultFormatted().
Change-Id: I5f5a8bca96a0e8466ff7b789fe578ea9785fa550
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5453
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The jtag API reset() is synchronous, but this was not highlighted
in the description.
Change-Id: I76ffb7eec97c8608cfbef0b9268ee18a5f50b221
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8850eb8f2c ("swd: get rid of jtag queue to assert/deassert srst")
Reviewed-on: http://openocd.zylin.com/5471
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
A common problem with target configurations appears to be broken
debug base address configuration. ARM DDI0406C.d specifies in App. D,
1.4.1, that bit 31 of the debug base address serves as identification
of an external debugger, as opposed to an internal access to memory
mapped debug registers by the CPU. External accesses are treated
as privileged and require no debug authentification via the lock
access register.
Sometimes the base address of a debug component is wrong even
in the targets' ROM table. In this case, the correct base address
must be specified using the -dbgbase argument when creating the
target.
This patch adds a warning when bit 31 of the debug base address
is not set, as a hint to the user.
Change-Id: I9c41d85a138123c657ef655e3436a2aa39249dcc
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/5105
Tested-by: jenkins
Reviewed-by: Tommy Vestermark <tov@vestermark.dk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As stated in ARM v8-A Architecture Reference Manual (ARM DDI 0487E.a)
in Chapter H4.3 DCC and ITR access modes:
Writes to EDITR trigger the instruction to be executed if the PE
is in Debug state:
- If the PE is in AArch64 state, this is an A64 instruction.
- If the PE is in AArch32 state, this is a T32 instruction
But in armv8_opcodes specifically in t32_opcodes we were using some
A32 instructions for HLT, LDRx and STRx opcodes.
Using the correct LDRx and STRx opcodes, fixes 16 and 8 bits memory access
when the PE is in AArch32 state.
Change-Id: Ib1acbdd4966297e7b069569bcb8deea3c3993615
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5346
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Before this patch aarch64_set_breakpoint was using either A64, or A32
HLT opcode by relying on armv8_opcode helper.
This behaviors ignores the fact that in AArch32 state the core could
execute Thumb-2 instructions, and gdb could request to insert a soft
bkpt in a Thumb-2 code chunk.
In this change, we check the core_state and bkpt length to know the
correct opcode to use.
Note: based on https://sourceware.org/gdb/current/onlinedocs/gdb/ARM-Breakpoint-Kinds.html
if bkpt length/kind == 3, we should replace a 32-bit Thumb-2 opcode,
then we use twice the 16 bits Thumb-2 bkpt opcode and we fix-up the
length to 4 bytes, in order to set correctly the bpkt.
Change-Id: I8f3551124412c61d155eae87761767e9937f917d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5355
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
when using step command from gdb the step happens without any issue,
but aarch64_step call explicitly aarch64_poll which consumes the
status change to HALTED, so it does not inform gdb that the step has
finished.
by removing this call, all is back to normal and openocd could inform gdb
that the step has finished.
Change-Id: I9366aecd20f7d52259b050b8653189b67d9299d0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5354
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the same semihosting handlers chain is declared twice:
1. in src/target/armv4_5.c
2. in src/target/riscv/riscv.c
to make it simpler we moved the declaration into
'src/target/semihosting_common.c' under semihosting_common_handlers[].
then we used this into both of armv4_5.c and riscv.c
Change-Id: If813b3fd5eb2476658f1308f741c4e805141f617
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5473
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Both Gen2 and Gen3 used the same init_reset{} implementation,
pull it into common file and include it from both generations.
Moreover, this behavior is SoC specific, not board specific,
so move the common init_reset into target/ directory.
Change-Id: I5489a4bff9a786da8cb7fd7a515b0c9ce9dc16e3
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5400
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Added fixes for issues found in additional code reviews.
Fixed host Endianness issues with using buffer reads
and writes instead of the *_u32 variants.
Changed code that tried to ID banks by hardcode
bank_number values to use instead the bank base
address. This fixes problems using configurations
with multiple devices.
Note that this replaces Change 4786 which has
been abandoned because of extensive changes to
the code to stop IDing banks by name. And I
think I really messed up a rebase/merge on the
document file.
Tested on MSP432P401R, MSP432P4111, and MSP432E401Y
Launchpads.
Change-Id: Id05798b3aa78ae5cbe725ee762a164d673ee5767
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
Writing bits to an uninitialized buffer generated false warnings.
Zero buffers before setting them by buf_set_u32|64()
(do it only if bit-by-bit copy loop is used,
zeroed buffer is not necessary if a fast path write is used)
Change-Id: I2f7f8ddb45b0cbd08d3e249534fc51f4b5cc6694
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5383
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The aligning code generated a clang static analyzer warning and
imposed huge memory leak. This part of code was removed and
flash infrastructure to alignment is used instead.
Not tested on hw!
Change-Id: I7c71da87547e71d595a7e7071ae5adcc1cecc827
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5367
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The name 'common' does not make sense anymore. While at it,
remove some unnecessary #includes.
Change-Id: If9798a5cce179438d89428a598d8ca05c8e5f20c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5434
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Drop old Renesas Gen2 SoC configurations, as they were superseded by
the new unified config.
Change-Id: I7c2ccbdc13b01a552ce9cafdc1538f226beaa9f2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5399
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Supporting two libusb versions provides additional development challenges
without additional advantage. In most cases we need to patch libusb0_common and
libusb1_common without real ability to test libusb0_common.
Change-Id: Icbb19c6809b14533fe2acf7a877377b3be4cbd61
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/5432
Tested-by: jenkins
Switch Renesas R-Car Gen2 boards which are currently supported from
the old ad-hoc SoC configuration to the new unified configuration.
Change-Id: I8a67bceb3ae92d840ae4dbac20868c75e83f7d58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5398
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add configuration for the Renesas R-Car Generation 2 targets.
These are SoCs with Cortex A15s and A7s. All cores currently
supported by OpenOCD are supported here as well as two new
cores, M2N and V2H, for the sake of support completeness.
Change-Id: Ib6fe70a91360b4f8bd69822ee28b6dea530cfa0a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5397
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this new device has the following features:
- single core cortex-M7
- 2MB flash - dual bank
- page size 8k
- write protection grouped by 4 sectors
- write block size 128 bits (16 bytes)
the bit definition of FLASH_CR is different than STM32H74x,
that's why we introduced a helper to compute the FLASH_CR value
Change-Id: I4da10cde8dd215b1b0f2645f0efdba9d198038d1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5441
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch is an initial bump of ARC-specific code
which implements the ARCv2 target(EMSK board) initializing
routine and some basic remote connection/load/continue
functionality.
Changes:
03.12.2019:
-Add return value checks.
-Using static code analizer next fixes were made:
Mem leak in functions:
arc_jtag_read_memory,arc_jtag_read_memory,
arc_jtag_write_registers, arc_jtag_read_registers,
jim_arc_add_reg_type_flags, jim_arc_add_reg_type_struct,
arc_build_reg_cache, arc_mem_read.
Dead code in "arc_mem_read";
In arc_save_context, arc_restore_context correct arguments
in"memset" calls.
In "build_bcr_reg_cache", "arc_build_reg_cache" check
if list is not empty.
29.12.2019
-Moved code from arc_v2.c to arc.c
-Added checks of the result of calloc/malloc calls
-Reworked arc_cmd.c: replaced spagetty code with functions
-Moved to one style in if statements - to "if(!bla)"
-Changed Licence headers
22.01.2020
-Removed unused variables in arc_common
-Renamed register operation functions
-Introduced arc_deinit_target function
-Fixed interrupt handling in halt/resume:
* add irq_state field in arc_common
* fix irq enable/disable calls ( now STATUS32 register is used)
-Switched from buf_set(get)_us32() usage to target_buffer_set(get)_u32()
-Made some cleanup
30.01.2020
-Removed redundant arc_register struct, moved target link to arc_reg_desc
-Introduced link to BCR reg cache in arc_common for freeing memory.
-Now arc_deinit_target frees all arc-related allocated memory.
Valgrind shows no memory leaks.
-Inroduced arch description in arc.c
01.02.2020
-Remove small memory allocations in arc_init_reg. Instead created reg_value
and feature fields in arc_reg_desc.
-Add return value for arc_init_reg() func.
-Replaced some integer constants(61,62,63) with defines.
-Removed redundant conversions in arc_reg_get_field().
-Moved iccm/dccm configuration code from arc_configure()
to separate functions.
19.02.2020
-Change sizeof(struct) to sizeof(*ptr) in allocations
-Changed if/while(ptr != NULL) to if/while(ptr)
-Removed unused variables from struct arc_jtag
-Add additional structs to arc_reg_data_type
to reduce amount of memory allocations calls
and simplifying memory freeing.
-Add helper arc_reg_bitfield_t struct which includes
reg_data_type_bitfield object and char[] name. Reduces
memory allocations calls.
-Add limit for reg_type/reg_type_field names(20 symbols).
-Add in jim_arc_add_reg_type*() functions additional
argnument checks(amount of field/name size).
-In jim_arc_add_reg_type*() reduced amount of memory allocations.
-Cleanup of jim_arc_add_reg_type*() functions.
-For commands update ".usage" fields according docopt.
-Cleanup in arc_jtag.c
-Renamed functions which require jtag_exeutre_queue() to arc_jtag_enque_*()
-Add arc_jtag_enque_register_rw() function, which r/w to jtag ir/dr regs
during regiter r/w.
24.02:
-Change include guards in arc* files according coding style
-Remove _t suffix in struct arc_reg_bitfield_t
-Some cleanup
Change-Id: I6ab0e82b12e6ddb683c9d13dfb7dd6f49a30cb9f
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5332
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Empty lines at end of text files are useless.
Remove them.
Change-Id: I30e4d3d03c4ce846aa7bcefa7366f88732275557
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5170
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Id05a7bd944edccaa03ed9eb48599b2e262664cf0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5169
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Iea4c8425e137d6252fb2e5b62e0b124c73a01cb6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5168
Tested-by: jenkins
Some text file is missing newline at EOF.
Add it.
Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
The default log output is stderr. After the command "log_output"
has been used to set an output log file, it is possible to return
back to stderr only on *NIX hosts specifying a new log output file
as "/dev/stderr", but this is not intuitive, not documented and
not portable out of *NIX.
Make command "log_output" able to set back the default output to
stderr when the parameter is either "default" or is missing.
While there, add debug message to log the change and make the
command return error on incorrect syntax.
Change-Id: I8c7c929780f58e2c23936737c8e7274a96734786
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5233
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Deassert the reset only if connect under reset is not required;
otherwise, assert the reset.
This fix aligns the behavior of connect under reset in dapdirect
with the behavior in jtag and swd.
Change-Id: I937ef4320b44e51ef6cb0e349e12348dbfbe4abb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5415
Tested-by: jenkins
The configure.ac file restricted this to only 'arm' CPUs, but
${host_cpu} is 'aarch64' (not 'arm') for 64 bit ARM CPUs.
Tested on a Raspberry Pi compute module 3.
Change-Id: I6cb1d7e7fadc51dbb12419176f1faf0a0cb0b228
Signed-off-by: Mara Bos <m-ou.se@m-ou.se>
Reviewed-on: http://openocd.zylin.com/5274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Board includes an internal adapter (interface/ftdi/imx8mp-evk.cfg) and a
standard external ARM-10 connector.
Change-Id: Ibb301011665b1edfb95be1213d8100143f6839dd
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The imx8mp-evk board has a FT4232H chip connected to the chip's JTAG
pins.
Switching between this on-board interface and the external ARM-10
connector is controlled by an GPIO which is behind an i2c expander
connected to the same FTDI chip.
Switching can be performed using the NXP bcu tool:
https://github.com/NXPmicro/bcu
Change-Id: Ic910515f76eaf09ea6d0f755b026fb09cf09ccfc
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5426
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Report the 32-byte alignemnt requirement via the bank structure rather
than enforcing it ad-hoc in the write routine. This allows people to do
non-32-byte-aligned writes if they want, with the infrastructure fixing
up the addresses passed to the low-level driver.
Change-Id: I2c4f532f2000435954a900224dbc9f2c30d1cc94
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5388
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this, a failed attempt to change option bytes will silently
appear to succeed but without actually changing the option bytes
(confusingly, the option bytes will still read back as if they had been
changed until a reboot as well!).
Change-Id: Id529c6c384a8a16be75f5702310670d99d8fac79
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5418
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reuse the existing tracing functionality of HLA mode to support
tracing in DAP direct mode.
Change-Id: I75a01e88ba5d3e45717e4108b99697ac3225db9e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5409
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit 3799eded67 ("target/aarch64: add support for
multi-architecture gdb") passes the constant string "aarch64" as
architecture to gdb. This is not working if the core is running
in 32 bits mode; gdb reports:
Truncated register 8 in remote 'g' packet
then closes the connection with OpenOCD.
Make the architecture string dependant from the current state of
the core.
Change-Id: I16e1614ea02ba29bf87f450b3dfe25c83c9a3612
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5234
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
We have the macro ARRAY_SIZE() already available. Use it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ARRAY_SIZE -f {} \;
Change-Id: Ic7da9b710edf118eacb08f9e222f34208c580842
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5198
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types UNNECESSARY_PARENTHESES -f {} \;
then fixed manually.
Change-Id: Ia2d9a0953d9b89fc87dc1195aa05c7f63c068c48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5196
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro NDS32_COMMON_MAGIC was cast-ed to int to avoid compile
time error for comparison type mismatch while comparing it with
the field common_magic.
This is incorrect because the macro value is a 32 bit unsigned
value; better changing the type of the field common_magic to keep
the unsigned value.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPECAST_INT_CONSTANT -f {} \;
Change-Id: Ib5924b6cecdffe70ab5c78d3b30a9c8e4deb7c7b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5193
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command CMD_STOP_SIMU had been defined in jtag_vpi for a long time
(since the beginning?) but has not been utilized until now.
Its purpose is to signal to the jtag_vpi server (i.e. the RTL
simulation software) that the simulation shall be stopped.
This commit adds a TCL configuration command that selects whether
CMD_STOP_SIMU will be sent to the jtag_vpi server when OpenOCD is
about to exit. This functionality is off by default to maintain
identical behavior as in previous OpenOCD versions, unless the user
enables it explicitly.
Change-Id: If3894af6efa61038ccf6c9191f664e2128f2ef11
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5407
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When $ADDRESS == $BASE that address used to be excluded.
After this commit $ADDRESS == $BASE is within the range.
Now the rule for "iswithin" is:
$BASE <= $ADDRESS < ($BASE + $LEN)
Thanks to Antonio Borneo <borneo.antonio@gmail.com> for noticing this.
Change-Id: I74373c6010e069372d886fa7ecd8120892616834
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4799
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this is to avoid confusion with STM32 L4, L4+ and L5 families
also:
- a warning message is changed to error
- stm32l0x and stm32l1x aliases has been created to permit
the usage of either names
Change-Id: If3f16d2a3b7d1369959aa7407da37a9076ea91d7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5437
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This will enable us to use either name when calling flash driver commands.
For example the stm32wbx family use the same flash driver as the stm32l4x, so
the user has to use 'stm32l4x lock 0' which can be confusing.
Now the user can also use 'stm32wbx lock 0' with the same result.
Change-Id: Ic0d8da9afc202d7cc82d9b9949827e958a1cc824
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5436
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace "Instruction Register (DR)" with "Instruction Register (IR)",
that is sed "s@DR@IR@", which was likely a copy-paste error.
Change-Id: I3e625872c855d655485b3efa5f50fe1c00ecbf52
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5446
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While ST internal documentation for STLINK-V3 reports that 8 bits
read/write commands handle 512 bytes of data, a firmware bug makes
it crashing on high data size.
This is fixed with firmware V3J6 (shipped together with V2J36).
Check for firmware version to use the proper data size.
Change-Id: Iaba6cd26bbe130097c1c19de610680e0e8b69bfc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/259/
Reviewed-on: http://openocd.zylin.com/5408
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the TLR sequence is sent as result of the command "adapter
assert trst" while polling is off, the TLR sequence is not sent out
until a following jtag operation.
Flush the jtag queue before return.
Change-Id: I20efd7137cb7b1d1c4f73c1362cbe4e57aeaae49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
repo.or.cz already redirects HTTP requests to HTTPS. There is therefore
no possible benefit to keeping the submodule URLs using HTTP—anyone who
can’t access via HTTPS will fail anyway, immediately after the redirect.
Changing the submodule URLs eliminates one unnecessary HTTP request and,
more importantly, eliminates SSLStrip-style attacks.
Change-Id: I9faf1ec8aa87bcfd1acafe2c445a0baf2abfbd09
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5406
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Add driver for the RPC block in HF mode on Renesas R-Car Gen3 SoCs.
This driver allows operating the on-SIP HF memory.
Note that HF is CFI compliant flash, but it is not memory mapped,
hence the need to replace all the memory accessors and read/write
functions. The write function is entirely replaced to increase
performance and is Spansion/AMD specific, since there is no known
SIP with other HF from another vendor.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen3 SoC using HyperFlash:
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME rpchf 0x08000000 0x4000000 2 2 $_CHIPNAME.a57.0
Change-Id: Ie18729d017eeb46e1363333ffe002d010dfc5ead
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5149
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The fallback provided for the jtag_reset command always fails with a
strange message: 'Error: invalid command name "de"'
This is caused by incorrect quoting inside the warning message.
Fixes: c07b774e8f ("jtag: replace command "jtag_reset" with "adapter [de]assert"")
Change-Id: Icd47fca2b5a7b33474bfb0040e88193a0968f301
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
currently we have different types of same command group:
- starting with adapter_*
- starting with interface*
- without adapter or interface prefix.
Since interface name is already used, we can only use "adapter" command
group by keeping old commands as well.
Change-Id: Id0a1cb63a2ea6860c67ae1e7a3a06a37ddf464f4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4774
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fix comment of tested errors in asm src.
List all relevant errors in FLASH_ERROR mask: FLASH_PROGERR was missing
and any trial to re-program already programmed double word ended up
in the error bit held uncleared and flash write permanetly repeating
the error message until reset.
Lock the bank also after unsuccesfull write_block run.
Set async target algo block size to size of double word.
Remove warning in case of write_block success. In case of error
use LOG_ERROR instead of warning.
Change-Id: Ibf6d5e306a4c2eaa43de67d636b4902c737f02f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5360
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The original code paded the write chunk with random bytes by overrunning
the buffer. An user can easily regard the random bytes to
be a programming error.
Change-Id: Ib0f47b5bc406bc6a7c32f3d929bf324a17c7c1e1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5359
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Since commit 7f260f5009 native OpenOCD
command handlers should not directly use Jim_SetResult functions.
The Tcl result of a native command is built as concatenation of
command_print() strings and Jim_SetResult() is called after return
of the command handler.
Replace "wrong number of args" error messages (now not delivered to user)
by simply return ERROR_COMMAND_SYNTAX_ERROR
Change-Id: I40c1374a13859cefbdef68e0f1c13ab93538bd50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5363
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The chip->hwid is uint32_t , fix the print format.
This was detected by TravisCI on OSX, where this triggers a build error.
Change-Id: I776a7bb50e396c8fccc24500dec4750190da7982
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5401
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ilya Kharin <akscram@gmail.com>
Commit [1] was submitted in gerrit well before the conflicting
commit [2] get merged in master branch. While it was fine
committing in master branch [1] alone, it should not be
committed "as is" after [2].
Unfortunately gerrit did not complained committing [1] after [2].
The result is that master branch does not build anymore when the
driver xlnx-pcie-xvc is enabled at configure time by the optional
flag --enable-xlnx-pcie-xvc.
Apply to the driver the required changes as in [2].
While there, remove the duplicated struct xlnx_pcie_xvc_transports
and the struct field already implicitly initialized to zero.
[1] ff6d0704ec ("jtag: drivers: xlnx-pcie-xvc: Add support for
Xilinx XVC/PCIe")
[2] efd1d64222 ("adapter: switch from struct jtag_interface to
adapter_driver")
Change-Id: I5498479b802a231afbee1b845ae9775e1da7c728
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5402
Reviewed-by: Moritz Fischer <moritzf@google.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add driver for the SH QSPI controller. This SPI controller is often
connected to the boot SPI NOR flash on R-Car Gen2 platforms.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen2 SoC and make SRAM work area available:
flash bank flash0 sh_qspi 0xe6b10000 0 0 0 ${_TARGETNAME}0 cs0
${_TARGETNAME}0 configure -work-area-phys 0xe6300000 -work-area-virt 0xe6300000 -work-area-size 0x10000 -work-area-backup 0
To install mainline U-Boot on the board, use the following procedure:
proc update_uboot {} {
# SPL
flash erase_sector 0 0x0 0x0
flash write_bank 0 /u-boot/spl/u-boot-spl.bin 0x0
# U-Boot
flash erase_sector 0 0x5 0x6
flash write_bank 0 /u-boot/u-boot.img 0x140000
}
Change-Id: Ief22f61e93bcabae37f6e371156dece6c4be3459
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
V2: - Add Makefile and linker script for the SH QSPI IO algorithm
- Include the algorithm code instead of hard-coding it
Reviewed-on: http://openocd.zylin.com/5143
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A USB bulk write/read operation may fail with different errors:
LIBUSB_ERROR_TIMEOUT if the transfer timed out (and populates transferred)
LIBUSB_ERROR_PIPE if the endpoint halted
LIBUSB_ERROR_OVERFLOW if the device offered more data, see Packets and overflows
LIBUSB_ERROR_NO_DEVICE if the device has been disconnected
another LIBUSB_ERROR code on other failures
Current OpenOCD code is using the transfer size based error detection.
Which may not always work. For example for LIBUSB_ERROR_OVERFLOW as libusb
documentation says:
"Problems may occur if the device attempts to send more data than can fit in
the buffer. libusb reports LIBUSB_TRANSFER_OVERFLOW for this condition but
other behaviour is largely undefined: actual_length may or may not be accurate,
the chunk of data that can fit in the buffer (before overflow) may or may not
have been transferred."
This patch is refactoring code to use actual error return value for
error detection instead of size.
Change-Id: Iec0798438ca7b5c76e2e2912af21d9aa76ee0217
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4590
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.
Access to the JTAG registers happens via the PCI Express extended
configuration space.
This can be used to debug soft-cores instantiated in the FPGA fabric.
The clang static checker doesn't find any new problems with this change.
Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: I6a810d2a54edcd13ad9a87d24a7334802c41623b
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5391
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: Ib967520f027b03eb1792b36ede52335df8e23941
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5390
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add possibility to supply custom CFI memory accessors via cfi_info
and override the default memory-mapped ones.
Change-Id: I1b6bc1db69fc33e8cdef96c41742c40e6d8917e9
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The size argument is always set to bank->bus_width and bank pointer
is now passed into cfi_target_{read,write}_memory(), so the size
can be accessed through the bank pointer inside the function instead
of being explicitly passed in.
Change-Id: I0abc1cc3bf513281c10cb5de7a21cb0e75cb7676
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5389
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace passing in struct target with passing in struct flash_bank,
so that the later can contain function pointers to custom per-driver
memory accessor functions.
Change-Id: Id2573a6d5f1a73ed9c4f73c53592a9a335a11c99
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5146
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fixed only 2 error returns discovered by clang static analyzer.
There are obviously many more missing error tests in avr32_jtag.c
These was not fixed to keep this change minimal.
Not tested with hw.
Change-Id: I6c79f6248db774990ddb42c0dacdb621651ed69e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5378
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Discoverd by clang static analyzer.
While on it remove useless type casts from arm946e_read_cp15() parameter.
Change-Id: I549e19685b431400243800ee0f7d1bbe6cdb14b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5376
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
STM32L4P/Q devices have:
- similar flash layout as STM32L4R/S devices
- 1024K of flash memory (some parts have 512K only)
tested on NUCLEO-L4P5ZG using board/st_nucleo_l4.cfg
Change-Id: I77047351bc7dcd7c76d0f31a77be73005104a06f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This rework is inspired from the 'flash/nor/stm32h7x.c'
This rework will ease the support of new devices on top of this driver:
for example: STM32WB have different flash base and size addresses
Notes:
- stm32l4_probe modified in order to charge the correct part_info from
the defined stm32l4_parts according to the device id
- stm32l4_flash_bank.bank2_start is replaced by .part_info->bank1_sectors
- STM32_FLASH_BASE is removed , part_info->flash_regs_base will be used instead
based on that flash register addresses are changed to offsets,
>> stm32l4_get_flash_reg was modified accordingly
- stm32l4_read_option and stm32l4_write_option was modified to accept an
offset instead of an absolute address, luckily this is the commands'
argument by default
- stm32l4_mass_erase modifications :
- use MER2 only on top of dual bank devices
- wait for BUSY bit before starting the mass erase
Change-Id: Ib35bfc3cbadc76bbeaaaba9005b82077b9e1e744
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4932
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
The `value` variable is passed into `target_fill_mem` as its
second-to-last parameter. That parameter is of type `uint64_t`. It is
appropriate to parse the value as that type, since otherwise a target
with a 32-bit address space but 64-bit data write capabilities would not
be able to exercise those capabilities.
Change-Id: Ib336d47d42c27cd2b5ba1206b04e8f740f167dba
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5219
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Arm DPv1 and DPv2 support banked registers by setting the bank in
field DPBANKSEL of register DP_SELECT.
Old ST-Link firmware don't support banked registers and setting a
bank other than bank zero on DPv1 or DPv2 cause issues in the
firmware because it cannot set back bank zero to read CTRL/STAT.
New ST-Link firmware mask away DPBANKSEL bits while writing in
DP_SELECT but support banked register using the same packed method
used by OpenOCD:
#define BANK_REG(bank, reg) (((bank) << 4) | (reg))
Add a new macro STLINK_F_HAS_DPBANKSEL for firmware that support
arm DPv1 and DPv2, plus trigger an error if banked registers are
requested on old firmware.
Prevent changing DPBANKSEL on old firmware.
Log a debug message when changing DPBANKSEL will be ignored.
Change-Id: Iaa592517831d63f8da2290db54f6b32504e3081b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4978
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some high level adapters, like STLINK-V3 and new firmware for
ST-Link/V2, provide API to directly access the DAP registers
hiding the details of the physical transport JTAG or SWD.
OpenOCD has already the intermediate API in struct dap_ops that
are suitable for such adapters, but are not exposed to the
adapter drivers.
Add in struct adapter_driver two independent struct dap_ops for
the cases of physical JTAG and SWD transport.
Add new transport names "dapdirect_jtag" and "dapdirect_swd", to
be used by the drivers that provide one or both DAP API.
Add the necessarily glue in target/adi_v5_dapdirect.c
Change-Id: I2bb8e3a80fba750f2c218d877cfa5888428e3c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SWD is already implemented, so remove the item.
Rename the section JTAG as Adapter, including the subsections.
Add an initial list of pending activities after the restructure
of the JTAG layer.
Change-Id: I540777344c62a746df8347538fe8b29e4d72e1c7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4901
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To reorganize the adapters code, introduce an adapter_driver
struct that contains all the adapter generic part, while
keeping in two separate struct the specific API jtag_ops and
swd_ops.
Move the allocation of *adapter_driver from the JTAG-specific
file core.c to the more adapter-specific file adapter.c
While splitting the old jtag_interface for every driver, put
the fields in the same order as in the struct declaration so
we keep a consistent code across all the drivers.
While other transport specific API could/would be added as
separate ops, nothing is done here for HLA.
Change-Id: I2d60f97ac514c0dd2d93a6ec9be66fd9d388dad5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4900
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
kitprog is SWD only and we do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.
Change-Id: Ic586278368301eb669bc6e4e641f683a81cb171d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4899
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.
Change-Id: I6c87d9ffebaa383c998cf273188b3e7f28b3fe95
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4898
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
After the cleanup of swd and hla, there should be no more calls
to jtag_execute_queue() or to queue jtag commands if current
transport is not jtag. Thus we can start removing the jtag
specific code from adapters that do not support jtag.
To prevent some remaining call to jtag_execute_queue() to crash
openocd, verify the transport, print an error message if the
transport is not jtag, call the adapter's jtag_execute_queue()
only if it exist.
To identify code that still add commands in the jtag queue even
if transport is not jtag, print an error message in the function
jtag_queue_command(). For the moment, still queue the message,
even if will cause a memory leak if there is no following call
to jtag_execute_queue(); the target is to identify the issue and
cleanup the code, thus solving also the leak.
Change-Id: I8fc85f754aa057aad1df05ff0448c8619897da23
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4897
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HLA uses its own internal driver's API to control the adapter's
system reset, but at the same time it calls jtag_add_reset() to
avoid breaking the internal logic of OpenOCD. This implicitly
forces HLA to rely on jtag queue mechanism, even if HLA has no
link with JTAG state machine. It requires HLA to implement an
empty execute_queue() to comply with the JTAG queue.
Modify the HLA framework and the HLA targets to use the new
adapter API for system_reset and decouple HLA from JTAG queue.
Rename the HLA static functions adapter_assert_reset() and
adapter_deassert_reset() to avoid overlap with the global
functions with same name.
While there, fix a minor typo in a comment s/incase/in case/.
Do not remove from HLA the JTAG specific API execute_queue(),
even if not required anymore, because OpenOCD code still has
calls to jtag_execute_queue() in case of non JTAG transport.
Change-Id: I0e65e3e557bd665bd3d3aeaa84ea609b55a05e48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4896
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove the JTAG_RESET command from the bitbang execute queue now
that all bitbang drivers have moved away from old reset method.
Remove also the internal reset API in struct bitbang_interface.
Tested parport only.
Change-Id: I12b157ef442f4c9912406b19b7a4d32ba6ec0b53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5300
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The transport SWD uses the JTAG queue to assert/deassert the
system reset srst. This is the major inconsistency that has to be
removed to properly split JTAG and SWD.
Introduce a new driver API, reset(), to controls both the signals
trst and srst in the driver, skipping the JTAG queue. Put the new
API in struct jtag_interface, even if in this patch it's used for
SWD only; the goal is to get it reused by the other transports.
Add the implementation of the API in all the drivers that
implement SWD. Such implementation is almost the same of the old
code in JTAG queue.
Create a wrapper adapter_system_reset() to use the new API and
remove the SWD specific swd_add_reset(). In the wrapper replace
jtag_add_sleep() with jtag_sleep(), because the former uses the
JTAG queue too.
Rename the old jtag_add_reset() as legacy_jtag_add_reset() with
the target to remove it when all drivers would be ported to the
new reset API. Create a new jtag_add_reset() that calls the
legacy function for drivers still on the old reset API.
Use the new API also on JTAG transport for the drivers that can
support both SWD and JTAG.
For the moment, do not modify the implementation of JTAG-only
drivers, which will continue using the usual method. This should
be cleaned-up in future commits.
Change-Id: I32331c88313f6059b25e12c6bb0156aebc1c074f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Create separate memory read/write functions which facilitate access
to the CFI NOR, so that they can be replaced by controller-specific
functions if necessary. This would become necessary when implementing
support for e.g. HyperFlash controllers, which do not directly map
the HyperFlash into the address space.
Change-Id: I1bba1edfd397cb37bfedb43efe2dd03feb26a375
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5145
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Factor out the spansion unlock sequence to deduplicate the code.
Change-Id: Id78522e9a2f0e701870ef816772289d08257476a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5144
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The current code assumes an STM32's flash bank is laid-out in either of
two configurations:
- 4 x 16kB + 1 x 64kB + n x 128kB
- 4 x 32kB + 1 x 128kB + n x 256kB
This is quite ad-hoc but works fine in practice, as long as there are at
least 5 sectors (if n=0). Unfortunately, some newer STM32s are shipping
with only 64 kB of flash (4 x 16kB sectors).
This patch still assumes the same sector layout, but only keeps adding
sectors to the bank if the bank's capacity has not been reached. This
prevents openocd from crashing on some newer STM32s.
Change-Id: If00e5d7a328d11b399babc0bb2111e3ad8a3217e
Signed-off-by: Romain Goyet <romain.goyet@numworks.com>
Signed-off-by: Keir Fraser <keir.xen@gmail.com>
Reviewed-on: http://openocd.zylin.com/4926
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.
Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace the JTAG transport specific command with a more generic
one. Deprecate "jtag_reset" and update the documentation.
While there, fix an error in the documentation, where the command
"jtag_reset" was used in place of command "reset_config".
Change-Id: I41a988d37ce69f7b35a960cbaf5306aab0299b99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5286
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Inspired from http://openocd.zylin.com/#/c/3720/1
Add commands to control the adapter's signals srst and trst.
Add macros for the flag's values assert/deassert to make clear what
they mean and to propose a uniform set of values across the code.
Change-Id: Ia8b13f4ded892942916cad7bda49540a896e7218
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5277
Tested-by: jenkins
- Fix: Proper handling of read_socket() and write_socket()
in case of "partial" read/write.
- Added low-level JTAG IO debug capability (_DEBUG_JTAG_IO_)
- Zero-fill packet buffers, avoid sending pieces of uninitialized
memory over the network (memset struct vpi_cmd)
- Use close_socket() instead of close() - needed for Win32
- Fixed usage messages of jtag_vpi_command_handlers
Change-Id: I8bd19bc5c9512fe8e798600212e8a95213f50f5b
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5177
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In commit cea40152f8 option bytes
reading was changed to direct access to option bytes area.
While there are no problems with stm32f0xx and stm32f3xx chips,
option block (0x1ffff800..0x1ffff80F) is unreadable from locked
stm32f10x chips.
As a result, stm32f1x unlock command writes dirty values to user
options, user data and write protection bits.
Option bytes reading reverted from direct access to option bytes area
to reading currently loaded bytes from FLASH_OBR/FLASH_WRPR registers.
Tested on stm32f100, stm32f103, stm32f107 as well as on stm32f030 and
stm32f303.
Change-Id: Iad476351ffdaca5ace12e02272dacea7f3d08f52
Signed-off-by: Oleksandr Redchuk <real@real.kiev.ua>
Reviewed-on: http://openocd.zylin.com/4940
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use assert to remove "Dereference of null pointer" warnings.
Change-Id: Ie204c234a71758e6470351e1d9f22da3dd887f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5357
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
these commands have been introduced to ease the manipulation of CTI trough
script files, these commands are:
- $cti_name ack $event : to acknowledge a CTI event
- $cti_name channel $channel_number $operation: to perform an operation
on a specific channel, the possible operations are:
gate, ungate, set, clear and pulse
Change-Id: I35463867a3c85072f3776c3aeb1e5788953ec435
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5315
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
-fsize_base should be fsize_addr as it is the address of FLASH_SIZE register
-flash_base should be flash_regs_base to avoid confusion with flash block start
-add LOG_ERROR to functions stm32x_[read|write]_flash_reg(...)
Change-Id: I86f035314bcd616fc0bdf445692d945a85c15481
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5362
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently the code assumes the adapter uses raw SWD, and the expected ID
code of the CPU is even wrong. An adapter speed is also not specified.
All these prevents the config file to be used with ST-Link.
Fix the config file, to allow it to be used with ST-Link.
Change-Id: I1244320fabfe8ee23da5a56a592dbeddc72cc8d5
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-on: http://openocd.zylin.com/5297
Tested-by: jenkins
Reviewed-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The SWO frequency auto-detection with J-Link adapters does not work
properly in the current implementation. This is because the trace layer
has only information about the highest possible SWO frequency supported
by the adapter. With that the trace layer calculates the SWO prescaler
which usually leads to a frequency deviation greater than what is
permitted by J-Link adapters.
Move the calculation of the SWO prescaler from the trace layer into the
trace configuration of the adapter to overcome this problem.
The adapter has the necessary information to choose a suitable SWO
frequency and calculate the corresponding prescaler that complies with
the maximum allowed frequency deviation.
Tested with:
- STM32L152RC Discovery Kit (ST-Link)
- EFM32GG-STK3700 (J-Link)
Change-Id: I38ff2b89d32f0a92c597989b590afe5c75cf4902
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3903
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The field jim_handler_data in struct command_registration is never
assigned, thus has always value NULL. It was added in commit
17a9dea53a ("add jim_handler to command_registration") on Nov 23
2009, together with the homonym field jim_handler_data in struct
command, but never used since then.
Only the field jim_handler_data in struct command is used.
Remove the field from struct command_registration and use NULL
where it was referenced (or remove the assignment if the recipient
is already zero, e.g. allocated with calloc()).
Removing the field decreases the total size of OpenOCD binary by
only 4944 byte on a 64 bit x86. Not a significant improvement from
this point of view.
Change-Id: I9f1d281e3de6b2eb398e2d883c5e9ff92628aecd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5225
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
During code analysis and development, counting again and again the
lines to find the index of the register is a boring error-prone
brain-damaging activity.
Use the c99 syntax and add once forever the array designators to
specify the index values.
The code behavior is not changed.
Change-Id: I2c70f70794475679efb91a8dfadc00f50715bd3f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5256
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When a gpio is exported by writing in /sys/class/gpio/export, the
corresponding gpio control files appear immediately in sysfs but
with default access permission for root user only. The daemon udev
requires some time to get notified of the new files before it can
change the permissions to allow access to unprivileged users.
Due to this race condition, sysfsgpio can fail with EACCES error
if OpenOCD is executed by any unprivileged user.
Give 0.5 seconds to udev to identify the new files and change the
permission.
Tested with udev rules:
SUBSYSTEM=="gpio*", PROGRAM="/bin/sh -c 'find -L /sys/class/gpio/ -maxdepth 2 -exec chown root:uucp {} \; -exec chmod g=u {} \; || true'"
Change-Id: I1316c66ff103ffe23e5e4720f33372dc272a3766
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5302
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The flag extended_protocol is currently a single static variable
thus, in case of multiple targets, it is shared among all the gdb
connections. This is an issue if the gdb connections are not all
using extended protocol, but also when one connection get closed
because the code sets the flag to zero impacting the other
connections still open.
Move the flag extended_protocol in the per-connection struct
gdb_connection.
Change-Id: I19d565f925df6a31767fd8d392242f60867109f2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5310
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The GDB file-I/O remote protocol extension, used for implementing
the semihosting file I/O, requires the length of strings to
include the trailing zero character, as explicitly stated inside a
comment in GDB source code [1]:
/* 1. Parameter: Ptr to pathname / length incl. trailing zero. */
ARM specification for semihosting [2] requires the string length
to not include the trailing zero character, e.g. in SYS_OPEN
specifications:
"field 3: An integer that gives the length of the string
pointed to by field 1. The length does not include the
terminating null character that must be present."
The mismatch above requires OpenOCD to add "one" to the string
length before passing it to GDB. Such conversion is missing
either in the generic semihosting provider of the data, the
function semihosting_common(), and in the consumer of the data,
the gdb_server function gdb_fileio_reply().
The conversion is already implemented in the target specific
function nds32_get_gdb_fileio_info(), but it's not the preferred
place for such GDB specific requirement.
This issue affects the semihosting calls "open", "unlink",
"rename" and "system".
Remove the "+1" conversion from nds32_get_gdb_fileio_info().
Add the "+1" conversion in gdb_fileio_reply().
[1] http://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;f=gdb/remote-fileio.c;h=11c141e42c4d#l381
[2] "Semihosting for AArch32 and AArch64, Release 2.0"
https://static.docs.arm.com/100863/0200/semihosting.pdf
Change-Id: I35461bcb30f734fe2d51f7f0d418e3d04b4af506
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5322
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Using a signed variable as a parameter of FLASH_SNB() macro
generated "warning: The result of the left shift is undefined
because the left operand is negative"
Change-Id: I8b3fe840f9308962460906097df6ddd848c07b25
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5356
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Made sure that size and endianness of jtag_vpi structures sent
over the network is the same, regardless of the platform.
Little endian chosen to maintain as much compatibility
with existing OpenOCD builds as possible.
Matching change in the original jtag_vpi server:
https://github.com/fjullien/jtag_vpi/pull/4
Change-Id: Ib839fea9bb2d5190b5643c970b89333b286dce71
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5152
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The new "Access control list" flash protection scheme used in nRF52840
is not yet supported. Do not prevent sector erase if protection
state is unknown.
Change-Id: Iae9a869a54ffbdc888fb3ec478dafb5c942d9ea0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5348
Tested-by: jenkins
The input buffer size is checked only after writing past its end.
Change-Id: I6a9651c5b7d82efe338468d67bf6caca41004b01
Signed-off-by: Jimmy <nhminus@gmail.com>
Reviewed-on: http://openocd.zylin.com/5352
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Due to lack of printf format check wrong specifier was used and it
actually broke operation on a 32-bit BE host.
So fix this and add the necessary function attributes so that the bugs
like that can be uncovered automaticaly.
Reported and pinpointed by Karl Palsson on IRC.
Change-Id: I254ec28fcd9bb30594d607f74a6dba5456c2c7a1
Tested-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5342
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32H7x7 and STM32H7x5 devices contains two cores : CM7 + CM4
The second core creation is only done when
* DUAL_CORE variable is set to true
* non HLA interface is used
A second check for the second core existence is done in cpu1 examine-end
Once the second core is detected it gets examined.
Furthermore, the script provides a configurable CTI usage in order to halt
the cores simultaneously.
Tested on Rev X and V devices.
PS: the indentation was a mix of spaces and tabs, all changed to tabs.
Change-Id: Iad9c30826965ddb9be5dee628bc2e63f953bbcb8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The STM32H7 has three access ports. The DBGMCU component is available
through AP0 at 0x5C001000 and through AP2 at 0xE00E1000. Using the
latter is preferable for early configuration because it works in all
power states and while SRST is asserted, whereas the former does not.
Change-Id: Iaf8f01d769efb6655040060a8e1e951e1f7e50ab
Signed-off-by: Christopher Head <chead@zaber.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4742
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
functions managing option bytes cache (stm32x_read/write_options)
have bee removed, and a new functions to modify a single option byte
have been introduced (stm32x_write/modify_option).
by the way, some helpers have been introduced to access flash registers:
- stm32x_read_flash_reg(bank, offset, *value): int
- stm32x_write_flash_reg(bank, offset, value): int
and a new commands to read and write a single flash option register:
- stm32h7x option_read <bank> <option_reg offset>
- stm32h7x option_write <bank> <option_reg offset> <value> [mask]
also lock and unlock handlers' have been reduced by using the same routine
(stm32x_set_rdp) and have been optimized to not write options unless
there is a change in RDP level.
finally, several functions have been fixed to lock flash / options in case
of failure.
Change-Id: I75057949ab9f5b4e0f602bafb76f9f80d53a522b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5293
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To achieve that we need to avoid using FLASH_REG_BASE_B0, and use
bank registers instead:
For dual bank devices, each option register is mapped in 2 addresses
at the same offset from flash_bank_reg_base.
This is true for OPTCR, OPTKEYR, OPTSR_CUR/PRG, OPTCCR according to
RM0433 Rev6 (refer to section 3.9: FLASH registers)
In stm32x_write_options, according to RM0433 Rev6, after OBL launch we
should wait for OPTSR_CUR.BSY bit instead of FLASH_SR.QW
Change-Id: Ie24a91f069d03c9233797390fc2e925c737dad90
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5291
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Each bank had to store its options only, there is no need for bank1
to sneak into bank2 options.
Furthermore, some variants do not have a second bank.
Change-Id: I9229eb8ab4b5860ba2b0c5dbe626a54a84bca4d6
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5290
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Drop static pointer to allocated struct nrf5_info, iterate over
the flash bank list to find previously allocated nrf5 instances.
nrf5 is swd only device, so static allocation makes no harm,
but we should avoid copying the wrong code to other flash drivers.
Free sector array before allocating it to avoid memory leak on
re-probing device.
Change-Id: I781d8f4418a91c043f2393e5ecc5278fc6df3566
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4910
Tested-by: jenkins
Also refuse 'flash protect' on any nRF52.
Fail protection check on nRF52840 until ACL protection is implemented.
Change-Id: I84fcf117427e4894147c3ad92e2a3597566b4fcf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4864
Tested-by: jenkins
nrf5 flash driver detected devices by looking up the HWID in the table
of known devices. Unfortunately chips are produced with many different
HWIDs for each type.
All nRF52 devices have FICR INFO field suitable for device identification
without need of HWID lookup.
Some newer nRF51 devices have FICR INFO too although undocumented.
Use this information to identify the device.
nrf5_info() is reworked to show just concise info.
Decoding FICR and UICR registers was moved from nrf5_info()
to a new command 'nrf5 info' without functional changes.
The flash bank for UICR page has the same size as program flash sector.
Change-Id: I900095b9ae23ee995f8e2bef8539b75d00300da5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4848
Tested-by: jenkins
nRF5 flash controller can write a word at a time. Ask flash
infrastructure to handle alignment and padding.
Fix mixing of offset and address in nrf5_ll_flash_write()
- the original code worked just because NRF5_FLASH_BASE is 0
Change-Id: Ibe8bdf899a1764cf4117b2deda1a4618eeb16697
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4819
Tested-by: jenkins
Starting from glibc 2.30, the header file sys/sysctl.h gets
deprecated on Linux, after the commit 744e82963716 ("Linux:
Deprecate <sys/sysctl.h> and sysctl")
https://sourceware.org/git/?p=glibc.git;a=commitdiff;h=744e82963716
The associated NEWS reports
The Linux-specific <sys/sysctl.h> header and the sysctl
function have been deprecated and will be removed from a
future version of glibc.
Latest automake 1.16.1 still does not handle this case.
Current OpenOCD build fails with warning and requires configure
with "--disable-werror" to build.
Prevent including sys/sysctl.h on Linux build.
Change-Id: I5310976573352a96e5aef123352f73475f0c35fe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5317
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritz.fischer.private@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
OpenOCD can be targeted by a Cross Protocol Scripting attack from
a web browser running malicious code, such as the following PoC:
var x = new XMLHttpRequest();
x.open("POST", "http://127.0.0.1:4444", true);
x.send("exec xcalc\r\n");
This mitigation should provide some protection from browser-based
attacks and is based on the corresponding fix in Redis:
8075572207/src/networking.c (L1758)
Change-Id: Ia96ebe19b74b5805dc228bf7364c7971a90a4581
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reported-by: Josef Gajdusek <atx@atx.name>
Reviewed-on: http://openocd.zylin.com/4335
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. This is the only driver not
to have a default case, so add it.
Change-Id: Icb838087bb7525d057a911bd256300e256da1668
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. Make this consistent with
other drivers, and add a 'default' case.
Change-Id: I66d6d0db3fcae93ea246f2d4882ffff5dec14693
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5340
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In preparation for supporting the ARM MCRR and MRRC commands which will
require using two 32-bit registers to read/write a 64-bit internal
register, extract the common logic to read/write from/to a register
to/from DCC and make that parameterized such that we can do this through
not just r0.
Change-Id: Iadb73f5cde8cf5961b5a18ddd198bf39d791e610
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The variable gw16012_port is of type uint16_t.
There is no need for a cast to print it.
Change the format modifier to PRIx16
Change-Id: I16fe688b9d235bae46525635d07849a00fba9548
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GDB uses the vRun packet if available to restart a running process in
extended remote mode. Support this like the R packet and set the
semihosting command-line to allow it to be specified from GDB.
Change-Id: I9cb812b22170630f782113c9927e46e0cd5b1f0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Armv7a is able to read and write memory at un-aligned address, but
only when bit SCTLR.A (Alignment check enable) is zero and the
address belongs to a memory space with attribute "Normal" (see [1]
chapter A3.2.1 "Unaligned data access"). In all the other cases
the memory access will trigger an alignment fault data abort
exception.
Memory attributes are explained in [1] chapter A3.5 "Memory types
and attributes and the memory order model".
Disabling the MMU cause a change in memory attribute, as explained
in [1] chapter B3.2 "The effects of disabling MMUs on VMSA
behavior".
This can cause several issues. e.g. a SW breakpoint on un-aligned
4-byte Thumb instruction, set when MMU is on, can be impossible to
remove when MMU turns off.
While is possible to check all the possible conditions before an
un-aligned memory access, it's clearly more maintainable to skip
such complexity and only perform aligned accesses.
Check the alignment and eventually modify the data size before
calling the functions cortex_a_{read,write}_cpu_memory_slow().
Change the comment in the two functions above to comply with the
new behaviour.
[1] ARM DDI 0406C.d - "ARM Architecture Reference Manual, ARMv7-A
and ARMv7-R edition"
Change-Id: I57b4c11e7fa7e78aaaaee4406a5734b48db740ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5138
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Correct check for end-of-region is:
$BASE + $LEN > $ADDRESS
And it is currently (wrongly) calculated as:
$ADDRESS > $BASE - $LEN
Change-Id: If10bfee19b0c7dbc085731ac1eda943f5d8a36a3
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Make driver_priv point directly into the corresponding chip bank structure
and add a pointer to it to get back to its chip when it's needed. This
removes the need to keep track of any bank number, either global or chip-
local.
In addition, it simplifies the cases where the chip structure was just used
to access the chip bank fields; now they are directly accessible.
Change-Id: Iaa353cd4fa7d8ff94c2ef69028c7cb32fade0420
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/4775
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The preverify option allows to check whether flashing is necessary.
If the target is flashed often/automatically this can save time and
preserve the flash. This is expecially helpful in CI environments.
Change-Id: Iead0a269e1a772b751d4dd9e8b53b2fecc874624
Signed-off-by: Moritz 'Morty' Strübe <moritz.struebe@redheads.de>
Reviewed-on: http://openocd.zylin.com/5292
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
I think that libusb_handle_events_timeout_completed is supposed to make
progress or time out, but sometimes we hit a case where it makes no
progress, and mpsse_flush() loops forever. This wall clock timeout
notifies the user that this is going on.
When I wrote this code, this bug would reproduce every hour or two, but
right now it's not happening for me.
Change-Id: I7eb66f43462298e263a48048aa0c8769095661eb
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4767
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the reference manual it should be 0x40000000. Flashing (and
booting) a firmware with this MSC base was successful.
Change-Id: I739e67d36555b8170a3b8e26f54cf1c09ce8424b
Signed-off-by: Christian Meusel <christian.meusel@posteo.de>
Reviewed-on: http://openocd.zylin.com/5263
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix expression "(pin_status | 0x4)" which was always true rather than
testing a bit. Untested - was clearly not expressing the intent of the
author by inspection. Found by automated tooling and rtrieu@google.com.
Signed-off-by: Seth LaForge <sethml@google.com>
Change-Id: I4bb91e60e8ce9757bf21976cc48de6f85a39c68d
Reviewed-on: http://openocd.zylin.com/5301
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The C standard says that errno is set to ERANGE if an out-of-range value
is returned by strtol, strtoul, et. al., but it does not say that errno
is cleared if the function is successful (and, indeed, it is not on
glibc). This means that, if errno is ERANGE before strtol is called, and
if the value to be converted is exactly the maximum (or, for a signed
conversion, the minimum) legal value, COMMAND_PARSE_NUMBER will
erroneously indicate that the value is out of range.
Change-Id: I8a8b50a815b408a38235968f1c1d70297ea1a6aa
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5298
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PAGE_SIZE is defined in system includes on some systems, this would
avoid the unintended conflict
Fixes
| src/flash/nor/esirisc_flash.c:95:9: error: 'PAGE_SIZE' macro redefined [-Werror,-Wmacro-redefined]
| #define PAGE_SIZE 4096
| ^
| /mnt/a/yoe/build/tmp/work/core2-64-yoe-linux-musl/openocd/0.10+gitrAUTOINC+7ee618692f-r0/recipe-sysroot/usr/inclu
de/limits.h:89:9: note: previous definition is here
| #define PAGE_SIZE PAGESIZE
Change-Id: I195b303fc88a7c848ca4e55fd6ba893796df55cc
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Reviewed-on: http://openocd.zylin.com/5180
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is no sense in displaying the max size (2M) as there is variants
of this device with reduced flash size
Change-Id: I40574064d75fdf2a038044c81038a6d7abc6c4dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5288
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added "exist=true" field to the reg_list struct to make access to the
dsp563xx registers again possible. Without it defaults to exist=false
and all the reg related functions will return nothing.
Fixes regression from b5964191f0
Change-Id: I9c256346735b8d66919c4ba83f528a8afca46ff9
Signed-off-by: Han Hartgers <han.hartgers@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5239
Tested-by: jenkins
Fix two expressions where precedence of operator | vs ?: was clearly confused.
Untested - was clearly not expressing the intent of the author by inspection.
Found by automated tooling and rtrieu@google.com.
Change-Id: I46f190154797f8affc761caf3a15a1a9db53d702
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/5281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
1. Add get_thread_reg() to rtos. It's used in rtos_get_gdb_reg() to read
the value of a single register, instead of reading all register values
by calling get_thread_reg_list().
2. Add set_reg() to rtos. gdb_server uses this to change a single
register value for a specific thread.
3. Add target_get_gdb_reg_list_noread() so it's possible for gdb to get
a list of registers without attempting to read their contents.
The clang static checker doesn't find any new problems with this change.
Change-Id: I77f792d1238cb015b91527ca8cb99593ccc8870e
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5114
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is causing repeated build failures. Its design is so fundamentally
broken that if someone actually wants to use it, a full rewrite is the
only option. So it's not even worth deprecating in the hope that someone
will notice and fix it, just get rid of it.
Change-Id: I513069919a3873bd69253110f7fb6f622ee7d061
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5243
Tested-by: jenkins
Reviewed-by: Jeffrey Booher-Kaeding <Jeff.Booher-Kaeding@arm.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
Without a better replacement of the command, it's worth fixing it.
Accordingly to ARM DDI 0403E.d, chapter C1.4.1 "Entering Debug
state on leaving reset state", to halt the core at reset both bits
DHCSR.C_DEBUGEN and DEMCR.VC_CORERESET must be set.
Current code only sets the latter bit, relying on having C_DEBUGEN
already set through other commands, e.g. "halt". This prevents the
command "soft_reset_halt" to work if issued as very first command.
Set the bit C_DEBUGEN in command "soft_reset_halt".
Change-Id: I66bfd6a0da1fca5049dea037b4d258cf6f842966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4987
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Thanks to command_run_linef() there is no need to pre-build the
command using alloc_printf().
Change-Id: Iccfebd6063d1ac162f090fe2309b1f51bebf0214
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5226
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The `command_run_line` function contains a comment saying it should be
reentrant. However, it isn’t: it NULLs out `current_target_override` and
doesn’t restore it before returning, and it changes the `context`
associated data of the `interp` object and then deletes that associated
data before returning rather than restoring it to its previous value.
Change-Id: I84fd46ef7173f08cf7c57b9a5b76e4986a60816f
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5223
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extra whitespace in file creating build errors with makeinfo.
Change-Id: Ib764850c1c8ff596d3c753eadd8e27f8c5982d20
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/5229
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.
Please refer to ARM documentation for more information about SSE-200 and
Musca A.
Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds ARMv8-M CPUs detection logic in ARMv7m target specific code.
Also adds a slightly different watchpoint manipulation logic for ARMv8-M.
This is based on ARMv8-M architecture reference manual.
Tested on ARM Musca A board.
Change-Id: I0652560954ef02c378a7067fab586edf39d3e9cc
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4997
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I1b917a4c1205115c4e0315373d81a9305e931258
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4944
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I32c43e2e47366363521fa3f387de9e2fb1c20852
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4943
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of jtag's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition.
It can be tested running openocd on a jtag target and adding a
jtag event "setup" with a single line "return", e.g.
openocd -f board/ti_cc3200_launchxl.cfg \
-c 'jtag configure cc32xx.cpu -event setup return'
to get the message:
../src/jtag/core.c:1599: Error:
in procedure 'jtag_init' called at file "../src/jtag/core.c",
line 1599
Modify jtag_tap_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I6d6febc15ef169638afffbffc1810e0b84fcf5c8
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5199
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c2e18bfaea changed the size of the JTAG-to-SWD sequence
from 15 bytes to 17 bytes. This broke SWD switch sequence transfer
for buspirate, since buspirate packets can only hold a payload of up
to 16 bytes and we tried to fit the whole sequence in a single packet.
Splitting up the sequence transfer in appropriately sized packets
makes buspirate SWD work again (successfully tested with buspirate
firmwares v6.1 and v7.0).
Change-Id: Ib5b412b9e77287d705d2762e31c16d30318b50e3
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Reviewed-on: http://openocd.zylin.com/5200
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The macro TARGET_ADDR_FMT, defined in helper/types.h, already
includes the prefix "0x" in front of the hexadecimal number,
being defined as:
#define TARGET_ADDR_FMT "0x%8.8" TARGET_PRIxADDR
An additional "0x" is present in mem_ap; it prints debug messages
with a double "0x" before the address:
Debug: 2921 34180 mem_ap.c:153 mem_ap_write_memory():
Writing memory at physical address 0x0x5000000c; size 4;
count 1
Remove the incorrect hexadecimal prefix.
Change-Id: I38f19ed2a2f542bd5df53e947a2604f1cbe80e08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5222
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
To support 128 bit registers, the rtos_reg structure value
array needs to be updated from 8 to 16 bytes.
Tested by reading ARMv8 NEON FP regs on an Ampere eMAG 8180 with GDB.
Change-Id: I7f3fe1a5b2def599d021787fbe9cdd51f92859a4
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5209
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The ARMv7-A architecture supports super sections which allows mapping
physical addresses up to 40-bit into a 32-bit virtual address using the
short descriptor format (see ARM DDI 0406C.c section B4.1.112 for
details).
Change-Id: I8e64d0e93e36ae7a7da7b7bf2a8342856bb044f1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5212
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In preparation for adding super section decoding, do not restrict
armv7a_mmu_translate_va_pa() to 32-bit virtual addresses since ARMv7-A
processors with VMSA extensions (including LPAE) can issue wider
physical addresses. Update casting to uint32_t where necessary.
Change-Id: Id1c3d0d5ac324cbdc334259d9ea75fe4981671a1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5211
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function is not used anywhere in the tree, remove it, such that we
only have a single function moving forward that might need to deal with
short vs. long format specifics.
Change-Id: I80e81cd7eba1e028d1afaeaedb675b46c0ca6fa1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Check earlier that the read of the PAR register was successful instead
of starting the decoding and then checking for an error reading that
register.
Change-Id: Id96c2b2f76d2d1c745fcfa55ad4c1e6db92106f9
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The prefixed commands has been removed in commit 0840414f0e
("helper/command: do not replace new commands with ocd_ prefix").
Change-Id: I9f101beb85533973041386896bbb215bb141962f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5191
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For legacy support, drivers that do not define a list of
transports get identified as jtag_only.
Cleanup this old crust and initialize properly the transports
field in the jtag_interface for all the drivers.
Change-Id: I9c86064e5d05bd0212bc18f4424414e615e617fe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In the initial commit 6c9b804d61
in 2007's svn://svn.berlios.de/openocd/trunk@246
a target script gdb_program_config was called before gdb flash
programming. To guarantee the script does not left any pending
command in the jtag queue, a call to jtag_execute_queue() was
inserted after the execution of the script.
In following commit ef1cfb2394
in 2008's svn://svn.berlios.de/openocd/trunk@975
the script was replaced by the event "old-gdb_program_config" and
the call to jtag_execute_queue() get executed in every case, even
if the event handler was not present.
At last, commit bb3793c9a4
("target: remove legacy target events") stripped away the
obsolete event but left the call to jtag_execute_queue(), now
completely useless.
Remove the call to jtag_execute_queue() and clean-up the code
around it.
Change-Id: I284f54d656d431ad6cdc25ca18218c09db31bd25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4911
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since the first commit 09883194f8 that introduced cortex_m, the
code has a delay of 50ms after srst has been asserted.
The specific delay is implemented through the JTAG_SLEEP command
sent in the jtag queue.
To remove the dependency from the jtag queue, replace the delay
with a transport independent function.
In case of jtag transport, this change keeps the same behaviour
only if the jtag queue has been flushed before the delay. This
does not happen if the call to dap_dp_init(), few lines above,
fails while calling a dap_queue_dp_{read,write}(); in this case
the jtag queue will be flushed later, after the delay, while in
the original code the delay would follow the flushing of the
commands already queued. Anyway, this different behavior would
only happen in case of DAP already not responsive so anticipating
the delay in such error condition is not supposed to add further
problems.
Change-Id: If15978246764e4266b10e707d86c03e5ed907de7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4912
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is just a single entry point for the jtag API .khz(),
.speed_div(), .power_dropout(), .srst_asserted().
Simplify the code by in-lining the default handler.
The overall code behaviour is not changed.
This change prevents modifying at run-time the content of
struct jtag_interface.
Inspired from change http://openocd.zylin.com/943
by Evan Hunter <ehunter@broadcom.com>
Change-Id: I09aeb76d614db57b1884ac7ee9f00c152cd77849
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4892
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The specific SWD API to change/query the adapter speed is never
called because the equivalent JTAG API is used in place of it.
In the restructure of struct jtag_interface, the JTAG API is
promoted as global adapter API, thus a specific SWD one is not
anymore required.
Change-Id: I1e810d255b4dfcd5791b4fac8ae1260c31a057fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4891
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently size of the GDB buffer is 16384 bytes but it is treated as
nul-terminated string in most of the code, so effective size of the
buffer is actually 16383 bytes. OpenOCD responds with `PacketSize=3fff`
to qSupported request. Result of GDB's `m` command is encoded in hex so
each data byte uses two bytes in the buffer. As a result GDB will split
bulk read requests into chunks 0x1fff bytes each. This causes troubles
on targets (or memory regions) which support only aligned, word-sized
access (such as MMIO buffers).
Steps to reproduce (psoc6 target):
gdb> dump binary memory dump.bin 0x040320000 (0x040320000 + 65536)
OpenOCD:
Error: Failed to read memory at 0x40321ffe
Error: Failed to read memory at 0x40321000
Error: Failed to read memory at 0x40323000
Error: Failed to read memory at 0x40325ffe
Error: Failed to read memory at 0x40329ffa
Error: Failed to read memory at 0x40329ffc
Error: Failed to read memory at 0x4032bffc
Error: Failed to read memory at 0x4032dffa
Consolidate GDB_BUFFER_SIZE usage: ensure size of each buffer is
(GDB_BUFFER_SIZE + 1), add explicit comment that additional byte is used
for nul-termination. Report correct size of the buffer to GDB (0x4000)
as recommended in GDB's docummentation: `if the stub stores packets in a
NUL-terminated format, it should allow an extra byte in its buffer for
the NUL`
Checked with clang-asan, clang-analyzer, valgrind - no new errors.
Change-Id: I909e8a2c6b010c5d4a304641808d4a807a4ec18d
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/5109
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The warning appears for every possible device during enumeration
and provides no useful information for an end-user.
Change-Id: I56e7889a5d9d4656de13ad9e21be3a6e1906e05f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By definition the EXTERNAL bit in Debug Fault Status Register indicates
that an external debug request (EDBGRQ) signal was asserted.
Usage example: this could be done by CTI in multicore devices in order to
halt all the cores together.
Change-Id: I7830455ce5da6702b7d08c8fa7bfe80e4d8a5055
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5157
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 89fa493a3b removes the top
level command "unknown" and adds in command_unknown() some unclear
code that should detect a user-implemented "unknown" command.
But, all the commands that trigger the execution of the function
command_unknown() are registered in register_command_handler() and
have the command name prefixed with "ocd_".
Due to such "ocd_" prefix in cmd_name, the condition
if (strcmp(cmd_name, "unknown") == 0) { ... }
is always false.
Nobody complained for almost 10 years so we can proceed to remove
this dead code, before merging any change that obsoletes the
prefix "ocd_" and potentially makes the condition true.
Remove the dead code guarded by the condition above.
Change-Id: Icf11a956bb2d68fc84e6eb5779edf8e35db8fa53
Fixes: 89fa493a3b ("remove unknown handler")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The documentation added for commit b3d29cb544
was merged after the end of the eSi-RISC section rather than AARCH64.
This patch relocates this hunk to the correct location.
Change-Id: I46a2d24442556e9e8000b46a5e1af03b83de6d98
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/5181
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The V3M SoC is R8A77970 while the V3H SoC is R8A77980 . Update the
CHIPNAME and swap the SoCs to keep the list sorted.
Change-Id: I7e1777c0c7181e5e0beac98333f2047cb443d0df
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5140
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H target.
This is an SoC with one Cortex A9 ARMv7a core and
up to 10 MiB of on-SoC SRAM.
Change-Id: I20fd54b385fe1ba1cc325451c3fdfa3a835d4884
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H GR-Peach board,
which is a cheap development kit for the RZ/A1H SoC.
Change-Id: I7f5596ae47e6dff8e6d06cffd4dddca20f57d0ca
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In case of error, a command should use command_print() to report
the error message, so it get printed only on the session that run
the command itself, and the message can be intercepted with the
tcl command catch if it has to be handled differently.
Current code drops the command output when the command returns
error, claiming that it's the command that *should* have printed
it already. This is true only if we *abuse* of the LOG functions,
but accepting the side issue of having the LOG printed in every
session and being unable to catch{} the error message.
Since we have switched to command_print(), change the code to
propagate the command output also in case of error.
Change-Id: I95de424a65e63702bdb3b2277749a0ac6aaaa503
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5178
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Two calls to command_print() in imx_gpio fixed - the first parameter
adjusted (CMD_CTX -> CMD) per the changes from this commit:
6cb5ba6f11
Change-Id: I6cb0909439a632d3109edfc68070b9b561f86d49
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5176
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The commit 84ca4995ad ("drivers/bcm2835gpio: fix usage messages")
has been merged before commit 6cb5ba6f11 ("helper/command: change
prototype of command_print/command_print_sameline") introducing two
new call to command_print() that were not modified by the second
commit.
This triggers a compile error on ARM host.
Fix the incorrect function call.
Change-Id: I2736bae24141685b7590fd6b4aa5e6a29b2cab29
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5174
Tested-by: jenkins
In jtag_vpi_stableclocks() the TMS line needs to be set properly
based on the current JTAG TAP state (TMS=1 in TAP_RESET state vs.
TMS=0 in other cases).
Change-Id: Id49622ba83015f97b61b6a896edde4448f1fbdc6
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5151
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commit "helper/command: do not replace new commands with
ocd_ prefix" breaks the print of usage text when a multi-word
command is typed incompletely.
Fix it by explicitly running the "usage" command.
Change-Id: I46f8e521d9b6ac617bff8938cf8fc96f0ade45c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5166
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When opening multiple telnet connections, the command output on
one console is broadcast to all the other console.
Send the command output only to the output handler that has been
set for that context.
For the moment, still broadcast the errors.
Note that contexts which doesn't explicitly set the output handler
(e.g. gdb_server), will inherit the global output handler
configuration_output_handler() that will broadcast the output.
Change-Id: I1f2d6e6a3bbf730f5fa77246730fce1445742a1e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5093
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Part of the output is generated with log functions.
Change prototype of find_target() and use command_print() for all
the output of the command.
Change-Id: Ia9fdb653fd5b27be427381053a037545faa34414
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5092
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The commands prefixed with "ocd_" are removed.
Remove them from configuration files.
Change-Id: Ib44627ee17a39f3d06b479507ab5a025073bf9a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5090
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The commands prefixed with "ocd_" are removed.
No need to review the documentation.
Change-Id: Idad95e62f6c8574ff8b61930aeef04e9727fae8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5089
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The commands prefixed with "ocd_" are removed.
Remove any reference in the documentation.
Change-Id: I27cebaa4752752ec8700757bf1c98b267c24f15b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5088
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
We do not register commands with special "ocd_" prefix anymore.
Change-Id: I588816eb22c2435a97be5fbfa87ee5584274b02f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Once the wrapper "ocd_bouncer" is removed (which was the only user
of this command), there is no reason to keep the command any
longer.
Remove it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I979ce1c147babedb44dd77418751133f589f827c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5084
Tested-by: jenkins
The TCL return values are now consistent, no need anymore for the
hack of registering the commands with "ocd_" prefix and override
them with proc ocd_bouncer.
Clean-up the command registration and remove the proc ocd_bouncer.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2a467e73ecb068686ea3fda91bf961aba6db6427
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5086
Tested-by: jenkins
Command's output should be put in JimTcl result.
We should not anymore capture the log output and pack it as a
JimTcl result.
Remove the log capture feature in script_command_run().
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Id326c8719e1cee9156d7fc15ae8355ec79a74951
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5085
Tested-by: jenkins
Rationale:
1. There's logging output and there're return values;
2. If a function should return something, it should do it explicitly,
same for logging;
3. Interactive interfaces (telnet, Gdb and Tcl RPC) must always return
the result of the evaluation for the given expression. You can
suppress this output by adding ``; after 0'' to the end of your
expression.
4. Some commands "throw an exception" and if you want to be able to
collect both the return value (when it succeeds) and the log output
(when something goes wrong) you can use do like this:
set log_output [capture "catch {reset_config} return_value"]
So what I'm proposing is following:
1. Every jim_handler command should set the return value the standard
JimTcl way, without any tricks. If it needs to print some logging
output, it should use LOG_* functions.
2. The usual commands (COMMANDS) can easily construct their return
value by appending strings with command_print() and
command_print_sameline(). This required changing "struct
command_invocation" and passing a pointer to it to command_print*
functions.
The code is already functional, please test and comment.
TODO items:
1. Modify all jim_handler commands to properly return or log values
(some of them are commented out for now in this patch).
2. Properly document "capture" command and provide a convenience
function to automate log_output + return_value gathering.
3. Add appropriate Doxygen comments.
4. Add Tcl RPC interface description to the manual, all the example
clients in different languages (from the mailing list) to contrib/.
This change is the core part of http://openocd.zylin.com/1815 from
Paul Fertser. It has been extracted and rebased to simplify the
review and provided again as 1815.
Change-Id: I675c91aa9da1e4e7c6f0a8fe6112a00550b9e4db
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/1815
Tested-by: jenkins
The command uses LOG_USER() instead of command_print().
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92e5e5954a75b96093b3ed6af73a7536c063b639
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5083
Tested-by: jenkins
After replace CMD_CTX with CMD, the indentation is incorrect.
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5d7c40227ceda2e9db8dab88088d74012d2254c4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5082
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of show_config*() functions to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I131a904774bf60ad1bf9d90dbc65927c246ac23a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5080
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_dump*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia43bff112372cbb76e1aea9f59f4a9b6df05c15d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5079
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_analyze*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ie7cfd323fe591a987ea648a20be2bb9c7273dde8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5078
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of binprint() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5ebdc50417d97c791c98ac0cfe2218319809eb7f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5077
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_set() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: If00f9cfb784b53bb3df92d4469178e2f930a146a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5076
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_list() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibff636d476bcd59784ce3da5409d930225cfe637
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5075
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2150201fad3fd3bc0be89249dcbd314b38a6f860
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5074
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of dap_rom_display() and dap_info_command() to
pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Idb97b20759c03fcecbac1184c354966f469caa5f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5073
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of etmv1_analyze_trace() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic923af5480a54c7272d2ff1abbe235ba941cf1a0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5072
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_iod_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I67f594c80d6bbbbf6c9567069a545f16877b1e94
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5071
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm7a_handle_l2x_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib926cd7380ac8b6fb89f64e0a85d81d124633315
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5070
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv7a_handle_cache_info_command() to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I27f507869cb41c74722a759e69dfd45658fcd4be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5069
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv4_5_handle_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib6ab3ec2fc6504c2a0635b654697a4b6e12a3750
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5068
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib0b84c933689ac8c940c9bbe62d9c95fd015c4f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5067
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of display_cache_info(),
armv8_handle_inner_cache_info_command() and
armv8_handle_cache_info_command() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I13519c79af82cdba57d5205ba84a5a27fce65a36
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5066
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_display_instruction() and of
xscale_analyze_trace() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8420f19c1b2ff0d2a2f2a8d3627767f7acda437c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5065
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Id047fab41ec4f673a46756b0ab901e659e088544
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5064
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips_m4k_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9fa3e883d2ca9cc858caaefd33586f78638702f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5063
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips32_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic4a4de10518ee009d6df420e7278fd028e1f22ca
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5062
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of cortex_m_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Icf6d1e5f8b4a3ce115c4253e49769df19a5211ae
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5061
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm946e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib7119e2b009d05eec47b50c3b9d32feaebc97538
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5060
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm720t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7fa0628fabacd9ceb62ce921192f88edca659c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5059
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm966e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92745591256ad56a588b6386842028e0b18dec96
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5058
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm926ejs_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibbb03429a7fe8b9979f9bb9e513f9eb86aee3b5b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5057
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm920t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9a603d7c032df91b3913aadb242de89dbed0358e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5056
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam4() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8dfa66f3f6be318d6ba89649279b1b4502f375d9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5055
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam3() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia1e7af79d0fc89d229b4e10df37317a374bbab62
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5054
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Pass CMD instead of CMD_CTX as parameter to nand_list_walker().
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia11887dfc6dc58d5458a88ba84780cd895b8c253
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5053
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of nand_fileio_start() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7993f6aba997a2d2917949563651c8d0c213730d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5052
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
When dumping traces or semihosting text, the command that enabled
it is already completed, so CMD is not a valid value.
Plus, we want the dump to be printed in the command context where
the enable command was executed.
Replace command_print() with command_output_text().
Change-Id: I297a2b799a914233499641062407cf6e8b9fe012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5051
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Current code provides two independent implementations for the
memory read/write commands:
a) jim_target_md()/jim_target_mw() for the target specific
commands "<target> m[dw][bhw]"
b) handle_md_command()/handle_mw_command() for the current target
commands "m[dw][bhwd]"
The case a) misses the handling of doubleword and calls functions
command_print_sameline() with first parameter NULL because defined
as jim handler.
Remove the code in jim_target_md()/jim_target_mw() and use the
same code in b) for the target specific memory read/write.
This approach also provides support for 64-bit data size, not
present in the implementation in a).
The only drawback is that the implementation of memory read in b)
prints the data also as human readable ASCII characters, feature
missing in the implementation in a). This could introduced later
if it's really needed.
Update the documentation to:
- add 64-bit support
- add phys parameter
- add the count parameter
Add attribute "unused" to target_buffer_get_u8(), now not used
anymore.
Change-Id: Ib11ff924c409ad87e77fe708d628b2cc82b74d6a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5050
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Events are supposed to be executed asynchronously and not linked
with any command, so it's incorrect printing out an eventual error
using command_print().
Even in the case of events triggered by the command
<target> invoke-event <event-name>
the eventual error in the event handler is not propagated to the
command, so the command_print() is still not appropriate.
Replace command_print() with LOG_USER() in target_handle_event().
Add further info in the log to identify which event has generated
the error and its associated target.
Before return, clean-up the error message and the stacktrace from
the error already displayed, to avoid propagate them.
Change-Id: I5966aa25e7c81348f4ad4d6e7ce5d4dee44ea4c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5049
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of target_process_reset() to pass CMD instead of
CMD_CTX.
Replace NULL parameter of command_print().
Remove extra newline, already added by command_print().
Change-Id: Ieb820c2586e1ff74a0c2b63a9c8693ca7710dfb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5048
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Accessing the variable "cmd" in a COMMAND_HANDLER is confusing
because the variable definition is not visible in the prototype,
thus "cmd" can be identified by the reader as a global variable
defined somewhere else.
Add the new macro CMD to make more evident it is a part of the
COMMAND_HANDLER.
Change-Id: I8f63da593a931045cc404323f143b88c5c80ab5e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5047
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
jim_arm946e_cp15() used command_print() in the jim handler.
Change-Id: I0a258aad5a60f45672b9b6fa6819691507d4f0f6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5000
Tested-by: jenkins
jim_target_event_list handler used command_print() in jim handler.
Rewriting the jim handler to the OpenOCD command is easy
as get_current_target() returns proper target for prefixed commands since
bb9d9c6026
Change-Id: I3e937249386ca5dbd7a5dd6ebb0ccde0911325d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4993
Tested-by: jenkins
Based on RM0433.rev5 > Section 3.3.9 : Flash program operations:
QW1/2: this bit indicates that a write, erase or option byte change
operation is pending in the write queue or command queue buffer.
It remains high until the write operation is complete.
It supersedes the BSY1/2 status bit.
On this basis, stm32x_wait_status_busy is renamed accordingly to be
'stm32x_wait_flash_op_queue'
Note : In this commit there is a fix of SR_ERROR_MASK value in flash loader algo
Note : This modification is mandatory for revision X, and backward compatible
with old revisions
Change-Id: I59d2973317d76b01fbb0fb5e4a472a47d0a7a5b5
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4883
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add mem_ap for direct access to axi bus (without halting cpu)
* Mark m4 core with -defer-examine because it's not used by default
* Make a53.0 default target since it's the boot core
Change-Id: Id031533c5d4af346eb08a9ac2532fa1bca602913
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5036
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 the 6UL 6ULL 6ULZ chips are based on Cortex-A7
which is at a different address so a custom script is required.
Tested on imx6ull-14x14-evk
Change-Id: I72822d2241045c318389fadbc66d7aaabaaf4cb5
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5040
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 a Cortex-M4 was added with a second CoreSight
DAP so a separate script is required.
Tested on imx6sx-sdb running linux
Change-Id: I1561910b233015f42508f341175822c0827655ec
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5041
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike imx7d/solo supported by imx7.cfg the M4 core is on a different AP
and is always running by default so no -defer-examine is required.
There is also only one Cortex-A7
Tested on imx7ulp-evk
Change-Id: Ifa923d1b9a372c788e6654bc2233fd4d9073a32d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5043
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit b04c7c2ca5 adds the cross
reference target "adapter_usb_location", but references it with
the command @xref inside a text, where command @ref should be
used. This triggers a compile warning:
doc/openocd.texi:2517: warning: `.' or `,' must follow @xref, not c
Replace @xref with @ref and adapt both the text and the command
syntax.
Change-Id: I1520ffecb7d1d375f924492b1884d5b47f399007
Fixes: b04c7c2ca5 ("ftdi: use "adapter usb location" instead of
ftdi_location command")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5045
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add a config to access the Amazon Kindle Model No. D00701 and D00801.
Both ebook readers are based on a Freescale i.MX31. A JTAG interface is
included in a 40 pin FFC connector marked "J9" on both variants.
Change-Id: I58bb1ded3d6706bc3798af488ca8bafb7dc45225
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3956
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
We have the function to wait for bits in dscr. Use it whenever
possible.
When the bit to test is DSCR_INSTR_COMP, use instead the wrapper
function cortex_a_wait_instrcmpl().
Change-Id: I5c54c239a00f489712af448eb97752210b4b38b8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In function cortex_a_wait_dscr_bits() the last read on dscr gets
ignored in case of timeout, even if it finally provides the value
that would trigger a successful return.
Check the returned value before testing the timeout.
Also, print a message on failure reading dscr.
Change-Id: I261ac1545113db39374833a55be911a4da71d893
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5112
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Depending on adapter speed, the function cortex_a_poll() can take
time to execute and can complete successfully when the timeout is
already expired. Checking the timeout at function return causes a
timeout error while that could be avoided.
Check the target status at cortex_a_poll() return, before checking
for the timeout.
Change-Id: I4c1581f6e718298c566df7b1359255e16e3955d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5111
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
`maskisr steponly` disables interrupts during single-stepping but
enables them during normal execution. This can be used as a partial
workaround for 702596 erratum in Cortex-M7 r0p1. See "Cortex-M7 (AT610)
and Cortex-M7 with FPU (AT611) Software Developer Errata Notice" from
ARM for further details.
Change-Id: I797a14e4d43f6dcb3706528ee4ab452846ebf133
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4673
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The modified lines cause "runtime error: left shift of <X> by <Y>
places cannot be represented in type 'int'", because integer
literal is cast to int by default.
Change-Id: Ie38119b5eb46ee470e0d149959e523b48ac4d66d
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5005
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Bit 29 of OPTSR is IO_HSLV. It ought to be read in stm32x_read_options
and written in stm32x_write_options. Adjust the bitmasks to do this.
Change-Id: I785a5291c991c98b774177f960dc58f2b5e045e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4745
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Every command has been fixed with proper usage field.
Change LOG_DEBUG with LOG_ERROR so a developer will get a visible
alert for missing usage field when adds a new command.
Change-Id: I077c3745fd6265aded8e54b3f9d202d4d6516966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5026
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Copy all SJC TAPIPs from imx6 reference manuals.
Some imx6 chips are based on Cortex-A7 or have an additional Cortex-M4
and need separate scripts.
Change-Id: I3b07d94058c2c5e6313cfc8bb43134a90682a62e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5034
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
OpenOCD scripts are usually indented with 4 spaces but here there are 8.
Change-Id: Iaad53e3b377d246d99119bb7bb5fd75d4422f564
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5039
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Looking through imx6 manuals all of them claim that "In follow-on
silicon revisions the ID value is subject to change by incrementing the
first nibble".
Handle this by passing -ignore-version to jtag newtap command.
Change-Id: I7fc4779f9757d527ea20a5174a8c90f919580013
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This can be used to dynamically distinguish between similar chips in tcl
code.
Change-Id: Ic4dfb61693e78616355173142dc7f9b9683a9f73
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5033
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In Texinfo, a comma inside an @url separates parameters to the @url
function rather than being included as part of a parameter. Use @comma{}
instead to resolve this.
Change-Id: I8b38939462cf4452e5bc2582ee484220aaf83ae0
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5028
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch remaps the Flash over ITCM region as virtual to ensure that
any breakpoint placed in this area will be automatically set as an
hardware breakpoint. This patch is a fix to a regression introduced with
changes #4429.
Change-Id: I03d46d8537ef06b33a3d4a2328274667c6481969
Signed-off-by: Rocco Marco Guglielmi <roccomarco.guglielmi@gmail.com>
Reviewed-on: http://openocd.zylin.com/5097
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
By using the command "add_help_text" to add a help text to a TCL
procedure it implicitly creates a new command_registration struct
that has field .usage set to NULL. This triggers a debug message
BUG: command '%s' does not have the '.usage' field filled out
Use an empty string if usage field is NULL.
Plus, do not annoy the user with a LOG_INFO when the command
"add_usage_text" replaces an empty usage.
Change-Id: I4a72646e0fb704ba354f938d774055540cde3967
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5025
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command '%s' does not have the '.usage' field filled out
While there, fix some minor typo in the help messages:
s/deasert/deassert/
s/Deasert/Deassert/
Change-Id: If3dd18265cda103ca0d05609f67f4ca58e7cbb27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5024
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command 'swd' does not have the '.usage' field filled out
Change-Id: I5a36c0fc822c4d5d74ef2d1c75e369648c6f7d4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4830
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove the numeric parameter <bank> from help and add it to usage
Change-Id: I630ca5450955210299f54e16fe5c9e8e51b3b266
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5022
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands bcm2835gpio_speed_coeffs
or bcm2835gpio_peripheral_base are executed with empty command-line.
Change-Id: Ie45d8268c1de331aded0bb52d5e6b8f0e8766a5b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5019
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands imx_gpio_speed_coeffs or
imx_gpio_peripheral_base are executed with empty command-line.
Change-Id: Id56a68622817101bd0a46fed1fead6d2cd2b6ec6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Chained command require a subcommand as first argument. The usage
field for chained commands is not really important because the
"help" command will list all the subcommands with their respective
usage.
Add a empty usage field on all chained command.
The command "jlink config" can be either followed by a subcommand
or used alone, so use a dedicated usage string.
Change-Id: I43c3f8a766f96a9bdab4e709e3c90713be41fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5017
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: I900924600753ee7a72ca45da13db4112ab4b1522
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5015
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: Ie69d9d6a786e1ef0abbcfd3eef89a61206238ebe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5014
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: Iefaeb15cc051db9f1e0f0140fe2f231b45f5bb12
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5013
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I65d32870bf4d3df845db69682fe445c71642f976
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I9ef7ac08e7cd5b82a6a7896c47017943d668925f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5011
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I743457acf7757df4646c9bc4e5ea1a6f9c841516
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5010
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The struct log_command_handlers[] is never modified.
Add const qualifier to it.
Change-Id: I5785aeb09ae9c23eaf7c34a05b88d0c7285f2d78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
mem2array returns a Tcl (associative) array and so the order of elements
is not guaranteed. Treat it as such.
Change-Id: Ie4d1219faac1e60247ca13bc2eedf22041a9a9e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4487
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
ctrl-z usage is incorrectly commented as ctrl-d
Change-Id: I54fe1775760ee984154bbae380baa38bcaffa04e
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Setting of flash_sector::is_erased in flash erase and mass erase
is popular folklore. Make clear it is useless.
Change-Id: Ide397eb6d24fc8fa38931e6c8a0693d39668a5d2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4768
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
The TCL command exit is already replaced by the OpenOCD command
exit in server/telnet_server.c, no need to redefine it in the
script.
Moreover, the implementation is broken because the proc ocd_throw
has been removed in mid 2008 with pre-git-era commit dfbb9f3e89
in svn rev 849.
Remove completely the unused proc exit.
Change-Id: I0365d740eccc47631eb459aab77b865b0877c1f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4986
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Depending on how the MMU is configured it is possible to have a 1:1
mapping between virtual and physical addresses, thus making this warning
bogus. We already check that the MMU is enabled in the caller:
cortex_a_virt2phys().
Change-Id: I09f4c53ef933c8d1e268da5215a769449be014bc
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5007
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Remove the target halted check from cortex_m_remove_breakpoint()
as there is no such check in cortex_m_set_breakpoint() and bp can be
safely removed from the running target.
While on it return the error code from cortex_m_unset_breakpoint()
to higher level.
Change-Id: I2b358c3661feed84297913e9f589bdf1e4de7e64
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4887
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
fp_code_available looses sync with the real number of free comparators
as soon as cortex_m_set_breakpoint() returns an error. Remove the counter
and always go through the fp_comparator_list to find a free one.
Change-Id: I9f6e06c36d8a57ad11df5155e8a1a3aff6d833a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4870
Tested-by: jenkins
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Cortex-M uses only 2 byte breakpoint instruction.
cortex_m_unset_breakpoint() does not need to check breakpoint->length,
use the length as the size argument in target_write_memory()
Change-Id: I20bb869f6abce2fc61f0469e34a638bc4dc6f7ce
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4889
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Instances of struct flash_driver are never written to at runtime. For a
small amount of memory saving and also robustness (fewer things for
stray pointer writes to hit), mark them const.
Change-Id: Iadbbbc2fac0976d892699200000c5f02856729f3
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4803
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The code for this command is currently replicated in cortex_a and
in mips_m4k and is going to be added again for cortex_m.
Plus, it is going to be obsoleted by the HW thread pseudo RTOS.
Consolidate in smp.c a single instance of the command. This will
simplify both obsoleting it and adding it to cortex_m, whatever
change comes first.
Change-Id: I03cd857e21fa3f7202fdcee36bcbd5aae30a609d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4991
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The imx8m also has a Cortex m4 so add a target for it.
Change-Id: I2abf62b6232c547fe9b12507f459835b11c63a6d
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-on: http://openocd.zylin.com/4501
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use target_addr_t exclusively for comparison of sector boudaries and
address range.
Use the last addres for both address range end and sector end.
It avoids problems with a flash bank mapped at the very end of
target address space.
Change-Id: Idf97c837453d97cbc4cf8a1c76ad799f4142f19e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4985
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This represents months of continuing RISC-V work, with too many changes
to list individually. Some improvements:
* Fixed memory leaks.
* Better handling of dbus timeouts.
* Add `riscv expose_custom` command.
* Somewhat deal with cache coherency.
* Deal with more timeouts during block memory accesses.
* Basic debug compliance test.
* Tell gdb which watchpoint hit.
* SMP support for use with -rtos hwthread
* Add `riscv set_ir`
Change-Id: Ica507ee2a57eaf51b578ab1d9b7de71512fdf47f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4922
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Some boards require a slower clock speed because of passive components on the
JTAG/SWD lines. The previous implementation would first try to discover the
chips on the default speed, and only after discovery switch to the requested
adapter_khz speed.
This patch moves the speed change to just before entering the SWD/JTAG mode,
which should alleviate this problem.
Tested on an STLink V2 clone.
Change-Id: I9734452dcc8bb28d6629e64d9a7e32ef92868cf9
Signed-off-by: Frans-Willem Hardijzer <fw@hardijzer.nl>
Reviewed-on: http://openocd.zylin.com/4818
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These macros are missing parenthesis around the argument, which can
lead to side effects, add them. Replace the argument name to avoid
conflict with uint32_t data type, since the macro can be applied to
other data types as well.
Change-Id: I32d2ffec6c062795d7c8bb23d1dfa3378bfc3a58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4994
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Bit 4 in OPTSR is IWDG1_SW (the code originally called it IWDG1_HW, but
the reference manual refers to it as IWDG1_SW). This is broken out into
a separate variable, independent_watchdog_selection, in stm32x_options.
However, this is not necessary: bit 4 is included in the user_options
field, which includes all of bits 2 through 7, and
independent_watchdog_selection is not referenced anywhere else. Delete
the field and just rely on user_options to transport that bit, along
with all the other bits it contains, between stm32x_read_options and
stm32x_write_options.
Change-Id: I4da63df9272cf091267b956c412b95671ea1d3c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4744
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Write to register DP_SELECT can fail, but both functions
swd_queue_dp_bankselect() and swd_queue_ap_bankselect() return
void and do not propagate the error.
Change the return type of the two functions to int and check the
returned value.
Invalidate the cached value of DP_SELECT if the write fails.
Change-Id: Iba6ef8b0c2332e7f7efb66337d558fb7a4a0d39c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4980
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the register DP_SELECT is written directly, e.g. with command
<dap> dpreg 8 <value>
the cached value in OpenOCD is not completely updated with the new
value, thus creating issues in the following AP and DP read/write
that rely on the cached value.
Update the cached value while writing to DP_SELECT.
Change-Id: I8221b10cd6fc1fbe73e6b834b68820b43480e1a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4979
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This should allow users to configure flash at >32-bit addresses.
Change-Id: I7c9d3c5762579011a2d9708e5317e5765349845c
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4919
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Targets can use this to expose how many address bits there are.
gdb_server uses this to send gdb the appropriate upper limit in the
memory-map. (Before this change the upper limit would only be correct
for 32-bit targets.)
Change-Id: Idb0933255ed53951fcfb05e040674bcdf19441e1
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4947
Tested-by: jenkins
Reviewed-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds "hwthread", a pseudo rtos that represents cpu cores
in an SMP system as threads to gdb. This allows to debug SMP
system kernels in a more sensible manner and removes the current
atrocities of switching gdb manually between CPU cores to update
the context.
Change-Id: Ib781c6c34097689d21d9e02011e4d74a4a742379
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3999
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
API v2 deprecates using command STLINK_DEBUG_READCOREID to read
the core ID.
Switch to STLINK_DEBUG_APIV2_READ_IDCODES on new stlink firmware
version.
Change-Id: Iabadfc116c57f2c31f08f2e77baefea0cf90bdc3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4826
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Most of ST-Link commands return an error code, but this is almost
never checked.
Check for the error code for every command that returns it.
Change-Id: Ifc4e32f8c73196de23700ba0989bfdfe0f5b46e3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4825
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
API v2 implementation for command READALLREGS returns the status
in the first two bytes, followed by two bytes of padding.
This makes the reply 4 bytes longer and changes the offset of the
first register value to 4.
Fix it for the case API v2 and clean-up the management of the
return value.
Change-Id: I448c82bcc0baa72d66fdfe7f0c525b94f8a4468b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4824
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the connection with target is lost on the physical JTAG/SWD
link (either wire disconnected or DAP/TAP in reset), STLINK fail
to connect and returns error STLINK_JTAG_GET_IDCODE_ERROR.
Add it in the list of known errors.
Change-Id: Iabd6e6892111726f614345497d9286554bfe4ac0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4982
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The new firmwares for ST-Link support handling multiple AP, but
are (actually) limited to the AP number in range [0..8].
Any tentative to operate on AP number higher than 8 returns an
error "bad AP".
Add the error code and the related message.
Change-Id: I78a98b2612d10e580d03fc43ed9f2b09619d39d8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4981
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function command_unknown() is expected to return a value
recognized as JIM error code, as it is correctly done in the
other cases it returns.
Fix the only case in which command_unknown() does not return
a JIM error code, by s/ERROR_FAIL/JIM_ERR/
Change-Id: Ib98b75755ae36870bd68c17f8839ddbfa06c6312
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4973
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix a warning identified by clang 7.0.1:
stlink_usb.c:1092:3: warning: Value stored to 'p' is never read
p += sprintf(p, "S%d", swim);
^ ~~~~~~~~~~~~~~~~~~~~~~~
Change-Id: Ic9da57e19ceecb0e3d65d3ea3412a05e1c2c779a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4945
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The null pointer used as second parameter to gdb_put_packet() is
passed as second parameter to the memcpy() in line 408 of
gdb_put_packet_inner(). In this case memcpy() does not segfault
because also the parameter length is zero. Nevertheless, the
prototype of memcpy() requires a nonnull pointer.
Fixed by passing an empty string in place of the null pointer.
Issue highlighted by clang 7.0.0 with warning message:
"Null pointer passed as an argument to a 'nonnull' parameter"
Change-Id: Ib3dde95d76fcc5fb245ee2d6669e5535d0e0b127
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4946
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- TDI/DO is not pin 2 and in fact, we don't even need to mention which
pin number it is. "TDI/DO pin" is descriptive enough.
- FT2232D link didn't work anymore. It could have been updated to the
current working FT2232D link but changed to link the FT2232H instead
which is the latest generation and the most commonly used these days.
- Taking advantage of the change, link to the MPSSE document updated.
It still worked but through a redirection, so updated just in case the
redirection stops working.
Change-Id: Ia7d01bbcac2158026831edb010a6b50f58351e42
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4908
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The command "gdb_sync" is used to resynchronize gdb with OpenOCD.
It is supposed to be follow by the gdb command "stepi" that will
be ignored by OpenOCD.
Don't annoy the user with a warning message when the stepi
command is ignored, but simply log a debug message.
Change-Id: Ie4cffa89e761d7335e5961900b62e31f209d4b1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4764
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While at it, change the macro name to make it obvious it's a string,
not some numeric ID. This also matches ARM code that's using
Change-Id: Id35ba5b95cef0ac77657c40985b24c1ae2720748
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the function aarch64_target_create() exits for an error, the
value of pointer aarch64 get lost, causing a memory leak.
Move the allocation of aarch64 after the check on the parameters.
While there, add a check on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ib9ad27f4acd940da308c01fdbf33cfe51ab0c639
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4924
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If the function mem_ap_target_create() exits for an error, the
value of pointer mem_ap get lost, causing a memory leak.
Move the allocation of mem_ap after the check on the parameters.
While there, add a check on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ia2c11b14fde9694f28bf6efe01d278923db0f0d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4923
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If the function cortex_a_target_create() or the function
cortex_r4_target_create() exit for an error, the value of pointer
cortex_a get lost, causing a memory leak.
Move the allocation of cortex_a after the check on the parameters.
While there, add checks on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ic6eeb9c3b39922d016f6d0319eada1a97a6681f0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4925
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Recent patches for STM32L4+ assumed all STM32L4 processors have a dual-
bank option. This is not the case for STM32L4{3,4,5,6}xx processors and
therefore, these processors (like STM32L433) failed when attempting to
flash the second half of the flash memory. This patch fixed this issue.
Tested on STM32L433xC, STM32L476xG and STM32L471xG.
Change-Id: I8262ba4f05190802c5868d753f3e7af50e581811
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Reviewed-on: http://openocd.zylin.com/4913
Tested-by: jenkins
Reviewed-by: Peter Tettelaar <peter@float-iot.nl>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Mark Schulte <mschulte@lyft.com>
handle_bp_command_set() showed the error message
"Failure setting breakpoint, the same address(IVA) is already used"
on any error returned from (xxx_)breakpoint_add().
Paradoxically breakpoint_add() returned ERROR_OK if it detected
duplicated bp address.
context_breakpoint_add() and hybrid_breakpoint_add() returned -1
instead of OpenOCD compatible error if they detected duplicity.
Introduce ERROR_TARGET_DUPLICATE_BREAKPOINT
Unify error handling to LOG_ERROR() any error in (xxx_)breakpoint_add()
Remove misleading error messages from handle_bp_command_set()
handle_bp_command_set() returns error if the target does not implement
add_context_breakpoint or add_hybrid_breakpoint.
Change-Id: If17dfad1756d82a77028ebdc4b305f9c8e1365ba
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4871
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Xref without trailing '.' or ',' was introduced in
deaf3d2641
Change-Id: I99afd40e1ffeddd1298b7b07e4deba3dcc41799f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4905
Tested-by: jenkins
Currently, the SWD buffer size is adjusted corresponding to the free
device memory. However, the adjusted size is not used.
This fixes SWD operations on devices with small device memory, such as
EFM32PG12 Pearl Gecko STK. It should also fix#184.
Change-Id: I2ec5cf25c62f18bd9e99a2f4aa1aa8d85ed0821b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4878
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
After commit a6c4eb0345 ("swd: Remove DAP from parameter list")
the global variable jtag_interface is not referenced in the driver.
Remove the extern declaration.
Change-Id: I72018a59c9cecaa52d9a49ec0d7816ac0e656314
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4874
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Before commit 877cec20dc ("command:
check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The commit above fixes the code in order to check the mode and
permit running the commands only if the mode is respected.
Those jim commands that have incorrect mode were not detected nor
fixes because the wrong mode was masked by the missing mode check.
After the commit above, the wrong mode triggers error in several
existing configuration scripts.
A complete list of commands that now does not run anymore as
CONFIG_ANY is reported in ticket 225, but most of them have the
mode set correctly.
At least two instances of command "jtag configure" have the wrong
mode.
Fix the mode to CONFIG_ANY for command "jtag configure" in files
src/jtag/aice/aice_transport.c and src/jtag/tcl.c
Change-Id: I3f96c5fd24d7d463712cbaf1295284fe0dc56b23
Ticket: https://sourceforge.net/p/openocd/tickets/225/
Reported-by: Bill Paul <wpaul@users.sourceforge.net>
Fixes: 877cec20dc ("command: check command mode for native jim commands")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4886
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Fix "Potential leak of memory pointed to by 'cortex_m'"
and test for NULL return from calloc in cortex_m_target_create()
Change-Id: I4d2bb5bccc57f0ed60696f3d588297a858b8ea60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4881
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added id, name, flash size and RAM size for following parts to samc20_parts[]:
SAMC20N18A
SAMC20N17A
And the following to samc21_parts[]:
SAMC21N18A
SAMC21N17A
Change-Id: Ie8cf1c531a60bfaed6e814d436d232afb89dae3f
Signed-off-by: Kevin Vermilion <kevin.vermilion@gmail.com>
Reviewed-on: http://openocd.zylin.com/4880
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix the write only out params TODO on armv7m.c
Fix conditional move depends on uninitialised value.
It was detected while programming a LPC8Nxx with a FTDI adapter.
valgrind --leak-check=full --show-leak-kinds=all --track-origins=yes
[...]
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E4D3: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E4D3: ftdi_swd_queue_cmd (ftdi.c:1206)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
==8696==
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E506: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E506: ftdi_swd_queue_cmd (ftdi.c:1207)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
Change-Id: I50f9a8c4516b686cf62ac3c76f47c53465e949da
Signed-off-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-on: http://openocd.zylin.com/4811
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Adds ability to change the user data in STM32F1x/STM32F3x MCU's option byte.
Since OpenOCD prints the content of user data in option byte registers, it
is seems logical to also provide a way how to change this data.
Change-Id: Ie6cb756b4f11b5c6dabd34bc89434a358eb758ff
Signed-off-by: Jan Vojtech <honza.vojtech@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4663
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Without this change xxx_start_algorithm() writes all register
parameters no matter of their direction. It usually results
in writing of uninitialized reg_params[].value - possibly
reported by valgrind.
While on it fix the wrong parameter direction in
kinetis_disable_wdog_algo(). This bug did not have any
impact because of unconditional write of reg_params.
Change-Id: Ia9c6a7b37f77d5eb6e5f5463012dddd50471742b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4813
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The comment above the function is correct, but the code set
the GPIO with wrong (reversed) polarity.
Change-Id: Ifd09688150d3d2018af73521e0da3926bb1b7f84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4847
Tested-by: jenkins
Reviewed-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With this patch drivers will be able to use usb path filtering.
The path format is identical to the format provided by linux kernel:
bus-port.port....
With this format it should be easier just to copy and paste
path found in dmesg.
Change-Id: I8bafa6fcb7a66ff68cc961a376f97f4f3dee35aa
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4580
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
stm32x_write_options() uses stm32x_write_block() at STM32_OB_RDP address.
The change eliminates subtracting bank->base (and later adding it back).
Change-Id: Icdd24afc7178b814be58e6033d4b93fdfb2d2a16
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4859
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Stepping in the maskisr auto mode sets breakpoint to step over interrupt
service tasks. If the device has FPB rev 1, setting hard breakpoint
is impossible on address over 0x1fffffff.
Use soft type breakpoint for adresses over 0x1fffffff if FPB is rev 1.
This may eventually fail if the code memory is not writeable, but there
is nothing to do in such case.
Change-Id: Ibdeeb506903a35d550b64f82c24c37a668de62b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4857
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
samr34/r35 combine SAML21 and SX1276 (lora transceiver). This one was found on
xplaned pro evaluation kit. Ids for other r34/r35 chips are apparently not yet
documented.
Change-Id: I4054dd56ea53c9bae8d17abd5a3e4e65e1b9c8b1
Signed-off-by: Guillaume Revaillot <g.revaillot@gmail.com>
Reviewed-on: http://openocd.zylin.com/4872
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The functions dap_to_jtag() and dap_to_swd() have been introduced by
3ef9beb52c ("ADIv5 DAP ops switching to JTAG or SWD modes") in
arm_adi_v5.c by using the JTAG queue only.
Later, in 6f8b8593d6 ("ADIv5 transport support moves to separate
files") the functions has been moved in adi_v5_swd.c and adi_v5_jtag.c
but keeping the dependency from JTAG queue.
The functions does not work if the current transport is not JTAG.
Move back the functions in arm_adi_v5.c, replace the input parameter
"target" with "dap", use the transport to detect if the JTAG queue is
present, in case of SWD transport use the proper method, for other
transports report error.
Reuse the ADI v5 sequences already present in jtag/swd.h.
Also, OpenOCD does not support switching to another transport after
the initial selection, so do not change DAP's ops vector.
Change-Id: Ib681fbaa60cb342f732bc831eb92de25afa4e4db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4852
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
A target created after init lacks target_init_one() call
and is not added to gdb targets.
Steps to reproduce:
- start OpenOCD with a dap target
- connect by telnet
target create ap0.mem mem_ap -dap $_CHIPNAME.dap -ap-num 0
reset
Segmentation fault is rised because target->check_reset is NULL.
Change-Id: I2a62f3b450e4db3005c7041a22fb8f952e68c3b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4842
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command mode was checked only for simple type of commands.
Native commands (handled by jim_handler) was treated as
they had mode COMMAND_ANY
Change-Id: Iab1d8cbb0b8c6f6b9f3cf942600432dec9a703ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4841
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 44009186cf added logging
of failed cmd name but it used c->name only. It might be confusing:
Debug: 244 105 command.c:644 run_command(): Command 'init' failed with error
code -4
User : 245 106 command.c:711 command_run_line():
Debug: 246 107 command.c:644 run_command(): Command 'init' failed with error
code -4
The command on line 244 is 'dap init'
Use full name of cmd including parents.
Change-Id: Iff131ce6454ef70b353ce1bc6d0a480b92820545
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4837
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
All the commands in OpenOCD have been inspected and have the
command mode initialize, apart for two of them.
This is not critical, because the uninitialized value (0) is
equivalent to the enum COMMAND_EXEC, that is also the correct
value for the two mentioned commands.
To keep the code consistent, initialize the command mode to
COMMAND_EXEC.
Change-Id: Iaf043364cbd1005418d787ed045a3ec653612382
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The original script was broken by changes to the Cortex-A code. The
recent introduction of the mem_ap target provided a new mechanism to
allow the script to be fixed. This also adds an example board script
for the ADSP-SC584-EZBRD.
Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While connecting under reset, use the already defined macro
SWJ_PIN_SRST to assert the srst pin.
Change-Id: Icebed462c0fe8f8c15f6522dc56625aa580b8858
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4846
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add RTOS task awareness for Chromium-EC. Currently
only supports ARM Cortex-M0/M3/M4 based targets.
No new Clang Analyzer warnings.
Change-Id: Iea56fcb1be220e2437613922879b63d6e553703d
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4685
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The xilinx_ultrascale.cfg target is actually the configuration for a
ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad
core A53. Update the filename/comments to reflect this, and include
the tap IDs for all known FPGA cores for this part.
Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4850
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The encoding of BKPT instruction is 0xE12###7#, where the four '#'
characters should be replaced by the 16 bits immediate value.
The macro uses an incorrect shift amount, thus the immediate value
is not properly coded and bits 20~23 of the opcode could get
corrupted.
Fixed by using the proper shift amount.
Change-Id: I32db8224ab57aad6d3b002f92f9f259056593675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4854
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Fix the SWD line reset sequence accordingly to Arm specification IHI
0031E that requires at least 2 idle clocks after the 50 clocks with
SWDIO high.
Fix the value of the activation code in the (currently unused)
sequence dormant-to-SWD.
Make each sequence's length multiple of 8, so it is compatible with
adapters that have such limitation (e.g. buspirate) and try to split
and comment each part of the sequence (when possible keep each part
byte aligned, inspired from commit 3ef9beb52c). This slightly
increases the sequence length but does not impact run-time
performance because these are rarely used sequences.
Add the missing sequence dormant-to-JTAG and JTAG-to-dormant, not
used yet.
On devices that implements the dormant state, IHI 0031E deprecates
the direct switching between SWD and JTAG, and recommends using a
transition through dormant. This is not implemented.
Change-Id: Iad18c0e736cfd9366be175d22658d664b0c61eab
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4851
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This hardware id is e.g. used by the Insight SiP ISP1507-AX.
Change-Id: I82568d292f9882372ab061d8e3e36906b0cc5882
Signed-off-by: Mirko Vogt <mirko.vogt@sensorberg.com>
Reviewed-on: http://openocd.zylin.com/4845
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This patch covers the fact that cortex_m could be resumed externally by
Cross Trigger Interface or by direct write to DHSCR ...
To reproduce:
- halt the target
- then run the core through DHCSR (mww 0xe000edf0 0xa05f0001)
=> this resumes the core, but target state in OpenOCD remains HALTED.
Change-Id: Ifa1ae18645bfeb863acc78a039bbf04873fd78fe
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4817
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex_a_debug_entry and update_halt_gdb are called in two consecutive
conditions which are complementary, so externalizing the common code
makes the conditions' body lighter
With the removal of LOG_DEBUG(" ") since it does not look too informative
Change-Id: I0c54e413619576bb3af164f2dcf256c5a862c5fd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4832
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
If malloc fails in __command_name, the following strcpy will
segfault, thus preventing __command_name to return.
The actual calls to command_name() implement the correct check
for the NULL pointer, but propagate error -ENOMEM, that is not
an error value coherent within OpenOCD. Plus, in one case it
overwrites an already detected error.
Check the pointer returned by malloc and, in case of failure,
issue an error message and return the NULL pointer.
Let the caller of command_name() to keep the already detected
error or to return ERROR_FAIL in case of end of memory.
Change-Id: I151a24569409777dd5bc09a3daf5dba2b8e2829b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4838
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio.
Change-Id: If5b3c618097b71dfe7fcf988fb3c1499ae03a6d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4833
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Valgrind and Clang Static Analyzer have no complaints about this change.
Change-Id: I7757615ec52448372bdc57729cdf97c7016d97e8
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4656
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commands to stlink devices are typically comprised of multiple
transactions with each transaction completing before moving to the next.
This change allows for multiple USB transactions to be issued at once
followed by a check that all transactions completed successfully. This
improves performance on some machines where there is a large turn-around
time between USB transfers such as is seen on some virtual machines.
This change is only supported when compiled with libusb1 as libusb1
supports and asynchronous interface.
Multi-transaction queueing introduced in this change paves the way for
improving speed of other transactions in the future such as memory and
register reads where multiple USB transactions in succession are
required to complete a command. Multiple USB transactions can be
submitted at once using jtag_libusb_bulk_transfer_n function.
Change-Id: I924e049217a789ef445b14e00aa1983576970fbf
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4484
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When few adapters of the same type are in use, the serial string is
the way to select the right one.
Currently a serial string that does not match any of the connected
adapters will just fail the open, without specific information to
track the issue.
Add a specific message to highlight that the open failure is caused
by a serial mismatch.
Change-Id: I5cb77f1045cc746e532d395b2e5ced40a23ab638
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4701
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d1b7437633 fixes libusb1 to
return OpenOCD error values instead of negative errors in Linux
kernel's style.
The same fix should be applied to libusb0 too.
Fix return value of libusb0 to uniform it to OpenOCD style.
Change-Id: I68478c29c91c6be720074f58c432fe51477e03ed
Fixes: d1b7437633 ("libusb: return oocd error values")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4698
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
aarch64-linux-gnu-gdb 8.2 uses "aarch64" as default architecture,
but also supports the value "aarch64:ilp32" and all the values
supported by arm-none-eabi-gdb.
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for aarch64 target to "aarch64".
Change-Id: I63e9769f47d8e73f048eb84fa73e082dd1c8e52c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4755
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
arm-none-eabi-gdb 8.2 uses "arm" as default architecture, but also
supports the following values: "arm_any", "armv2", "armv2a",
"armv3", "armv3m", "armv4", "armv4t", "armv5", "armv5t", "armv5te",
"armv5tej", "armv6", "armv6k", "armv6kz", "armv6-m", "armv6s-m",
"armv6t2", "armv7", "armv7e-m", "armv8-a", "armv8-m.base",
"armv8-m.main", "armv8-r", "ep9312", "iwmmxt", "iwmmxt2", "xscale".
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for all arm targets to "arm".
Change-Id: I176cb89878606e1febd546ce26543b3e7849500a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4754
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
The gdb patches for stm8 are still not merged in the official
repository and are temporarily hosted in
https://stm8-binutils-gdb.sourceforge.io/
The latest patch set
stm8-binutils-gdb-sources-2018-03-04.tar.gz
define only one possible value ("stm8") for this architecture; it
can be displayed typing "set architecture " followed by a TAB for
autocompletion in gdb for stm8.
Set the gdb architecture value for stm8 to "stm8".
Change-Id: I643ceba662de46cecf061d1dc672b9178a077f1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4753
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
xPSR.T sets the processor to Thumb mode when set to 1. ARMv7-M only
supports execution of Thumb instructions, so it must always be set to 1.
If xPSR.T is set to 0 on armv7m, a usage fault is generated when a
instruction execution is attempted.
On armv7m, issuing a reset causes the vector table to be examined. PC
and xPSR.T are loaded from the vector table at byte offset 4. xPSR.T is
taken from the least significant bit this value, PC from the remaining
bits. This occurs even with `reset halt`, as the reset itself causes
this load to occur without the execution of any instructions.
As a result of this, following a reset with a "bad" value programmed in
the vector table, openocd would be unable to run algorithms on the
target, as running them would immediately result in a usage fault due to
xPSR.T being unset (0).
Allow algorithms to run regardless of the content of the vector table by
explicitly setting xPSR so that xPSR.T=1 prior to executing an
algorithm. One can think of this as openocd more closely emulating a
reset or branch instruction in executing it's algorithms.
Ticket: https://sourceforge.net/p/openocd/tickets/203/
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: I4dc3427ab195d06c3fd780ea768027fefccc4c28
Reviewed-on: http://openocd.zylin.com/4658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XDS110 stand-alone version has the ability to supply
voltage to the target board via it's AUX FUNCTIONS port.
Added command to enable setting the voltage on the XDS110
stand-alone.
Change-Id: I2f21c4a3d15ed99e649f3a83973c5e724c4bfeb6
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4793
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The fact that one needs to always push contributions to a single
remote reference (refs/for/master) might seem odd to people unfamiliar
with Gerrit. GitHub, for instance, hosts personal repositories where
developers typically create topic branches for each contribution and
use a proprietary mecanism to request a review (the "pull request").
More generally, one normally does not expect to be able to push
non-fast-forwarding stuff to a remote branch.
This commit adds a clarifying note to the patch guidelines.
Change-Id: Ia750b815b82b18e92b6109c07f451000dcbecf9b
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-on: http://openocd.zylin.com/4806
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Longest erase all FLASH for nRF5 series is 295.3 ms for nRF52832.
Timeout period now is set to 340 ms (295.3 + 15%)
Change-Id: Iae00ed7b634f111b9798db11e35e4e066d4aaa95
Signed-off-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-on: http://openocd.zylin.com/4822
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target configure -work-area-xxx calls target_free_all_working_areas()
and sets the desired new parameter. Without this change the working area
does not get reallocated if it has been allocated before.
target_free_all_working_areas() results in work area containing one block
marked as free.
Completely free working area in target_free_all_working_areas()
Change-Id: I79c681082f32f2a96a2b40eb3b8751e427549693
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4797
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The block of code moved without any changes
Change-Id: I70b82dc3315dcc3f34de0537b362bee230007d02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove option 'srst' which is not recognized from on-line help and texi.
Check parameter and return syntax error if wrong option is entered.
Change-Id: I87daa423a9f53193a0b015080594820b933628f5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4795
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Cortex-M0, M0+ and M1 do not support VECTRESET bit in AIRCR.
Without this change the 'reset' command silently fails if VECTRESET
is requested.
Detect these cores, show warning if VECTRESET is about to use
and use SYSRESETREQ instead.
Change-Id: Ief174373e3ef0e6b287c57911c0aca4dfa8209f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4794
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds TARGET_HALTED check in armv8_get_core_reg32()
and armv8_set_core_reg32() to void a crash issue when gdb connects
but fails to halt the ARM core. Similar logic can be found in
armv8_get_core_reg() and armv8_set_core_reg().
Below is the call stack information of this case when gdb connects.
(gdb) bt
regnum=regnum@entry=0, dpm=0x990110) at src/target/armv8_dpm.c:657
r=0x9c7240, regnum=0, mode=<optimized out>) at src/target/armv8_dpm.c:974
at src/target/armv8.c:1487
packet=0x8ec8e0 <gdb_packet_buffer.9962> "g",
packet_size=<optimized out>, connection=<optimized out>)
at src/server/gdb_server.c:1200
at src/server/gdb_server.c:3180
command_context=command_context@entry=0x935010)
at src/server/server.c:566
...
Change-Id: I159837b533f110998184f910a0abe48409bd58f1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/4758
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Arm architecture reference manual DDI0406C reports at page 2024 in
table C3-1 the processor behaviour on debug events depending on
the debug-mode (none, monitor or halt), mode selected through the
bits MDBGen and HDBGen in DSCR register.
The halt request is served independently from the debug-mode. Thus
it's useless to enable the halt debug-mode in cortex_a_halt() by
setting the bit HDBGen (macro DSCR_HALT_DBG_MODE).
On the other side, halting for a breakpoint, a watchpoint or a
vector catch requires being in halt debug-mode.
Today HDBGen is set only in cortex_a_halt(), so we are forced to
halt the core at least once before it can be halted for hitting a
breakpoint/watchpoint/vector-catch. This is annoying since there
is no need to halt the target to set a HW breakpoint.
Move in cortex_a_init_debug_access() the selection of the halt
debug-mode, so the mode is set during examine.
To prevent a misconfigured hardware breakpoint/watchpoint/vector
catch to halt the target when OpenOCD has already quit, return to
debug-mode none at OpenOCD exit.
Change-Id: I68a1c51de3572ca1b89e90caf7eb20374268e926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4783
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
DEBUG_WAIT is useful to debug adi_jtag issue,
and the WCR register is replaced by DLCR for DP registers update
in commit 150b7d26f2.
Change-Id: I3faa9ea8a6adacd3d5275e40382801da731db32f
Signed-off-by: YanLin Zhu <zhuyanlin@pinecone.net>
Reviewed-on: http://openocd.zylin.com/4804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
The OpenOCD commands that have been wrapped with 'ocd_bouncer' are
executed within two levels of nested proc's:
# see register_command_handler() in src/helper/command.c
proc my_command {args} {eval ocd_bouncer my_command $args}
# see ocd_bouncer in src/helper/startup.tcl
proc ocd_bouncer {name args} {
... [eval ocd_my_command $args] ...
}
This causes the stack frame of 'ocd_my_command' to be the same one
of proc 'ocd_bouncer', thus two levels below the stack frame of the
caller of 'my_command'. This is an issue with commands that receive
a variable by name and have to resolve them to access the value.
E.g. the command
<target> mem2array arrayname bitwidth address count
is wrapped; it receives the name of the array but fails to resolve
it in the current stack frame. Instead, the commands
mem2array arrayname bitwidth address count
ocd_<target> mem2array arrayname bitwidth address count
are not wrapped and can directly access the array because they share
the same stack frame of the caller.
Same situation with the symmetric commands 'array2mem'.
How to test:
within a telnet connection, run the following set of commands,
eventually replacing the address 0x08000000 with a valid readable
address of your <target>,
unset -nocomplain v1 v2 v3
info vars v?
mem2array v1 32 0x08000000 1
<target> mem2array v2 32 0x08000000 1
ocd_<target> mem2array v3 32 0x08000000 1
info vars v?
and notice that only v1 and v3 are now allocated. The array v2 has
been allocated in the temporarily stack frame of proc ocd_bouncer,
together with its local variables, and then lost when proc ended.
Fixed by executing the wrapped commands with the command 'uplevel'
instead of 'eval'. The amount of levels to skip is checked to avoid
errors in the unusual case 'ocd_bouncer' is called directly without
the first level of wrapper.
Change-Id: Iff90fb8921faf9b5ab04f61062a530578cc20d78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4731
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Slow version of blank check procedure reads target memory sector-by-sector
using 1 KB chunks. Due to bug in chunk size calculation algorithm the actual
size of the chunk is always 1 KB even if sector size is smaller.
This causes out-of-boundary read of the last sector.
Steps to reproduce:
1) Use target with small sectors (e.g. psoc6 with 512-byte sectors)
2) set WORKAREASIZE_CM0 0
3) flash erase_check 1
Running slow fallback erase check - add working memory
Info : SWD DPIDR 0x6ba02477
Error: Failed to read memory at 0x14008000
unknown error when checking erase state of flash bank #1 at 0x14000000
Bank is erased
Change-Id: I03d0d5fb3a1950ae6aac425f5e24c7fd94b38325
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4785
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch removes use of register write protection in protect() and
protect_check() now that Change 4765 has merged.
Change-Id: I42c429dc283c5b53989a6b98ebfc58214274ff16
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4791
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for instruction tracing to eSi-RISC targets. The
command interface is borrowed heavily from ETM; eSi-Trace uses a less
sophisticated model for tracing, however the setup and usage is similar.
This patch also cleans up the command interfaces of the other esirisc
command groups and adds additional debugging information to log messages
when dealing with CSRs.
This patch "finalizes" support for 32-bit eSi-RISC targets.
Change-Id: Ia2a9de79a3c7c066240b5212721fb1b7584a9a45
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4780
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
original CC3200 launchpad works only with ti-icdi driver
which stopped to work after merging to master commit
d02de3a8a9
Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When GDB analyses the status of the target it try to guess the
current stack frame and issues few memory read.
E.g. on ARM targets GDB uses R11 value as a potential frame-pointer
and reads at the address pointed by R11.
The address of such memory read is not always valid and can trigger
an address translation failure.
Replace LOG_ERROR with LOG_WARNING in case the virtual address does
not have a hit in TTB; print the virtual address in the warning
message and discriminate the two identical messages with [1]/[2].
Change-Id: I288b8cd26bec2543c4f1c16b7c06dc47d5d843d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4602
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For compatibility with libusb1, define LIBUSB_TRANSFER_TYPE_BULK
in libusb0.
Remove the #ifdef HAVE_LIBUSB1 in jtag/driver/aice
This also fixes a compile error in jtag/drivers/openjtag with
libusb0.
Change-Id: I827b77eac10216759eb31aab461b2b63cabaf195
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4700
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updates support for L4+ device id: 0x470 added by #4310
Extends #4641 to account for L4+ use of multiple DBANK option bits
Enables L4+ 1M and 2M devices to be programmed using sector erase
Change-Id: I42bb379d7d97986f4506423e3da503d07c787c6b
Signed-off-by: bob <rea952@gmail.com>
Reviewed-on: http://openocd.zylin.com/4777
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove inappropriate use of bank_number.
Change-Id: I11be1f2540cb09a3ccede35312f90bc8276af338
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4788
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit f1be0e6af2 ("HELPER/LOG:
review unused symbols") removed a set of unused functions and,
as consequence, there is no code anymore that sets the variable
"log_forward_count". But, the commit above did not removed the
code (now dead) that depends on "log_forward_count" set.
Remove the code dependant on "log_forward_count" set and the
variable itself.
Change-Id: I6efe93d1dccbe13c409c5bc55ba47a2684c0e3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Handy to test vendor commands in a CMSIS-DAP adapter.
Change-Id: Ieeaa276edf770b1a3076a186e9056b4e5180362a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3103
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
The ST-LINK/V2.1 embedded in the new nucleo boards for STM8 does
not follow the normal versioning rules, and puts mass-storage and
swim version in the field normally used respectively for jtag and
mass-storage version.
Apply the check suggested by STMicroelectronics to discriminate
the two cases and print the correct version.
Change-Id: I0dd1da11013be3f1e56084489e28cfba98bb07af
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4716
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Starting from stlink V2J15 the API
STLINK_DEBUG_APIV2_GETLASTRWSTATUS
is obsoleted and replaced by the new API
STLINK_DEBUG_APIV2_GETLASTRWSTATUS2.
Manage the two cases to be prepared for an eventual future
removal of the obsolete API.
Change-Id: Ic4498a652865b2eb6148825138c2f6855a06ba47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4714
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Until version J14 the behaviour of ST-Link was to send a reset
pulse to the target when the debug connection is started in JTAG
mode. No reset pulse is sent, instead, in SWD mode.
Version J15 introduces a new parameter to avoid the reset pulse in
JTAG mode, aligning the behaviour with SWD.
This reset from the ST-Link, if propagated to the target, prevents
attaching a running target.
Actually this reset pulse is very short (few microsecond) and can
be easily filtered out by an on-board capacitor, usually present
on the reset wire (mainly to filter the bounces of the reset
button). Moreover, most of the use cases for ST-Link are with SWD
(not with JTAG) and this has probably further masked this JTAG
specific behaviour.
OpenOCD can tolerate it but requires the flag "connect_assert_srst"
to the command "reset_config", but the flag is not present in any
configurations in folder tcl. This enforces the guess it was not
noticed due to on-board capacitors or missing connection of reset
pin or ST-Link only used in SWD; so it's safe applying this patch.
Change the default behaviour to avoid reset in JTAG at connection.
There is no need to manage the ST-Link version here, since every
parameter that is not recognized by older ST-Link is treated as
"connect in JTAG with reset pulse", keeping backward compatibility.
Change-Id: Idc97a1457279e3970fd0839cadbff22d9b0302d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4713
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The API version is hardcoded in the STLINK device and depends on
the specific firmware version. There is no way to switch between
different API. Thus, it make no sense to keep in two separate
variables the current and the max API supported because they are
always equal to "the only" API supported by the specific STLINK.
Collapse h->version.jtag_api_max and h->jtag_api in a single
variable h->version.jtag_api
Remove an extra print of api version; this is already advertised
while printing the STLINK version.
Change-Id: I0519694a34748e5a0aa330932c1256080a6d5f20
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4712
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fix the condition for ST-Link/V1; it does not support trace.
Trace is added on ST-Link/V2 and ST-Link/V2.1 only.
Change-Id: I17416edd05a2c8ece605560b7533edac4f982cfc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4707
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The number of stlink firmware version is growing, each carrying new
features. Today's code has several check distributed here and there
and it's already hard to track them and verify the correctness.
The introduction of STLINK-V3 will make the situation much worst,
and the code much less readable.
Add a "flags" bitmask in the struct stlink_usb_version to allow
setting individual bits for each feature available or for specific
quirks and workarounds.
This patch does not implement setting nor testing "flags"; it would
be introduced in following patches, one bit at a time.
Change-Id: I09d78202646a6c8330731f8aa96dc9d295fa5655
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4706
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The old ST-Link/V1 can either run an obsolete firmware with API_V1 or
a more recent firmware (from V1J11 to last V1J13) with API_V2.
SWD is only provided by the latter API.
Return error is SWD is selected on adapters that does not support it.
Change-Id: Iac4ba54d191ba80fb445a7cd3d8c2621dc7a4846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4705
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Recent stlink version V2J26 introduces support for 16 bit memory
read/write.
Add the new API and modify the wrappers stlink_usb_{read|write}_mem
For older version of stlink keep the same behavior as in current
code.
While there, fix some minor typo in comments inside the wrappers.
This fixes ticket #204 ("st-link can't flash stm32f2x based flash
without target algorithms").
Change-Id: Id7d404e588f10a4b0f8a93d7ca44cef8e4c49b4f
Author: Laurent LEMELE <laurent.lemele@st.com>
Rebased-by: Antonio Borneo <borneo.antonio@gmail.com>
Ticket: https://sourceforge.net/p/openocd/tickets/204/
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4704
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
ST-Link uses two separate API for setting the interface speed in SWD
and JTAG.
Add the missing API for JTAG and run the proper API depending on the
selected mode.
Change-Id: I71e955e23c1d82c2ea1c8bfade7612c5a0377a74
Author: Laurent LEMELE <laurent.lemele@st.com>
Rebased-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4703
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The original code was written for and tested on little-endian
host only.
Rewrite it to be independent by host endianess.
Not tested on real HW; I don't own anymore a SPEAr device.
Change-Id: I2f427a804693f56cb9dea4936c525eb814c48c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4778
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for reading halfword values from memory. This
command compliments existing support for writing halfwords (mwh).
Change-Id: I8ec628e65c05a7f00aa57e3af0f228eb8bd4d14e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4781
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
FT232R: introducing configurable parameters for pinout,
initial buffer size, state of RS232 signals at exit with
option to reattach kernel driver. All this was hardcoded before.
New parameters are documented in "openocd.texi" file.
Allows hopfully self-explainable and user-friendly adaptation to
various pinouts and similar chips like FT230X and FT231X.
Change-Id: Ib807f2ea3d4c1a164d351d65aeacd1978318d217
Signed-off-by: EMARD <vordah@gmail.com>
Reviewed-on: http://openocd.zylin.com/4681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some flash drivers had a dummy method for erase_check.
Use default_flash_blank_check() instead if possible.
Change-Id: Iddfeff45ce477007328d061fcb5c553d93c3be98
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4766
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
read_cmd, qread_cmd, pprog_cmd added as some recent high densities devices
use variants for 4-byte addressing.
Some new flash and FRAM device ids added. FRAMs don't have write pages nor
erase commands or sector sizes. The corresponding entries are marked as
"not used" (i. e. zero). Checks in existing SPI flash drivers added to
handle these cases gracefully.
Change-Id: I5104bce7c815ac22f98bc32c1bb6db66b984404a
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4773
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This increases performance drematically for local connections, which is the
most likely arrangement for a VPI connection.
Change-Id: Id15b29ae663f5d8100b2175357649bd03d05b7c8
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4549
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make flash_driver methods protect() and protect_check()
optional.
Remove dummy definitions of these methods from the drivers
which do not implement protection handling.
Some drivers did not define protect method. It raised segfault
before this change and now it is handled properly.
Lot of drivers returned ERROR_OK from dummy protect()
- now flash_driver_protect() returns an error if not handled by the driver.
Change-Id: I2d4a0da316bf03c6379791b1b1c6198fbf22e66c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4765
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Since commit bae76053dc
gdb-attach event is defined as halt by default.
Remove useless and in case of bcm281xx wrong definitions of the event.
Change-Id: I8e69780a93722eb9392673303f54d502e71eceb6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4763
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
The dual bank option was being incorrectly read and the
bank b base incorrectly set. This is tested with 512kB
dual bank configuration but needs checking with other
configurations (e.g. 256kb).
This fix should remove the need to use a mass_erase command
prior to programming with OpenOCD
Change-Id: I6e920f11b794c4c1fd34c0e44fb8fa01e7fe8f85
Signed-off-by: Alex J Lennon <alex.lennon@s19.tech>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4641
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Thomas Søhus <soehus@gmail.com>
Prepare for additional flash banks not located at address 0
Change-Id: I60b78c917f94fa52bf24df9e3315536f776eec84
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-on: http://openocd.zylin.com/4440
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
S6 record is equivalent to S5 but it uses 24-bit value (instead of 16-bit)
to store total number of data records. It can be found in big srec files
with total number of data records bigger than 65535
Handle S6 record in the same way as S5 (simply ignore it)
Change-Id: I3e15a4e8f784fd38803c00accf422f803e8469cd
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4645
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The reset_config line in the config file does not actually set
connect_assert_srst (the default is connect_deassert_srst), but it reads
as if it does. Clarify that the target is compatible with
connect_assert_srst, without suggesting that the file actually sets it
to that value.
Change-Id: I14e9445ab282d386b5d0055f6adf03d7c8878a8c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4743
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In previous versions of OpenOCD, it was possible to connect to the TCL
RPC interface without a current target. In `tcl_new_connection`, the
curent target would be queried by number, and the possibility of a null
current target was handled properly.
In commit bb9d9c6026, the
`get_target_by_num` call was replaced by a `get_current_target` call,
without noticing that `get_current_target` aborts if there is no current
target, whereas `tcl_new_connection` is perfectly able to handle that
situation.
Provide a `get_current_target_or_null` function for use by consumers who
are OK with a null current target, and use it in `tcl_new_connection`.
Change-Id: I06f7e1e149f1169e23c73ba328c7ad9f9425cc2a
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4730
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The for loop inside bitq_path_move function is not correct, this will
overflow the cmd->path array and produces an unpredictable result.
Change-Id: I81e3bc9ee6d1dd948acd2fe4c667103ac22bb26f
Signed-off-by: xuguangxiao <szgxxu@qq.com>
Reviewed-on: http://openocd.zylin.com/4733
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The functions cortex_a_dap_{read,write}_coreregister_u32() are
duplicate of the functions dpm_{read,write}_reg().
Remove both duplicated functions in cortex_a.c while export only
dpm_read_reg(), since dpm_write_reg() is currently not used.
Rename dpm_read_reg() as arm_dpm_read_reg() to keep uniform the
naming style.
Change-Id: I501bc99dc402039e630c47917a086a0bb382782c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4747
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
The name of the function dpm_modeswitch() does not follow the
common style of the other function names in the same file.
Rename it as arm_dpm_modeswitch().
Change-Id: Idebf3c7bbddcd9b3c7b44f8d0dea1e5f7549b0eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4756
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The armv7m debug port provides a direct access to the CPU memory
bus, allowing the debugger to bypass the CPU for every memory
operation.
The armv7a debug port doesn't offer the same feature, mainly
because CPU caches and MMU makes the direct memory access more
tricky. Nevertheless most SoC with armv7a provide direct memory
access through an AHB bus available on another DAP access port,
different from the debug port.
The original port of cortex_a in OpenOCD was inspired from the
working cortex_m code, and provided optional memory access
through the AHB, if present.
The code for AHB access is problematic and partially buggy due
to incomplete management of cache coherency and missing check of
page boundary during virtual address operations.
With the commit 5d458cf727
("target/mem_ap: generic mem-ap target") we have a clean support
for memory access through system buses connected to DAP AP, which
obsoletes the buggy memory AP hack in cortex_a.
Remove any code that uses the memory AP accesses in cortex_a.
Change-Id: I7cd1f94885e5817448058953e043d8da90dea3cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4748
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The variable fast_reg_read is always zero, causing some code to
never be executed.
Such code try to read the target registers by dumping them in
memory and then reading back the memory through the debugger. But
it is broken due to lack of cache and MMU management.
This code also uses the broken memory_ap access that is going to
be removed soon.
Remove all the code that depends on fast_reg_read not zero.
Add a missing check on arm_dpm_read_current_registers() return.
Keep the unused function cortex_a_dap_write_coreregister_u32()
to balance the used "read" version.
Change-Id: If2ff28a8c49eb0a87dc85207f5431978efd158db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4746
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Handle write protection status in blocks instead of sectors, removing
unnecessary complexity in the process. Now closer to stm32f2x.
Support sequential modification of option bytes by read/modify/write
directly to option bytes area instead of always starting with the
currently loaded bytes from FLASH_OBR/WRPR registers.
Added new command 'options_load' to force re-load of option bytes w/o
having to power cycle target.
Change-Id: I5c76191e29c17a1e11482df06379d10ca8d6d04d
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4576
Tested-by: jenkins
Reviewed-by: Jan Vojtěch <honza.vojtech@gmail.com>
At OpenOCD start-up the operation of clearing the sticky error in
CTRL/STAT register ignores the current value of the power domains
bits CDBGPWRUPREQ and CSYSPWRUPREQ in the same register and
incorrectly set them to zero.
This abrupt disable does not follow the requirement in IHI0031 to
wait for the acknowledgment of power disabled before continuing.
The power domains are then re-enabled immediately after; it is
possible that such short disable period has passed undetected or
has been tested only on devices that do not implement the power
domains.
Anyway, this sequence is incorrect and can generate unexpected
and hard-to-debug issues while OpenOCD attaches to a running
target that implements power domains.
Anticipate the initialization of dap->dp_ctrl_stat and use it
while clearing the sticky bit. This has the additional effect of
avoiding a power disable in the error recovery part of the
function dap_dp_read_atomic().
Keep the same sequence of read/write in dap_dp_init() to avoid
breaking the initialization of some problematic target.
Add comments to document these choices.
Change-Id: I8d6da788f2dd11909792b5d6b69bc90fbe4df25d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4677
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
While on it correct RAM amount of SAMR21x16A devices
Change-Id: Ie9ab9de1551bdceff17af7597a9a2ee41f5aebe0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4734
Reviewed-by: Eduardo Montoya
Tested-by: jenkins
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The performance of CMSIS-DAP in long data transfers was improved substantially in
ef02b69b14. But it not as good as some
other USB/MCU based adapters. Using HID and therefore interrupt endpoint
is slower than USB bulk transfer.
CMSIS-DAP adapter implements multiple HID buffer handling and OpenOCD already
reads number of buffers from info command.
This change adds capability to sumbit more than one HID requests before
driver waits for a HID response. This scenario is used for long transfers only.
Results show about double speed on USB FS and ~140% speed on USB HS:
| w/o this change | with multi HIDrq
-----------------------------------------+-----------------+-----------------
Open source CMSIS-DAP, USB FS, adapter_khz 1000
dump_image ram32k.bin 0x1fffe000 0x8000 | 23.225 KiB/s | 45.901 KiB/s
load_image ram32k.bin 0x1fffe000 | 23.324 KiB/s | 46.552 KiB/s
Cypress' Kitprog in CMSIS-DAP mode, USB FS, adapter_khz 1000 (over firmware limit)
dump_image ram64k.bin 0x20000000 0x10000 | 15.537 KiB/s | 42.558 KiB/s
load_image ram64k.bin 0x20000000 | 15.605 KiB/s | 43.291 KiB/s
Atmel's EDBG, USB HS, adapter_khz 10000 (#3945 applied)
dump_image ram384k.bin 0x20400000 0x6000 | 248.402 KiB/s | 345.250 KiB/s
load_image ram384k.bin 0x20400000 | 256.039 KiB/s | 365.945 KiB/s
Change-Id: I9edbe018086176d357c6aaba5d6b657a5e5e1c64
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4080
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Adding the call to keep_alive() to suppress warnings when
running the async flash algorithm. Issue observed when
loading large pieces of code on slower debuggers.
Change-Id: I7660fa05f68ebd7be07b2ca0a55b0f3b6ae718f3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/4686
Tested-by: jenkins
Reviewed-by: Jesse Marroquin
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c8926d1457 introduces the
context and hybrid breakpoint types beside existing SW and HW
types. The new field "asid" is non-zero only for these new types.
The commit above did not properly initialize "asid" to 0 for a
temporarily HW breakpoint used during single step. This causes
cortex_a_unset_breakpoint() to identify this breakpoint as of
type "hybrid".
Identified through valgrind error:
Conditional jump or move depends on uninitialised value(s)
Actually valgrind triggers a total of 10 messages about use of
uninitialized variables, but they are all caused by the first
conditional jump bases on "asid != 0".
Fixed by initializing "asid" to 0 in cortex_a_step().
Fixes: c8926d1457 ("cortex_a hybrid & context breakpoints")
Change-Id: Ib674d8457d1e02e10332fd9d73554d13719ef93d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4613
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add/detect missing IDCODEs for the Spartan 7 family and Artix 25T
and Artix 12T.
Change-Id: Ib6c83c5592e90df1eb8e715e79b279da9a95f9c6
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4428
Reviewed-by: Robert Jördens
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit 0057c71ab6 updates the OpenOCD
cached values of CSW and TAR registers if these registers are modified
by an apreg command.
The condition to force the update of CSW cache is incorrect and it will
erase the default CSW value.
Moreover, calling mem_ap_setup_csw() does not honor the value requested
in the apreg command because such value is incorrectly bitwise or-ed
with csw_default.
Fix it by updating csw_value, instead of erasing csw_default, and writing
directly in CSW register the new value from the command line.
Change-Id: I40273cb64d22ccfb9b6d3499bd39b586eb60de38
Fixes: 0057c71ab6 ("target/arm_adi_v5: sync CSW and TAR cache on apreg write")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4679
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The Mimas A7 FPGA board has FTDI FT2232 whose channel B is connected to
Artix-7 FPGA's JTAG interface. Hence, OpenOCD can easily interface with
it via the its ftdi driver interface. Tested to be working great up to
30 MHz.
Change-Id: Ieda015fbc6135bf95ad5a069cbf38650da45911e
Signed-off-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-on: http://openocd.zylin.com/4720
Tested-by: jenkins
Reviewed-by: Tim "mithro" Ansell <me@mith.ro>
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some protocols make use of empty scan fields for optional padding, which
causes the log to fill with unhelpful messages that a field is empty.
The remaining LOG_DEBUG messages in ftdi_execute_scan have been demoted
to DEBUG_JTAG_IO such that these messages are only seen when debugging
JTAG.
Change-Id: I61fd4551411ce851da34e67d003bca5d7a71cd92
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4112
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch corrects a crash in uCOS-III on a new GDB connection when
RTOS autodetection is not used. The crash was caused by not checking if
the symbol list had been loaded prior to updating threads.
Change-Id: I64c5133e02fe22fc8d14584cc40d87b49c935b0b
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4719
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch makes the cmd_queue_scan_field_clone function public. This
permits targets to insert fields without affecting the submitted
scan_field list. This will be used in an upcoming target implementation
that needs to insert additional padding bits.
Change-Id: I8fbd3b9b4e413432471f4f1444048932c8fa189e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4082
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds support for p packet responses by targets configured
with RTOS support. This change required moving to a rtos_reg struct,
which is similar to struct reg used by targets, which resulted in
needing to update each stacking with register numbers. This patch also
allows targets with non-linear register numbers to function with RTOSes
as well.
Change-Id: I5b189d74110d6b6f2fa851a67ab0762ae6b1832f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4121
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch fixes a number of bugs caused by incomplete support for
non-existent registers. This is needed for targets that provide optional
registers or non-linear register numbers.
Change-Id: I216196e0051f28887a2c3da410959382369eed80
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit 5aceec2412 ("drivers:
cmsis-dap: pull up common connect code") breaks the driver and it
cannot connect anymore in JTAG mode.
The issue is caused in cmsis_dap_init() by anticipating the call to
cmsis_dap_usb_open(), which then sets cmsis_dap_handle and makes the
following test to always fail.
Actually the original code was quite tricky:
if (swd_mode)
do something that also sets cmsis_dap_handle;
if (cmsis_dap_handle == NULL)
do something for !swd_mode;
Convert the sequence of tricky "if"s in a single "if-then-else" to
handle clearly the cases swd_mode and !swd_mode.
Change-Id: I359a23bf26a3edc2461f4352daa0be83e78868f7
Fixes: 5aceec2412 ("drivers: cmsis-dap: pull up common connect code")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4697
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add configuration for the Renesas R-Car Generation 3 targets.
These are SoCs with Cortex A57s, A53s, and R7s. All cores
are supported.
Change-Id: I795233210e4f647a1a2a0adea7c058ae98b5db70
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4669
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Virtual targets, like mem_ap, do not or cannot implement the required
functionality to accept a GDB connection. In the case of mem_ap, the
method get_gdb_reg_list() is missing and a following connection from
gdb causes OpenOCD to segfault.
OpenOCD opens a GDB port for each target; it's always possible to
connect, by mistake, GDB to one virtual target.
Add a method to check if the target supports GDB connections (for the
moment just checking if get_gdb_reg_list is implemented).
Skip opening a gdb server for every targets that don't support GDB
connections.
Change-Id: Ia439a43efe1a9adbb1771cd9d252db8ffa32eb9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4676
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
No need to reboot the Linux box when new rules are added to udev.
Suggest the command in the script header.
Change-Id: Ie95383bfd73914a3d2e2c05d77fa3eb32e68b7e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4665
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The subunit of the debug unit is called the Flash Patch and Breakpoint
unit, abbreviated (by ARM no less) as FPB, not FBP.
Change-Id: Ia2f08470da705f0f1518feeca878f0f500507308
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4675
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enables the programming of Write protection lock bits.
- Updated/re-factored with option_read, option_write and option_load commands.
Change-Id: I86358c7eb1285c3c0baac1564e46da8ced5fd025
Signed-off-by: Thomas Søhus <tls@ceepro.dk>
Reviewed-on: http://openocd.zylin.com/4654
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 31c58c139d ("jtag: drivers: stlink: handle all versions with
single config") deprecates the use of "interface/stlink-v2-1.cfg" in
favor of a unique config file "interface/stlink.cfg".
Update the example in the documentation.
Change-Id: I1aed7c70e15f4edb4f81a3ee8e3bce575fde873b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4667
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The field ap_num in struct adiv5_private_config is already of type int.
Casting it to type int has no sense.
Change-Id: Ida642e808c02591bb58609425eccd096d404e2c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4666
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The periodic poll scans all the targets in the same order they
have been declared in the configuration file.
When one target in a SMP node halts, the transition is detected
in the following poll and this triggers a halt request to all the
other cores of the SMP node.
The targets that will be polled afterwards will be identified as
"halted", but the targets already scanned will remain as
"running" until the next periodic poll.
This creates a race condition with GDB; GDB sets the breakpoints
when runs the target and removes them as soon as the target is
halted. When it receives the halt event, it starts removing the
breakpoints and fails on the targets that are still reported as
"running".
Fixed by polling all the targets in the SMP node before informing
GDB about the halt event.
This implementation is almost copy/paste from the one in aarch64.
Change-Id: Id2bd99f1e56b014e48e9e34ccb891b4219c518f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4622
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
To existing <bus>:<port>,<port> format add <bus>-<port>.<port> support.
The last format is used by kernel and other drivers.
Change-Id: I6528970d3af4f6a8bf7b27a0f7a763b5957fdf2b
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4631
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This pseudo target allows attaching to any access point on the DAP at the
MEM-AP level and read and write addresses on the connected bus. For
example, one can create a mem_ap target on the APB-AP and read and write
registers of debug components directly. This allows many diagnostic
and other features be programmed entirely using TCL, without necessity
of adding drivers to OpenOCD.
Change-Id: I53229ffd68fb0f96fb68be15b0f3a76cc8843c8e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4002
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Leonard Crestez <cdleonard@gmail.com>
The argument passed to global config command "gdb_port" is usually,
but not always, a TCP port number. In case of multiple targets, this
numeric value is used as the first port of a set of consecutive TCP
ports assigned one per target.
If the argument is not a numeric value (e.g. "pipe", "disabled", ...)
then incrementing it for the next target has no sense.
Add the option "-gdb-port number" to the commands "target create" and
"$target_name configure" to override, for the specific target, the
general global configuration.
This permits to use a per target "-gdb-port disabled", when no gdb
port is required for that specific target.
It also makes possible to choose a custom TCP port number for each
target, overriding the usual sequence of consecutive port numbers.
Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4530
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The AP number value is restricted in 8 bits unsigned by ADI-v5
specification. Nevertheless, an "invalid" value is used by
target cortex-m to force an automatic detection of the AP.
Replace magic numbers by using new macros for AP max number and
for the value of AP invalid.
Check the value passed through -ap-num flag during configuration.
Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4668
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Read-modify-write setting of FMR register requires an USB turnaround.
Setting FMR before each page write is not necessary and decreases the
write speed.
Change-Id: I67844c898aaf117f155c762c979840b603c767ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4611
Tested-by: jenkins
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.
To use, add the following lines to ~/.gdbinit.
define hookpost-file
eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end
And please make sure the above values are the same as in
src/rtos/nuttx_header.h
Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The fall-through comment is not taken in consideration by gcc 8.1.1
because it is inside the braces of a C-code block.
Move the comment outside the C block.
Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4614
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
rename shutdown original_shutdown
proc shutdown {} {
puts "This is my implementation of shutdown"
# my own stuff before exit OpenOCD
original_shutdown
}
Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.
Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".
Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.
Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
There is no need to pass through DR-/IR-Pause after a scan if we want to
go to DR-/IR-Update. We just have to skip the first step of the path to
the end state because we already did that step when shifting the last
bit.
v2:
- Fix comments as remarked in review of v1
Change-Id: I3c10f02794b2233f63d2150934e2768430873caa
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/4245
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If a NULL pointer is passed, don't attempt to increment it. This avoids
passing the now not-NULL pointer on and eventually segfaulting. Also
remove some unnecessary temporary variables.
Change-Id: I268e225121aa283d59179bfae407ebf6959d3a4e
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit 5087a955 added custom signal handlers for the openocd
server process.
Before this commit, when openocd is run as a background process
having the same controlling terminal as gdb, Control-C would be
handled by gdb to stop target execution and return to the gdb prompt.
However, after commit 5087a955, the SIGINT caused by pressing
Control-C also terminates openocd, effectively crashing the
debugging session. The only way to avoid this is run openocd in
a different controling terminal or to detach openocd from its
controlling terminal,
thus losing all job control for the openocd process.
This patch improves the server's handling of POSIX signals:
1) Keyboard generated signals (INT and QUIT) are ignored
when server process has is no controlling terminal.
2) SIGHUP and SIGPIPE are handled to ensure that .quit functions
for each interface are called if user's logs out of X
session or there is a network failure.
SIG_INT & SIG_QUIT still stop openocd
when it is running in the foreground.
Change-Id: I03ad645e62408fdaf4edc49a3550b89b287eda10
Signed-off-by: Brent Roman <genosensor@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There was already a github fork that had this fixed, but as we try
to use the latest, non-modified version of all software we use,
I would like to have this fix in the next releases of OpenOCD so
that if people uses $packagemanager, they will not have issues flashing
the last part of the flash of sam4sa16c chips.
Additionally, I've added some more logging related to the flash
bank that was used, and the chip ID that was detected.
Change-Id: I7ea5970105906e4560b727e46222ae9a91e41559
Signed-off-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4599
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
No need to wait until after connecting, might help diagnose part information by
printing earlier.
Change-Id: I51eb0d584be306baa811fbeb1ad6a604773e602c
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3404
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the right word in flash protect command status messages based on
whether the target bank defines num_prot_blocks. Minor message style
tidy-up.
Change-Id: I5f40fb5627422536ce737f242fbf80feafe7a1fc
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4573
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
AICE2 doesn't support scan for the maximum clock frequency of
JTAG chain. It will cause USB command timeout.
Change-Id: I41d1e3be387b6ed5a4dd0be663385a5f053fbcf9
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4292
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Corrects names of SAMD11D14AM and SAMD11D14ASS per datasheet.
Change-Id: I8beb15d5376966a4f8d7de76bfb2cbda2db440dc
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Reviewed-on: http://openocd.zylin.com/4597
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
psoc5lp_erase_check() was not properly adapted to the new
armv7m_blank_check_memory() in the hot fix 53376dbbed
This change fixes handling of num_sectors in dependecy of ecc_enabled.
Also add comments how ecc_enabled influences num_sectors.
Add pointer to default_flash_free_driver_priv() to all psoc5lp flash
drivers to keep valgrind happy.
Change-Id: Ie1806538becd364fe0efb7a414f0fe6a84b2055b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4569
Tested-by: jenkins
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
In a multi-target environment we are supposed to have a single
gdb server for each target (or for each group of targets within
a SMP node).
By default, the gdb attached to a server sends its command to
the target (or to the SMP node targets) linked to that server.
This is working fine for the normal gdb commands, but it is
broken for the native OpenOCD commands executed through gdb
"monitor" command. In the latter case, gdb "monitor" commands
will be executed on the current target of OpenOCD configuration
script (that is either the last target created or the target
specified in a "targets" command).
Fixed in gdb_new_connection() by replacing the current target
in the connection's copy of command context.
Change-Id: If7c8f2dce4a3138f0907d3000dd0b15e670cfa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4586
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
When GDB quits (e.g. with "quit" command) we first execute
gdb_detach() to reply "OK" then, at GDB disconnect (either TCP
or pipe connection type), we execute gdb_connection_closed().
In case GDB is killed or it crashes, OpenOCD only executes the
latter when detects the disconnection.
Both gdb_detach() and gdb_connection_closed() trigger the event
TARGET_EVENT_GDB_DETACH thus getting it triggered twice on clean
GDB quit.
Do not trigger the event TARGET_EVENT_GDB_DETACH in gdb_detach()
and let only gdb_connection_closed() to handle it.
Change-Id: Iacf035c855b8b3e2239c1c0e259c279688b418ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4585
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The name of the bit according to the reference manual is inconsistency
error, not increment error.
Change-Id: Ie3b73c0312db586e35519e03fd1a5cb225673d97
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On a specific early-return path, an allocated working area was not
freed. Free it.
Change-Id: I7c8fe51ff475f191624086996be1c77251780b77
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash operation errors that occur during algorithm programming are
reported via the algorithm return value. However, Flash operation
errors that occur during non-algorithm work (erasing, programming
without a work area, programming the last non-multiple-of-32-bytes on
an H7, etc.) generally end with a call to stm32x_wait_status_busy,
which reads the status register and clears the error flags but fails
to actually report that something went wrong should an error flag
(other than WRPERR) be set. Return an error status from
stm32x_wait_status_busy in those cases. Correct a log message
accordingly.
Change-Id: I09369ea5f924fe58833aec1f45e52320ab4aaf43
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4519
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The proc cmsis_dap_swd_switch_seq() is part of the SWD API for
this interface driver. It is valid only when the interface is
used in SWD mode.
In this proc there is the need to call, in sequence, first
cmsis_dap_cmd_DAP_Disconnect() then cmsis_dap_cmd_DAP_Connect().
The latter call requires the connection mode as parameter, that
inside cmsis_dap_swd_switch_seq() can only be CONNECT_SWD.
The current implementation is not correct and in some cases can
pass mode CONNECT_JTAG. Moreover, JTAG is optional in CMSIS-DAP
and passing mode CONNECT_JTAG triggers an error with SWD-only
interfaces.
Use mode CONNECT_SWD in SWD specific cmsis_dap_swd_switch_seq().
Change-Id: Ib455bf5b69cb2a2d146a6c8875387b00c27a5690
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4571
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
The erase check routine checked sectors only if is_erased != 1
Check sector unconditionally.
While on it fix clang static analyzer warnings.
Change-Id: I9988615fd8530c55a9b0c54b1900f89b550345e9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4401
Tested-by: jenkins
Cached flash erase state in sectors[].is_erased is not reliable as running
target can change the flash.
Autoerase was issued before flash write on condition is_erased != 1
Remove autoerase completely as it is a quite non-standard feature.
Change-Id: I19bef459e6afdc4c5fcaa2ccd194cf05be8a42b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4400
Tested-by: jenkins
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Erasing is not supported by the hardware, it can be written directly.
Tested on CY8CKIT-059, except modifying-write.
Change-Id: I6e920ed930dcd5c7f0b10c5b1b4791a828d9080a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3434
Tested-by: jenkins
Change #3432 was merged into git master without adapting it
to #4297 "prepare infrastructure for multi-block blank check".
This is a fast fix of PSoC5LP specific blank check.
Not tested on real PSoC5LP device.
Change-Id: I7dc13ee7bd1f07b2bfe5a93a5030c0c482d30f00
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4557
Tested-by: jenkins
libusb-1.0.22 has deprecated the libusb_set_debug function. This
function was present in the XDS110 driver as an artifact left over
from early debugging. It isn't required because logging is disabled
by default. Removing it to simplify the code and no longer need to
have libusb version specific #if's in the code.
Change-Id: I9c3f16c039da3f3fad9c4a1169978b0d85a1b45c
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4553
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Always probe for ECC mode and display ECC sectors if disabled.
Non-ECC write is implemented as zeroing the ECC/config bytes.
Erasing ECC sectors is ignored, erase-checking takes them into account.
Tested with CY8CKIT-059 (CY8C5888), except ECC mode.
Change-Id: If63b9ffca7ad8de038be3c086c49712b629ec554
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3432
Tested-by: jenkins
Added cc3220sf flash driver to support the TI CC3220SF
microcontrollers. Implemented flash driver to support the
internal flash of the CC3220SF. The implementation does not
support the serial flash of the CC32xx family that requires
connection over UART, and not via JTAG/SWD debug. Added config
files for both CC32xx devices (no flash) and CC3220SF (with
flash).
Updated to implement comments from code review.
Additional updates to handle remaining comments from review.
Additional updates per review.
Added code to only request aligned writes and full 32-bit
words down to flash helper algorithm. Updated for recent
changes in OpenOCD flash code.
Removed cc32xx.cfg file made obsolete by this patch.
Change-Id: I58fc1478d07238d39c7ef02339f1097a91668c47
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4319
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch fixes a bug where target fails to resume after completing GDB FileIO.
We need to update target last run control information to decide resumption. This
was not being done for vcont packets.
Change-Id: I44bea31720f8b877dba97d77a202303d546ea5bd
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4539
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When destroying the target, if the semihosting
pointer is set, free it.
Change-Id: I07d34918bb3fddab1eee11219dd66f4842708ec1
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4552
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
flash_bank structure of 'virtual' flash driver is a full copy of
the master flash_bank structure including bank->sectors and
bank->prot_blocks pointers. These pointers point to memory
locations allocated by the master driver and thus master driver
is responsible for deallocating them.
Do not free bank->sectors and bank->prot_blocks of 'virtual'
driver since they were already released by master flash driver.
Change-Id: I01f373d4adb3fc79e2724964926b9276442c5c52
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4504
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The test is overly complicated and unreadable.
Simplify it while keeping the exact same behaviour.
Change-Id: I6b22291ca454e1eddeeab4024d3983dc4c603d3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4512
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The name of the command is already printed before the string
in ->usage, thus it appears twice.
E.g.
> help examine
stm32f4x.cpu arp_examine arp_examine ['allow-defer']
used internally for reset processing
stm32f4x.cpu examine_deferred examine_deferred
used internally for reset processing
stm32f4x.cpu was_examined was_examined
used internally for reset processing
Remove the command name from the string in ->usage.
Change-Id: If3b1368ffff8a94eb629ae3679e2e5f2f11ae92e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4536
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In 2016, ARM released the second edition of the semihosting specs
("Semihosting for AArch32 and AArch64"), adding support for 64-bits.
To ease the reuse of the semihosting logic for other platforms
(like RISC-V), the semihosting code was isolated from the ARM
target and updated to the latest specs.
The new code is already in use since January (in GNU MCU Eclipse
OpenOCD) and no problems were reported, neither for ARM nor for
RISC-V targets, after more than 7K downloads.
The 2 new files were formatted with uncrustify.
Change-Id: Ie84dbd86a547323bb8a5d24eab68fc7dad013d96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4518
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Recent Linux maps GPIOs from 1023 downwards so do not limit the number
to 1000.
This should fix#183.
Change-Id: I6d4f493b670be9ed9b82759f0fb686a9faddbbf5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4502
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.
Updated to add better support for swd switch. Removed issues found with
clang static analysis.
Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).
Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
gcc (GCC) 8.1.0 generates new warnings and thus fails the build.
The ARM disassembler warnings actually exposed a bug in SMALW, SMULW and
SMUL instructions decoding.
Reported by Eimers on IRC.
Change-Id: I200c70f75a9e07a1f13a592addc1c5fb37714440
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4526
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Neither the initial loop to clear dirty registers (which visits all
registers starting at R2 and counting upwards) nor the final explicit
flushes ensure a write-back in arm_dpm_write_dirty_registers.
This change makes sure that both our scratch registers (i.e. R0 and
R1) are written back to the target.
Change-Id: If65be4f371cd40af9a0cfa97f3730b070b92e981
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-on: http://openocd.zylin.com/4506
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Mostly trivial fixes spotted by spell checker
One fix s/are/is/
No changes in the content of the document
Change-Id: Ic2d8696860c540e901e8c5190f8f1e7dce80545f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fixed style issue.
Removed #define with list of strings, and just put the
strings in the array initialization directly.
Removed empty space at the start of line.
Change-Id: I76580be203d7d69b8c5b5440f820156543e0d5cc
Signed-off-by: Faisal Shah <faisal.shah@gmail.com>
Reviewed-on: http://openocd.zylin.com/4488
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash loaders refactored to the new style - use generated .inc
instead of hexadecimal machine code in the flash driver source.
Change-Id: If65a2099589e210f9450819b467d67819fd841fc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4439
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The "Blue Pill" is a popular development board with an STM32F103C8
micro controller. According to sources, it has a 128kB Flash on board
even though the option bytes only report 64kB. This patch therefore also
modifies target/stm32f1x.cfg to take an optional FLASH_SIZE variable into
account which the board file sets to 0x20000.
Change-Id: I8a78ccd2b5faf637c539ee3cf8136789ee15c95d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4495
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add configuration for the Renesas R-Car R8A7790 H2 target.
This is an SoC with four Cortex A15 and four Cortex A7
ARMv7a cores, only the four A15 cores are supported.
Change-Id: I6099b257cc0f04e6858ed5f5f8c8d8ad82ef7650
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4490
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Minor fix, no code change, just align it to the block it belongs to.
Change-Id: I4c3b0d0bd00a55d5109d3723e5c4bfb2fc72e366
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4492
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Vybrid VF6xx SoCs contain an additional Cortex-M4
core connected to AP number 3 of the main DAP.
Change-Id: I59c020fdfc53e909b1f0dac1a8627a62cdaa74f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3640
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Cortex-M target used 'auto_bp_type' mode. The requested type
of breakpoint was ignored and hard (FPB) breakpoints were set in
'code memory area' 0x00000000-0x1fffffff, soft breakpoints were set above
0x20000000.
The code memory area of Cortex-M does not mean the memory is flash and
vice versa. External flash (parallel or QSPI) is usually mapped above
code memory area. Cortex-M7 ITCM RAM is mapped at 0. Kinetis
has a RAM block under 0x20000000 boundary.
Remove 'auto_bp_type' mode, set breakpoints to requested type.
Change 'cortex_m maskisr auto' handling to use a hard temporary
breakpoint everywhere: it can also workaround not working soft breakpoints
on Cortex-M7 with ICache enabled.
Change-Id: I7a9f9464c5e10bfd7f17cba1037ed07a064fa2e8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4429
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
includes target configuration for i.MX8M SoC family,
board file needs to set up CHIPNAME and CHIPCORES
to match the actual hardware configuration
Change-Id: Ieb6d89cab2477a58f85d0ef9cd242710950191c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4434
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
configuration also contains a reset-init procedure that disables the
watchdog and initilizes the boards DDR memory so that you can upload
baremetal (e.g. boot loader) code into DDR and start it from there.
Change-Id: I4d2311b3708a5fcb5174a3447f34ae3904de7243
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Microchip (former Atmel) SAM drivers allocate a struct per chip.
at91sam3, at91sam34:
Deallocate all chip structs from the list at once, on the first bank
deallocation.
at91samd and at91sam4l drivers do not handle more than one bank.
Convert them to simple driver_priv allocation and use
default_flash_free_driver_priv().
Change-Id: I49d7200f38a4568c7e12f306c27d1b1b72646736
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4416
Tested-by: jenkins
Most of flash drivers have to ensure proper flash write block alignment
and padding. As there was no support for it in the flash infrastructure,
each driver does it its own way. Sometimes this part of code is not properly
tested and contains bugs.
flash_write(_unlock) joins all image sections targeted to one flash bank
using padded areas as a glue. This solves alignment problems on section
boundaries but imposes other problems.
Introduce new flash bank parameters write_start_alignment,
write_end_alignment and minimal_write_gap.
New flash drivers can just properly set these values instead of handling
alignment by its own.
Adapt infrastructure (namely flash_write_unlock(), handle_flash_fill_command()
and handle_flash_write_bank_command()) to prepare write data padded
to an alignment required by the flash bank.
Rework flash_write_unlock() to discontinue write block when the gap
between sections is bigger than minimum specified in minimal_write_gap.
minimal_write_gap is set to one sector by default.
Change-Id: I4368dd402dfaf51c193bcbf1332cffff092b239b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4399
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Add configuration for the Renesas R-Car R8A7791 M2W target.
This is an SoC with two Cortex A15 ARMv7a cores, both cores
are supported.
This patch is based on initial submission by Adam Bass and
improvements by Niklas Söderlund.
Change-Id: I297da62b9ce71ad222a401d98e6bcb8502427673
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Adam Bass <adam.bass@renesas.com>
Cc: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-on: http://openocd.zylin.com/4485
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This also fixes the transport_is_hla FIXME.
Change-Id: I33960f373f11e3e203f9aed9c6d02bf7ca48ac97
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4473
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use sector sizes instead of bank size.
Detect a gap between sectors and emit xml blocks accordingly.
Detect sector overflow over the bank size.
Change-Id: If0e0e44b0c3b93067b4d717c9c7b07c08582e57b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4436
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Structures rtos_standard_Cortex_M4F_stacking and
rtos_standard_Cortex_M4F_FPU_stacking in rtos_standard_stackings.c
where using rtos_standard_Cortex_M3_stack_align for the stack-align
function. This function calls rtos_Cortex_M_stack_align with
XPSR_OFFSET = 0x3c. This offset is correct for cortex-M3 but not for
cortex-M4F and cortex-M4F with fpu. This patch adds stack_align
functions for M4F an M4F_FPU
Change-Id: If6a90b1898fccbb85619a10f3aef5277dd88ce47
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Reviewed-on: http://openocd.zylin.com/4037
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
On SMP targets, the "target smp" command creates a list of targets
that belong to the SMP cluster. Free this list when a target gets
destroyed on shutdown. For simplicity, the complete list is free'd as
soon as the first target of the SMP cluster is destroyed instead of
individually removing targets from the list.
Change-Id: Ie217ae1efb2e819c288ff3b1155aeaf0a19b06be
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
With this option enabled (it's disabled by default) errors accessing
registers are returned to gdb. Otherwise they are ignored and success is
reported to gdb. (This is the current behavior.)
We want this for RISC-V, but there's still some cleanup that needs to be
done before that can be upstreamed.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7e56109ea52d18b780c14a07fb35f9e6e8979da4
Reviewed-on: http://openocd.zylin.com/4452
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add option "nvmuserrow" to "at91samd" for changing and reading the register at 0x804000 which represents various fuses.
Change-Id: I6382cc4ac15e6b9681e2f30b0ae60397a6289c3b
Signed-off-by: Stefan Arnold <sarnold@sh-sw.de>
Reviewed-on: http://openocd.zylin.com/4260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HWID originally added in commit 7829f31a6d
was accidentally omited during refactoring in commit
52885d2b53
While on it move old ingeneering sample of 51822 to block of 51822 rev 1
Change-Id: Ie9f15563792a27a72e71df6edbcc6b04490370ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4437
Tested-by: jenkins
KitProg firmware does not send a zero length packet at the end of the bulk-in
transmission of a length divisible by a bulk packet size. This is inconsistent
with the USB specification and results in jtag_libusb_bulk_read()
waits forever when a transmission of specific size is received.
Limit bulk read size to expected number of bytes for problematic tranfer sizes.
Use 1 second timeout as the last resort.
Change-Id: Ice80306424afd76e9fbc6851911ffd5109c84501
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4426
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Avoid ever overflowing the DWT_COMPARATOR array by allocating space for
16 comparators (the field is masked by 0xf).
On a stm32f767zi chip (on a nucleo-767zi board) I've been seeing crashes
with address sanitizer enabled due to its (apparent) 10 present
comparators. This appears to be due to
https://sourceforge.net/p/openocd/tickets/178/.
In non-address sanitizer builds, this would likely cause some random
memory to be written to in some cases. (see above bug for observations).
Change-Id: I2b7d599eb326236dbc93f74b350c442c9a502c4b
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4458
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All drivers which simply allocate one driver_priv memory block
per each bank now use default_flash_free_driver_priv()
Change-Id: I425bf4213c3632f02dbe11ab819c31eda9b2db62
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4417
Tested-by: jenkins
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Most Xilinx FPGA devices contain an embedded, unique device identifier.
The identifier is nonvolatile, permanently programmed into the FPGA, and is
unchangeable providing a great serial / tracking number.
This commit adds generic support for reading the Xilinx Spartan 6 and 7
Series (Kintex, Artix, Ultrascale) Device DNA. The code is similar to
the function in fpga/xilinx-xc6s.cfg for Spartan 6 but the register
addresses are different and the logic has been simplified.
The code was not placed in xilinx-xc7.cfg. The approach of defining taps
in the same file as library code to use them is fundamentally broken on
boards that have more than one FPGA or other chips. This commit (like
the addition of support for Xilinx XADC) starts to remedy that by
splitting library code from board-specific fixed definitions.
The support code is sourced in the Kasli and KC705 board support files
as it was tested on these boards.
Change-Id: Iba559c7c1b7e93e1270535fd9e6650007f3794da
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4396
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Also call adapter_exit() before command_exit() as the latter releases
Jim interpreter so JTAG events should be released before.
Fixes memory leak reported by valgrind
Change-Id: I493f3fcba34ea2b4234148e79a4e329c866e0f05
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4474
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If a target is run from gdb and then stopped from OpenOCD telnet interface,
halt does not show message with status and PC registers.
While on it rename 'display' to 'verbose_halt_msg' and use bool type
instead of int.
Change-Id: Ibe6589015b302e0be97258b06938c297745436a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4475
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Kasli is an open hardware FPGA board. It is part of the Sinara family of
devices designed to control quantum physics experiments (see Sayma_AMC
for other boards already suppported by openocd).
Kasli was developed as part of the opticlock project. It features a
Xilinx Artix 7 100T FPGA, DDR3 RAM, a clock reconstruction and
distribution network, four 6 Gb/s transceiver links (three SFP and
one SATA) as well as interfaces to up to 12 Eurocard Extension Modules
(EEMs).
https://github.com/m-labs/sinara/wiki/Kaslihttp://www.opticlock.de/en/
Change-Id: I88b5e9f16b79e1e731056c45da6b5e1448d2c0e7
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4341
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Ultrascale series is a bit more complicated to handle since with the
stacked and interconnected dies the IR gets longer. This adds support
for all currently known chips from the Ultrascale family.
Change-Id: Ibac325dd6fadc76f73cc682b1c62c1a5f39f0786
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4188
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
provide meta information for the cpsr so gdb can display the status
flags and not only a hexadecimal number
Change-Id: I9d3fb29153780adbea389d7e4175d5e19bddc256
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4460
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
and move declaration of all transport_is_xxx() functions to transport.h
Change-Id: Ib229115b5017507b49655bc43b517ab6fb32f7a6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4469
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.
If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.
Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If we enter debug state from EL0, some registers are not accessible.
Temporarily move to EL1H and back to gain access. Also, fix
armv8_dpm_modeswitch() to not immediately restore the previous state
on elevating the privilege level.
Change-Id: Ic2a92109230ff4eb6834c00ef544397a5b7ad56a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4461
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
gdb assumes that a rtos can make any thread active at will in response
to a 'Hg' packet. It further assumes that it needs to step-over after
setting a breakpoint on frame #0 of any non-current thread. Both
assumptions are not valid for an actual rtos. We fake the step-over to
not trigger an internal error in gdb. See
https://sourceware.org/bugzilla/show_bug.cgi?id=22925 for details.
Change-Id: Ida60cd134033c1d58ada77b87fe664a58f61e2c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4448
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Normally, when a ctrl-c is received from gdb, a SIGINT is reported back
unconditionally to tell gdb that the target has stopped in response.
However when a rtos support was configured, the rtos awareness overwrote
the signal with an actual thread state, which gdb then ignored and got
stuck without the user able to interrupt.
Change-Id: I40fd62333e020a8c4d9df0079270e84df9c77f88
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4445
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Also uses calloc() for mpsse_ctx->write_buffer to prevent a false
positive valgrind report
"Syscall param ioctl(USBDEVFS_SUBMITURB).buffer points to uninitialised bytes(s)"
Change-Id: I91963371d15c21ea0fee4c40c1da86174db44520
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4418
Tested-by: jenkins
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.
Change-Id: I3a7a9c8e8dc7557aa51d0b9caa244537e5e7007d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4410
Tested-by: jenkins
If OpenOCD command line contains -c shutdown, server_quit() is not called.
Though if -c init is also on command line, gdb_server is already initialized.
Call server_quit() on both successful and failure exit from command line.
Change-Id: I6df41c5df045b61d84a5515d1abaa5dc96bc30ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4409
Tested-by: jenkins
Make sure the user is aware he can lock the device though unlock is not
possible without access to MDM-AP.
Change-Id: I92676530e95d19489c6739748a99c2895849f90f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4403
Tested-by: jenkins
When a user asks for blaster I, he or she should either get it, or get
an error, not blaster II driver.
Change-Id: Ibc7683676ce42773e2b14ea5ccb3d119d1e6acea
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4381
Tested-by: jenkins
Change occurrences of char to uint8_t where appropriate as a binary
protocol is used to talk to this adapter.
This fixes a build issue with modern clang.
Change-Id: I21cc82c8cad148bd0977533c12c74a9d6ba2faff
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4462
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is a second try for this patch. I removed the queues from the
previous version. I made it compatible with SRST reset and added
support for those features that could be supported in raw binary
mode.
Change-Id: I96fc06abbea9873e98b414f34afd9043fd9c2a41
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/3960
Tested-by: jenkins
Reviewed-by: Eric Work <work.eric@gmail.com>
Reviewed-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jacob Alexander <haata@kiibohd.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While on it
- change some occurrences of gdb to GDB if it refers GDB software
(as oposed to a gdb command)
- add some xrefs
- give more meaningful example of target event definition
- remove obsoleted example of GDB hook-step
Change-Id: Ia2e26021d57f675acfa1de704f6c3e81c22bb8bf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4444
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Without this, we have some types promoted to `int` when they need to be
`unsigned int`.
Here's some ubsan output hitting this:
Unfortunately, what happens is that things get promoted to `int`, but
need to be `unsigned int`. Here's the ubsan output:
src/helper/types.h:126:65: runtime error: left shift of 255 by 24 places cannot be represented in type 'int'
#0 0x55978a612060 in le_to_h_u32 src/helper/types.h:126
#1 0x55978a61ff9e in stlink_usb_read_reg src/jtag/drivers/stlink_usb.c:1539
#2 0x55978a8cfd45 in adapter_load_core_reg_u32 src/target/hla_target.c:67
#3 0x55978a9f48e3 in armv7m_read_core_reg src/target/armv7m.c:236
#4 0x55978a8d24fc in adapter_load_context src/target/hla_target.c:372
#5 0x55978a8d261b in adapter_debug_entry src/target/hla_target.c:396
#6 0x55978a8d3123 in adapter_poll src/target/hla_target.c:457
#7 0x55978a528357 in target_poll src/target/target.c:535
#8 0x55978a539fd4 in target_wait_state src/target/target.c:2914
#9 0x55978a556e20 in jim_target_wait_state src/target/target.c:5256
#10 0x55978a5cca62 in command_unknown src/helper/command.c:1030
#11 0x55978aaed894 in JimInvokeCommand /home/cody/d/openocd-code/jimtcl/jim.c:10364
Change-Id: I24f6abfd26b6980100657397d69c84f2b80a005a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4455
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Instead of re-reading ttbcr and ttb0/1 whenever a virt2phys translation
is done, cache the values once when entering debug state. Use the cached
values in armv7a_mmu_translate_va().
Change-Id: I1bc5349ad2f19b2dd75bdd48468a2c1f1e028699
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3112
Tested-by: jenkins
This patch adds support in openOCD to read/write Arm vector/floating
point registers. This is compatible with Arm vfp v3 target xml in GDB.
Please refer to binutils-gdb/gdb/features/arm/arm-vfpv3.xml
Change-Id: Id4dd1bddef51c558f1a86300c1a876d159463f18
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4421
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
This patch adds support for read/write of SIMD and floating-point register in AArch32 mode.
This patch is tested using Raspberry Pi3 halted in AArch32 mode with FP/SIMD enabled.
Software need to make sure floating-point and SIMD unit is enabled.
Change-Id: I2b3b8af02257c6420e5a70c6f4c91f839c1f5ee5
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4446
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds support in openOCD to read/write AArch64 SIMD/FP registers.
This patch depends on a previous patch which adds support to generation
of target xml by openOCD with nested architecture defined types. AArch64
SIMD/FP registers assumes various types and to support all types we
implement them as architecture defined type aarch64v which in turn
consists of various architecture defined types. This is compatible with
AArch64-FPU target xml in GDB. Please refer to
binutils-gdb/gdb/features/aarch64-fpu.xml
Change-Id: I7ffb0c21b3c2e08f13720b765408b30aab2a9808
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4373
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds support to generate multiple nested architecture defined
data types in gdb target xml generated by openOCD. Architecture defined
structs, unions, vectors nested in one or more architecture defined
types can be generated now.
Example:
<vector id="v2d" type="ieee_double" count="2"/>
<vector id="v2u" type="uint64" count="2"/>
<vector id="v2i" type="int64" count="2"/>
<union id="vnd">
<field name="f" type="v2d"/>
<field name="u" type="v2u"/>
<field name="s" type="v2i"/>
</union>
Change-Id: I0f3c5c6daf3d22cde7e4b7b4165d2e97e25872f7
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4372
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.
Change-Id: If43f02fe594c30ceb1bea3259ea3e098d4b2d239
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4408
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
This patch fixes a memory leak in the internal server. Steps for
reproduction:
* valgrind --leak-check=full --show-reachable=yes ./build/src/openocd
* Establish more than one connection to OpenOCD (e.g. telnet)
* Shutdown OpenOCD
* Check for memory leaks in add_connection()
Change-Id: I0ae6fcf2918fd9bdec350446d3e26742d08ff698
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4053
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
30 MHz is not working reliably here
Change-Id: I38f5f8c7153fc64e313ee911b1629fb5f1114c39
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4242
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is needed for Cortex-M7 devices, which have newer FPU.
This issue caused the registry integrity check to fail if FPU was enabled.
Currently the code must use FPUv4_SP anyway, since other configurations are not
supported by ChibiOS.
Change-Id: Ie8a2cb8282ccff6c2a3eb0ffeaddaf149d55d685
Signed-off-by: Luca Dariz <luca.dariz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4398
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Protection read and setting of the second flash macro did not work.
Tested on CY8CKIT-046
Change-Id: I67789399ad1e89bbfc23a95547ecca7753130701
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4425
Tested-by: jenkins
This change contains an alternative to Matthias Welwarsky's #4130
(target-prefixed commands) and to #4293 (event handlers).
get_current_target() must retrieve the target associated to the current
command. If no target associated, the current target of the command
context is used as a fallback.
Many Tcl event handlers work with the current target as if it were
the target issuing the event.
current_target in command_context is a number and has to be converted
to a pointer in every get_current_target() call.
The solution:
- Replace current_target in command_context by a target pointer
- Add another target pointer current_target_override
- get_current_target() returns current_target_override if set, otherwise
current_target
- Save, set and restore current_target_override to the current prefix
in run_command()
- Save, set and restore current_target_override to the event invoking
target in target_handle_event()
While on it use calloc when allocating a new command_context.
Change-Id: I9a82102e94dcac063743834a1d28da861b2e74ea
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4295
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
A previous fix avoiding multiple calls to the
rtos_create function had a side effect if rtos
support was configured explicitly. It affected
all rtos' that rely on symbol resolution from
gdb.
Change-Id: Id7f17c6ec5ce2450322d2748a4b2369aaa524a7b
Fixes: 3aa8bd2d17
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4438
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
this patch contains several changes to run control and state
handling together with gdb:
- graceful handling of target/gdb desync on resume, step and halt
- a default gdb-attach event executing the "halt" command, to meet gdb
expectation of target state when it attaches
- call target_poll() after Ctrl-C command from gdb
- call target_poll() after resume and step through a vCont packet
- fix log message forwarding on vCont stepping, also move an aarch64
log message from INFO to DEBUG level to prevent messing up the gdb
console during source-line stepping
- fix oversight in vCont support that messes up breakpoint handling
during stepping
Change-Id: Ic79db7c2b798a35283ff752e9b12475486a1f31a
Fixes: d301d8b42f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4432
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
target_start_algorithm does not download the algorithm. It only starts
it. It expects someone else to have already written the algorithm code
into the proper location before calling it.
Change-Id: I5e04406eed0ebb1c23e550dbf8d9f1204c432603
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4435
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
flash_write_unlock() sorts sections by base address but does not check
if they overlap. In case of overlapped sections an item of padding[]
array can get negative and padding loop writes out of allocated buffer.
How to replicate: cat two copies of an ihex file to one file and try
to flash it.
Check for overlapped sections and abort write in such case.
Change-Id: I43eee7dc290a8d18faa59567b2118b88ad4bedca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4397
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
make sure the RTOS thread database is updated early on a new
gdb connection.
Change-Id: I4da9ef30f8634263d697116cefc47976cd1970ad
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4000
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Whenever a "qSymbol" from gdb is received, the rtos "create"
function was called. Make sure this happens only once and only
if rtos autodetection is used.
Change-Id: Ie5f8632cfce2d64a38dbdb63468302c4e8a784f4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3998
Tested-by: jenkins
Reviewed-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The RTOS handlers present OS threads to gdb but the openocd
target layer only knows about CPU cores (hardware threads).
This patch allows closing this gap inside the RTOS handler.
The default implementation just returns the current core, but
a RTOS handler can provide its own function that associates a
an OS thread with a core.
Change-Id: I12cafe50b38a38b28057bc5d3a708aa20bf60515
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3997
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Make gdb use target support for single-stepping if available.
Change-Id: Ie72345a1e749aefba7cd175ccbf5cf51d4f1a632
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3833
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When debugging Thumb-2 code, Gdb will at times send a
breakpoint packet 'Z0,<addr>,3', the number 3 denoting that
the instruction to break on is 32 bits long. Handle this by
replacing it with two consecutive 16bit Thumb BKPTs and make
sure to save and restore the full, original 32bit
instruction.
Note that this fix is only applicable if you debug a bare-metal program
(like the linux kernel) with the 'wrong' gdb, e.g. use an
"arm-linux" gdb instead of an "arm-eabi" gdb. But since most people
may not know about the subtle differences between gdb configurations
regarding thumb2 breakpoints it's still valid.
Change-Id: Ib93025faf35b11f0dba747a8c1fc36fd09a4c0f8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4241
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
The ICEPick-D jtag router has core control registers
that provide the same (or similar) functionality as
the tap control register, for individual cores
accessible through the same tap (e.g. through a DAP).
Core control registers are located at address "0x60 +
core-id" of the ROUTER address space (IR=ROUTER).
It is sometimes helpful or even necessary to modify the
core control register. This patch renames the
"icepick_d_coreid" function to the more appropriate
"icepick_d_core_control" and adds a "value" argument
that allows writing of arbitrary value.
"icepick_d_tapenable" is extended by an optional value
argument so that core control can be written as the tap
is enabled.
Change-Id: I0e7f91b596cb5075364c6c233348508f58e0a901
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
if armv7a_l1_d_cache_clean_inval_all will fail, error value is never
forwarded. So make sure we do it from now.
Change-Id: I02acfaa938ec09f58df77191d13d8f4bb3308720
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4384
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add support for more EFM32/EFR32 Series 1 families. The family IDs
come from the DEVICE_FAMILY list in the EFM32GG11 reference manual,
which is the most up to date source I could find. Register locations
have been checked against SiLab's header files.
No datasheets or headers were available for EFR32MG2, EFR32xG14 and
EFM32TG11B, so they are just assumed to follow the pattern. EFM32GG11B
has the MSC registers on a different address compared to other chips.
This commit attempts not to change current behavior when detecting
chips. One detail that has changed is that PAGE_SIZE is read before
applying the workaround for old Giant and Leopard Gecko revisions, but
this is believed to be OK because the register exists but just has an
invalid value in it.
The manuals disagree on which of 120 and 121 is WG, so this commit
leaves it as is.
Change-Id: Ia152b0b9e323defc5158cb02d9a6b04a27008f2a
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4263
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Images build improperly (by simply concatenating separate images) were accepted,
but anything after the first end-of-file record *silently* ignored. Now emit warning
for intel and motorola images upon non-whitespace after first end-of-file record but
continue reading anyway.
ST ships some images broken that way in their CubeMX packages ...
Change-Id: I0c5d08fa90070fed11fb805c5f0dc39817048176
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash ROM API command PSOC4_CMD_SET_IMO48 is now optional on new devices.
Also code tidy up:
- improved system ROM call error detection
- probe does not require the target to be halted
- default_padded_value and erased_value set to 0
- fixed endianess problem in flash write and protection setting
- removed fancy chip detection table as it would be updated too often
- psoc4 flash_autoerase is now on by default to ease programming
psoc4.cfg distinguishes chip family and uses either proprietary acquire
function of a KitProg adapter or TEST_MODE workaround to "reset halt"
Change-Id: I2c75ec46ed0a95e09274fad70b62d6eed7b9ecdf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3807
Tested-by: jenkins
Reviewed-by: David Girault <david.f.girault@gmail.com>
Microchip SAM R30 consist of a MCU SAM L21 and a radio.
Similarly SAM R21 = SAM D21 + radio. Therefore SAM R devices
was incorporated into SAM D21 and L21 device groups.
Change-Id: I3448d784cae888070b57c2f504583760ddffc97f
Suggested-by: Martin Deicke <martin.deicke@an-solutions.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4282
Tested-by: jenkins
I see no reason for not returning error from target_run_algorithm()
to higher level.
Reported by Clang static analyzer.
Change-Id: Iaaa8b66e487ecae88c0cf4ae2addba63341c032c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4391
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Make all configs specify same JTAG and SWD GPIO numbers.
Change-Id: I65b09c1671c97f253f0aab88e511de7409d91e0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3932
Tested-by: jenkins
Clang static analyzer says that in certain cases "Assigned value is
garbage or undefined" there.
Change-Id: Ib35a4cf7a553ba9461270a0dc4c4b9b205091e73
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4338
Tested-by: jenkins
This fixes parsing of several documentation files which do not have
dot in the filename.
style.txt change fixes doxygen warnings and ensures proper display of
comment begin/end instructions in HTML.
Tested with Doxygen 1.8.13.
Change-Id: I9fd9ac3b51b47076b8fdbd3e93b90c3eba9b9631
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4342
Tested-by: jenkins
scan-build reported a couple of problems with code in aarch64.c,
this patch cleans them up. No functional changes.
Change-Id: Ie210237ddc840a8bbcd535f86a3a5faf473132f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4346
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch should make the code logic more transparent and user
notifications more useful.
It also fixes a warning "array subscript is below array bounds" that
leads to FTBFS on Raspbian GNU/Linux 8 (jessie).
Change-Id: I626b6a5bc013dfee7d36cf196f0abab981d30675
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3931
Tested-by: jenkins
Previously for every bit scanned OpenOCD would write the bit, wait for
that bit to be scanned, and then read the result. This involves at least
2 context switches. Most of the time the next bit scanned does not
depend on the last bit we read, so with a buffer we now write a bunch of
bits to be scanned all at once, and then we wait for them all to be
scanned and have a result.
This reduces the time for one testcase where OpenOCD connects to a
simulator from 12.30s to 5.35s!
Running all our tests went from 13m13s to 3m55s.
Change-Id: Ie9fcea043ac1d7877a521125334ed47d4b3e1615
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4312
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some of these changes actually fix broken comparisons which could
occasionally fail. Others just clean up the code and make it more clear.
Change-Id: I6c398bdc45fa0d2716f48a74822457d1351f81a5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The Flash Configuration Field on Kinetis devices requires protection
because it is located in program flash space (at 0x400) and writing
an improper data to it may permanently lock the device. Even an erased
flash sector containing FCF engages security lock (not permanent one)
on the next reset or power cycle.
'kinetis fcf_source protection' mode was introduced in the change #3562.
Flash driver in this mode sets FCF immediately after sector erase to
prevent unintentional security lock. To do so the driver needs to know
FCF values before flash image data is actually processed. Flash
protection bits are available in bank structure, FOPT can be set by
'kinetis fopt' command and securing device by FSEC is not supported.
Nevertheless an inexperienced user flashed the device using an image
with FCF values different from those set in OpenOCD config and
concluded programming did not work as some verify errors showed.
This change tries to write maximum possible from image data
retaining FCF protection.
Check FCF in programmed data and report if some field differs from
values set by OpenOCD flash block protection and 'kinetis fopt' command.
Warn user about verify errors caused by FCF protection.
On devices with ECC flash (K26, K66 and KV5x) it is impossible to change
already programmed FCF - it would result in an ECC error. As FCF was
written just after erase in 'kinetis fcf_source protection' mode
the warning issued during flash write is the only possible action.
On non-ECC flash devices use cumulative flash programming to
set FCF values requested in programmed image data.
Use FSEC from programmed data only if it does not request a secure
mode. Device can be secured only in 'kinetis fcf_source write' mode.
Use FOPT from programmed data if its value was not configured
in OpenOCD config by 'kinetis fopt' command.
Change-Id: If65fbbd7700069f57e4ae32234dce371bff93674
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4228
Tested-by: jenkins
Reviewed-by: Robert Foss <robert.foss@memcpy.io>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reading options word can fail, so this needs to be handled.
Reported by Clang static analyzer.
Change-Id: I9754cab9c4446fa2b20d4b44b0e20724d1bc1beb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4352
Tested-by: jenkins
Reviewed-by: Tim "mithro" Ansell <mithro@mithis.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Clang static checker emits "Assigned value is garbage or undefined"
warning there as it can't prove that when the socket descriptor is
AF_INET/SOCK_STREAM and getsockname doesn't return an error, sin_port
is guaranteed to be filled in.
Pacify it by obvious means.
Change-Id: I43b5e5ceb41c07d523a81b34a25490c4c5f49a70
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4350
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command
mdw 0 0x40000000
triggers Segmentation fault on an arm.
Size parameter is a nonsence that may happen e.g. if you
mistype mdw instead of mww.
Add checking for calloc() NULL return in mdb/h/w.
Use calloc() instead of malloc() as multiplication
count * sizeof(uint32_t) overflows for size >= 0x40000000.
Change-Id: I968c944d863d1173ef932a7077d526fccb9381ae
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4349
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Don't use atomic dap operations when not necessary. Also remove
loop trying to set core power request, didn't find a platform
where it actually worked and it's slowing examination down.
Change-Id: I44e5c2f289f951b8f4579f08a841172404a52053
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4143
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* Disables the data output pin while SWD is reading, so that a simple FTDI
SWD interface can be made by connecting TCK to SWD_CLK and TDI+TDO directly
to SWDIO. Enabled by setting SWDIO_OE to 0.
Change-Id: I7d3b71cf3f4eea163cb320aff69ed95d219190bd
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Reviewed-on: http://openocd.zylin.com/2274
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Unescaped left brace in string literals is deprecated since perl
v5.21.1.
Not a Perl programmer here so please review!
Change-Id: I724d8fa616d603e032e07afb9b8933e0ec95045b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3801
Tested-by: jenkins
When listening on port 0, the system will assign a random open port. We
use this to run multiple OpenOCD instances against multiple simulators
as part of regression testing. This mechanism means the various test
instances don't have to coordinate to ensure they don't reuse any ports.
The required changes are minimal:
1. Don't increment the port number when it's 0.
2. Print out which port was assigned by the system.
Change-Id: I404c801fc405e9d8eb8420562c02e78d4db6242f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4316
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
added missing instructions from latest available ejtag specification
(MD00047 v6.1 at time of writting) for trace control, fast data channel
and pcsample.
Change-Id: I30293951611265ffc2bd896f9d3ca6b310e5cac6
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3950
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Handle the Ctrl+A and Ctrl+E shortcuts which move the cursor to the
beginning and end of the command line, respectively.
Change-Id: I89fa5fd3c5edeb08a3f9320fda766f72ce9d7f64
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3415
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This duration vs sample count is _significantly_ closer to the truth
than simply declaring the value to be 100Hz.
Change-Id: Ie8d8bdf1959e1aa7cead0631cd2c86afe77d1efc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4221
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Leverages the existing work that added profiling via DWT_PCSR.
hla_target doesn't have direct access to the mem_ap for doing a bulk
repeated read, but simply reading the DWT_PCSR register repeatedly is
still ~2 order of magnitude faster than halt/resume.
Change-Id: Ibe451aa95143694398370fdad6939cfb6191d56f
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4220
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use DWT_PCSR if present (reads nonzero); otherwise do halt-and-sample pc.
Signed-off-by: Simon Schubert <2@0x2c.org>
Change-Id: Id2dc4665e5008cc497a2e6e6493522d038d5af42
Reviewed-on: http://openocd.zylin.com/4211
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
We're using an I/O port reset by default. The only board currently
supported (Galileo) doesn't have SRST routed on the JTAG connector.
When using 'reset halt', we must rely on Reset Break because our
adapters don't have support for PREQ#/PRDY# signals.
Tested with Intel Galileo GEN2.
Change-Id: Ia406e31c156f8001717d5b6a08bd03f71de790d3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When testing with Intel Galileo GEN2 I have noticed a few iterations
where probemode entry took a little longer. At most I had to read
tapstatus twice. This patch uses a loop of up to 100 iterations to
wait for tapstatus to update with PM entry results.
Change-Id: I1c87d7dde715255b3fd2460d299b9493218533fc
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These symbols are only used within this C source file. They don't need
to be exposed to the outside.
Change-Id: Idb04550ecca7f12c3fdc8c6447eeeb871961add3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4012
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Digilent SMT2 NC is nominally the connector-less version of the
SMT2. But neither the SMT2 configuration nor the HS3 configuration work
for on the Xilinx KCU105 board where the SMT2 NC is used.
Change-Id: Ieb27cbc6d8b0f9c64ef778e4e0c839acc85ec0ef
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4187
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When multiple targets are declared, it's not always obvious which
target the connection was made for, this can lead to very confusing
errors.
Reported by zjason on IRC.
Change-Id: I52906320394e89cb6cfe82054a3f94b27c999689
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4135
Tested-by: jenkins
This should allow to process any path names excluding those that have
curly braces.
Change-Id: I87bf9ddede11e2b28d5826878eb1338143f73c03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4083
Tested-by: jenkins
Both MD5 and SHA-1 shouldn't be relied upon since long.
Change-Id: I0dea92fbf0f68b900c0d3a314fb3956d08ba0d48
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3949
Tested-by: jenkins
This doesn't seem to make any sense.
Change-Id: I272de0ea3c0e86cc9a798cbd864050aaa597c3f0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3933
Tested-by: jenkins
Reported by thesourcerer on IRC.
Change-Id: I36d4d95de176a19fdd0bf80d8b419be6ca637e98
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3893
Tested-by: jenkins
When both SRST and TRST asserted, 'u' is sent to remote bitbang.
Fix for correct handling of such a case
Change-Id: I2a93ff71f5bbae658e6c0c3649a9fbcca2c5a14b
Signed-off-by: Aleksey Shargalin <myokaski@gmail.com>
Reviewed-on: http://openocd.zylin.com/4283
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We can now use the generic stlink.cfg which allows for both ST-LINK/V2
and V2-1 debuggers.
Change-Id: I229c6fe5f6a6a4f2d3c787a49939846f102f9e24
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Reviewed-on: http://openocd.zylin.com/4313
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Leaving mode before closing added
Resolved a collision with JTAG API v1 error/status
checking overwriting SWIM status bytes
Change-Id: I35444ec0e6caace3e072c60085059602f4cdf0a4
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/4265
Tested-by: jenkins
Reviewed-by: Philipp Klaus Krause
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fixed a bug in stlink_usb_read_mem/write_mem preventing large data transfers
The SWIM support in stlink_usb was basically non existent so I have
implemented the missing parts. The bCBWCBLength and dCBWDataTransferLength
for STLINK-V1 protocol was not correct so that was fixed. The reason for
adding SWIM support is to add STM8 support for OpenOCD.
I have tested the driver on:
STM8 discovery board with the built-in STLINK-V1
STM8 discovery board with STLINK-V2 dongle
STM32 vldiscovery board with the built-in STLINK-V1
STM32F1xxx processor with STLINK-V2 dongle
Change-Id: I4aa80a92fb0226174356adaf2f8ff949920a621f
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3952
Tested-by: jenkins
Reviewed-by: Philipp Klaus Krause
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions mem_ap_read() and mem_ap_write() incremented address even
if addrinc=false. I overlooked this fact and moved mem_ap_setup_tar()
set wrong addresses in no-incr mode.
Fixed by preventing address increment in no-incr mode.
Change-Id: I512e12a6a64e30cf6bc5bf77e3d57d35cc33e058
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/4326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MEM-AP access through banked data registers MEM_AP_REG_BD0..3
does not increment TAR regardless of the current autoincrement mode.
mem_ap_read_u32() and mem_ap_write_u32() can keep the current
autoincrement mode instead of switching autoincrement off.
Change-Id: Ib7ec688d3e04f1da678363cd2819ce90e8910e58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4163
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The existing code only used Memory Access mode to read memory,
which uses 32 bit operations only.
Rework the code to check the alignment/size of the read/write operation,
and use the Memory Access mode to read aligned 32 bit memory.
When using unaligned access, or 8 or 16 bit reads, use LDR{BHW} and STR{BHW}
instead.
The exception handling is still the same as it was before (meaning it breaks
when things go wrong), but I can now read an 8 bit register correctly.
Change-Id: I739a5ee825c0226ed4a89c32895cc2a047b8dc15
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4301
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit ef02b69b14 included
a call to cmsis_dap_cmd_DAP_Connect() before calling
cmsis_dap_cmd_DAP_SWJ_Sequence(). According to comment
it is necessary for at least Keil ULINK-ME.
Commit 72c3464be4 added
a cmsis_dap_cmd_DAP_Disconnect() before connect call to pair
connection/disconnection. It solves some problems on Atmel EDBG.
Unfortunately calling either of cmsis_dap_cmd_DAP_Connect()
or cmsis_dap_cmd_DAP_Disconnect() deasserts reset signal.
So these workarounds break ability to connect under reset.
Use cmsis_dap_cmd_DAP_Disconnect() and cmsis_dap_cmd_DAP_Connect()
pair only if both SRST and TRST are deasserted.
Change-Id: I0914dae0a1360b8c7fe48231ff3867caedfb2dbe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Leonardo Sabino dos Santos <leonardo.sabino@gmail.com>
Reviewed-on: http://openocd.zylin.com/4100
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Theese devices do not have a gap in sector numbering.
The driver translates sectors numbers 12 13... to 16 17... as used on dual
bank flash devices. Therefore erase of sector 12 and above fails with error
'stm32x device protected'
on F413/423.
Drop sector number translation for devices without has_large_mem flag.
Change-Id: I65531c0dfe02e2fd0f3d68f0615e0926e9901391
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4299
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A protection block comprises two adjacent sectors in dual bank mode.
As there are 64 and 128kB sectors joined in blocks 2 and 8, block size
should be computed as a sum of sector sizes.
Change-Id: Ie915df8cf7ca232c4565d7e0c514c8933e71fdfe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4271
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The CMSIS-DAP used by NXP's LS1012ARDB board only supports JTAG,
and not SWD. Calling cmsis_dap_cmd_DAP_SWD_Configure returns with an
error (and doesn't actually do anything in the debugger).
Wrap the call to cmsis_dap_cmd_DAP_SWD_Configure in a check for
swd_mode, to make sure initialisation doesn't fail needlessly.
Change-Id: Id7e568cb6e36886bd7c5b3699d198a77a51c28c9
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4294
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The SWDIO buffer has to be enabled, by setting SWDIO_OE, for data on
SWDIO to reach the target. Explicitly do this before sending the
switch sequences for JTAG-to-SWD, etc.
This makes the code insensitive to the state of SWDIO_OE specified in
ftdi_layout_init. It used to work only on adapters with a non-inverted
SWDIO_OE inited to 1, or inverted SWDIO_OE inited to 0.
Change-Id: I4b9e520ac1c7ce2a437251a05fc036bc68de718e
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4270
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.
Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.
See also Debian Bug#793214; https://bugs.debian.org/793214
Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The dhcsr_save variable was used to save the value of
cortex_m->dcb_dhcsr so it could be restored later. However, all writes
in between the save and the restore use mem_ap_write_atomic_u32, not
cortex_m_write_debug_halt_mask, which means cortex_m->dcb_dhcsr isn’t
changed anyway. Delete the unnecessary local.
Change-Id: I064a3134e21398e1ecfc9f1fa7efd7b020b52341
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4240
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In cortex_m_assert_reset, in two locations, DHCSR is written directly
using mem_ap_write_u32. This means that the cached version,
target_to_cm(target)->dcb_dhcsr, is not updated when these writes are
performed, so subsequent writes to DHCSR that use
cortex_m_write_debug_halt_mask will change those bits back to their old
values which, unless modified in that particular invocation, come from
the cache. This causes an actual, observable bug on an STM32F7 in which
running “reset run” immediately after “program” can in some cases result
in execution proceeding with C_MASKINTS set (it is cleared on line 1021
but is then set immediately afterward in cortex_m_clear_halt), causing
failure of the application. Replace these mem_ap_write_u32 calls with
cortex_m_write_debug_halt_mask calls to do the same jobs.
Change-Id: Id35ca7f6057c2df2ba9cd67c53a73b50816d0b71
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4239
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
GCC7 with -Wall warns about possible string truncation with
snprint()-type functions with "directive output may be truncated writing
1 byte into a region of size between 0 and 9
[-Werror=format-truncation=]" + "note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 12" (or similar). Fix this by
increasing sizes of buffers.
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Ib848f2a56dd658783534158947ae1be7c0e99d45
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4175
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
GCC7 with -Wextra warns about switch-case blocks which fallthrough with
"this statement may fall through [-Werror=implicit-fallthrough=]". This
can be fixed by adding "special" comments: "/* fallthrough */".
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Iba0be791dbdd86984489b2d9a0592bb59828da1e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4174
Tested-by: jenkins
This config covers the 4x Cortex A53 CPUs. A custom connector
is required from J14 to standard ARM JTAG on v1 boards. However
v2 hardware should have a standard FTSH-105-01-L-DV connector.
Pinmuxing code to enable JTAG pins is included in l-loader-poplar
repository, so board is flashed with open source code, JTAG
is available at very early boot. Alternatively the following
pokes can be issued from U-Boot to enable JTAG (e.g. to debug
hisilicon SDK).
mw 0xf8a210ec 0x130;
mw 0xf8a210f0 0x130;
mw 0xf8a210f4 0x130;
mw 0xf8a210f8 0x130;
mw 0xf8a210fc 0x130;
mw 0xf8a21100 0x130;
Change-Id: I2b83dfcb3dc5461c1620f94dd99aa7b31fdda59b
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-on: http://openocd.zylin.com/4161
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Renaming of all nrf51 NOR flash code to nrf5, as to prepare the
code for being able to flash nrf51 and nrf52 chips.
The nrf51 command is retained for backwards compatability.
"nRF5" is also the name Nordic Semiconductor uses to describe
both the nrf51 and nrf52 chips.
Change-Id: I5f4e3f1ec780184b28ad44f735a746e68908c502
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4209
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Trying to read the L0 idcode at the L1 idcode address 0xE0042000 often
resulted in an uncatched error. Reading at the right L0 address 0x40015800
afterwards results in reading 0. So access to the device is denied..
Change-Id: I6de92cf99a5d5d46c72f9ba055613cbc5753a951
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3883
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
in some cases we need something to test if uart is actually
properly connected.
Change-Id: I5a16b053164b34bb30ae8370753be12887a85c51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Make this error message more useful by providing the port number
that we tried to bind to.
Change-Id: Ieb18adf0725a6ae99c77ebfaadc49d64ed407bbe
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-on: http://openocd.zylin.com/4157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Use unsigned constant for left shift operation in order to avoid the
following error with GCC >= 6.0:
../src/flash/nor/stm32f2x.c: In function ‘stm32x_handle_unlock_command’:
../src/flash/nor/stm32f2x.c:1324:67: error: left shift of negative value [-Werror=shift-negative-value]
stm32x_info->option_bytes.optcr2_pcrop = OPTCR2_PCROP_RDP | (~1 << bank->num_sectors);
Change-Id: I0ac082bd0dbb8dc2f61ffff8fdf486ab7962d2e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4207
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Anton Fosselius <anton.fosselius@gmail.com>
Reviewed-by: Esben Haabendal <esbenhaabendal@gmail.com>
If no serial number is specified, disable TCP/IP device discovery to
ensure that a user does not unintentionally operate on a remote device.
Change-Id: I6a7e913b8b679fae003825468cd86d2014849b29
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4214
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple devices are attached, do not automatically use the first
device found. Otherwise, a user may unintentionally operate on the
wrong device.
Change-Id: I08c4110b82e911e9e3e744d41830ffc6c56c44bf
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4213
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use a human-readable error description rather than just the error name
in log messages.
Change-Id: Iab4ff7a7e4d9993983a07eab9f462820d4ee8190
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4212
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
libusb is now optional for libjaylink because support for TCP/IP
devices is always available.
Change-Id: I03f2566f8e1703276671ac0f353f72394d21f2f0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4204
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Update to latest Git version and bump required libjaylink package
version to 0.2.0.
This version introduces support for devices with TCP/IP interface (e.g.
SEGGER Flasher ARM) and an additional debug level for I/O messages.
Change-Id: I030236aa704a91d1bb1843dd30010865947747e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4202
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A common use case seen in the wild is echoing a string of commands to an
existing openocd instance via netcat. The sequence of ; separated
commands can easily run over the line limit of only 256 chars.
Increasing this dramatically reduces surprises, at the expense of a tiny
amount of extra ram usage.
Change-Id: I2389d99d316a96b5fa03f0894b43c412308e12c4
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4132
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
IDs for STM32F722, F723, F413 and F423 added, handling of PCROP
for F722/723 and additional nWPRT bits for F413/423 implemented.
The additional protection bit positions for F413/423 conflict
with other options bits for the F7xx variants, additionally the
last two sectors share a common bit.
Protection for F413 and F767/777 now use protection blocks
rather sectors for dealing with protections bits.
Checking for halted state in 'lock' and 'unlock' removed: When
PCROP is activated in F723, halted state is not detected properly,
but lock/unlock sequence is required to disable PCROP.
Tested with STM32F723E-Disco, STM32F413ZH-Nucleo.
Change-Id: Ie6ddab47a9ae8461087d369b4f289b7f9d1e031c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4045
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change ftdi SWD driver and CMSIS-DAP to use it instead of LOG_DEBUG().
Change-Id: I17ba3de2086c7159209db61fba3faf067dfc5023
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3805
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If a MCU has FlexNVM partitioned as EEPROM backup only
(no data flash), kinetis_probe_chip() detects zero fcfg2_maxaddr1
and adjusts flash banks count to 1, what is obviously wrong.
The change limits the test to devices without FlexNVM.
Computation of program flash/FlexNVM blocks is now more robust.
Missing case 0x07 is added to switch (fcfg1_depart)
Change-Id: I0bd6030a0fe1ab62aeb0223bbdf2aee1505bf6a0
Reported-by: simon.haines@scalardata.com
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4180
Tested-by: jenkins
Reviewed-by: Simon Haines <simon.haines@scalardata.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch improves the OSRunning check. If the rtos_running check
fails, update_threads will return an error rather than attempt to update
the thread list using bad values.
Change-Id: I8614c325504d3a9ab19aebb6862b1fe445a0c8e7
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4166
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch corrects a number of style infractions in RTOS support for
uC/OS-III. These were missed during initial review last year prior to
the 0.10.0 release.
Change-Id: Ia2139f6ca381d4087fd8ee989f7a03ac474d7440
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4120
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit 47b8cf842 changed the fixed type of the value argument to snprint
but didn't change the format string to match for sizes != 64 bit.
Change-Id: I908b06f49ab69d04224282949190a0de883048e0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/4167
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Philipp Guehring <pg@futureware.at>
Make 'offset' and 'length' parameters optional, if both are omitted
simply read the whole flash bank.
Additionally, check if the 'offset' and 'length' arguments are out of
bounds of the flash bank.
Change-Id: Ib9c1b0538a2c78ebcf702e2da11468dff407f8ff
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3862
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Respect the flash bank boundary and write only to the remaining part of
the bank even if the file content is larger.
Change-Id: I8f4c1b161c103a77bdb30c6bf052293b5ed48c41
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3861
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: I8e9632b539ad9e83211e1ac6a06da4c8109cbc60
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3860
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Respect the flash bank boundary and compare only the remaining content
of the bank even if the file content is larger.
Change-Id: I4d75979c7893fdd4d18372fa6b0321a0486b4fa9
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3859
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for flashing newer members of the NXP Kinetis KW family
Supported devices:
- KW20Z
- KW30Z
- KW40Z
- KW21Z
- KW31Z
- KW41Z
The earlier KW2xD and KW01Z devices are already supported by the code
for the older K-series.
Verified working on the FRDM-KW41Z development board.
Tested flashing both via GDB `load` and directly via OpenOCD flash
write commands.
Change-Id: I73eae477127a8b54a33005b3b526b5439450a808
Signed-off-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-on: http://openocd.zylin.com/4104
Tested-by: jenkins
Reviewed-by: Johann Fischer <johann_fischer@posteo.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This device differs a lot from others in KL series.
Unfortunately the System Integration Module, where device
identification resides, moved to a new address so probe now have
to try both addresses of SIM_SDID.
Introduce a new bank creation option: -sim-base to ensure error free probe.
WDOG32 is slightly different from KE1x and on different address.
System Mode Controler changed layout to word aligned.
Change-Id: I2c9dca0c4ad4228fcc941d6078d15f5e394833ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4059
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver probed and decoded chip repeatedly for each flash
bank. Bank ordering used global bank number so multi-target
configuration was broken.
The change introduces kinetis_probe_chip() which reads SIM SDID
and SIM FCFG registers, decodes Kinetis series and family
and fills struct kinetis_chip. This probe runs once for all banks.
struct kinetis_chip contains pointers to all flash banks embeded
in the MCU. It simplifies iteration over all or specific MCU banks.
kinetis_probe_chip() generates MCU name and some informational messages
are improved.
Change-Id: I990db5c63ba490667eec0e5459086d83936662fb
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3924
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Real time control MCU has a Cortex-M7 and numerous changes in flash layout.
Introduced a new ID of MDM-AP.
While on it a LOG_DEBUG format error fixed.
Change-Id: I1018660ce0c3dd63ac5e2563408fabff3c3daef7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3900
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Secure devices KL81Z7 and KL82Z7 have no SERIESID field in ID register
so they have to be decoded in Kx branch (not KLx).
The flash controller in KL8x and also in K8x devices does not implement
FTFx_CMD_BLOCKSTAT command. Fix kinetis_blank_check() to work properly
using FTFx_CMD_SECTSTAT command only.
Introduce a new flag FS_NO_CMD_BLOCKSTAT to avoid use of FTFx_CMD_BLOCKSTAT
on these devices.
Change-Id: I3ff58718480acd8cce69f618f71667b6b1d9c4f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3898
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Before this change SAMD driver defined "sector" equal to a flash
protection block. Oversize sectors (16kB for the biggest flash size)
made problems for flashing firmware split to two or more parts.
Removed superfluous test of sector protection before erase.
Change-Id: I8e6a6bda6ccd91eda2df67ec48270c69faa1bdd1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3546
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
FWS=6 workaround removed, as this appears to be a copy-paste error
from the SAM3X family. Originally addressed in http://openocd.zylin.com/3837
but not all occurences were removed.
Atmel changed chip naming and removed 91 prefix for atsamg, samd...
Change-Id: Ia2b43da82b2ff9b1c85fdb456a0a198ab095243d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3926
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: http://openocd.zylin.com/3612
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no need to implement scan code in functions
mips_ejtag_get_idcode/impcode(), use mips_ejtag_drscan_32().
Impcode/idcode saved in ejtag.info.
Reorder the code in the callers of this functions.
Change-Id: Ia829c783a0b24c6a65cade736113fa6f67b0a170
Signed-off-by: Salvador Arroyo <salvador@telecable.es>
Reviewed-on: http://openocd.zylin.com/4003
Tested-by: jenkins
Reviewed-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Breakpoint setting based on length (kind) only.
Added 16bit aligned 32bit software breakpoints
support and same filtering before setting
breakpoint.
Set the required isa bit in hardware breakpoints.
Drop the isa bit in software breakpoints.
Change-Id: I7020f27be16015194b76f385d9b8e5af496d0dfc
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Read and save configuration registers, up to 4.
Config3 holds the micromips implementation info.
Added isa implementation info to mips32_common.
Added isa filter to avoid common mistakes, but only
if one isa mode is implemented.
When resuming the isa requested is set if more than
one isa mode is implemented.
Change-Id: I1d6526c5525bffac8d75e031b842b2edc6310e28
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4123
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Needed to run in micromips mode. Seems that if an isa
is supported in debug mode it also supported in kernel
mode. The contrary is not true.
Change-Id: I1feb8e2c376f4db97089f05c20bc0cd177208fb3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4033
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Micromips is 16bit oriented, branch and jumps are
16 bit based. The upper half 16bits of a 32bit instruction
with the major opcode, must go first in the instruction
stream, hence the SWAP16 macro and swap16 array function,
needed if the code is written as 32 bit word in little endian
cores. Endianess info added to ejtag_iinfo. Pointer to
ejtag_info and isa field added to pracc context.
MIPS32 code are renamed to MIPS32_ISA_...
To select the isa, the new code has an additional isa parameter
(1 for micromips, 0 for mips32).
In JR instruction the isa bit must be set to execute
micromips code.
The suffix u is added to the OP codes to avoid signed/unsigned
comparison errors and to make sure the right shift is
performed logically.
The isa in debug mode is updated in the poll function.
Code for miniprograms, in kernel mode, need to be converted.
CFI code only for mips32.
Change-Id: I79a8b637d49b0e2d92b6dd5eb5aa8aa0520bf938
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4032
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Only reencoded MIPS32 instructions. Added some instructions
for crc code. Micromips isa in debug mode is only needed for
pic32mm cores. Pic32mz seems that only works with MIPS32
isa when in debug mode.
Change-Id: I07059e153a7000ea9204f20b6b37edf6a7623455
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4022
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This option is needed, for example, when exiting
debug mode in bmips targets. The last instruction
is a NOP, not a DERET. When working in async mode
this check is not done, mips32_pracc_queue_exec() pass
the parameter to mips32_pracc_exec() and never use it.
Change-Id: I4c7ed4feb1588b62e2645b955b501b6671113b36
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4021
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If max_code is reached realloc memory. If fails to realloc
the error is propagated and every call to pracc_add() returns
immediately. The exec function logs the error.
Change-Id: Idd4ed9d9b8b19b7d6842d0bc5ebb05f943726705
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4020
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
pracc_list points to an array with code in the lower half
and addr in the upper half. Change it to a struct with
an instruction field and an address field.
Requiered to make reallocation easier.
As a side effect the code is less quirky.
Change-Id: Ibf904a33a2f35a7f69284d2a2114f4b4ae79219f
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4019
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Implement it as a function, the code was already in. Added optimize
option.
Change-Id: Ib9ad3f00d6c4f0b91c4e4960a50ec8d102f4e333
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4017
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In most of the cases there is no need to request execution,
the check for a new pracc access already does it.
Requesting execution if not needed makes execution slower and
code larger due the additional checks.
Reduce code in fasdata transfer function.
Call for execution when exiting debug.
Change-Id: I3b45f6d1f62da5fad3e3db84f82a9299b16e1bd9
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4010
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Struct mips32_pracc_context no more in use.
In current code cp0 reg/sel do not requires special handling.
In sync mode ctx.store_count not used, drop check.
In fasdata transfer function use mips32_pracc_read_ctrl_addr()
to reduce code.
Change-Id: Ibd4cfa5a44ebc106ed0db042f4e54a2e0b3d43cb
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4007
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
With this patch OpenOCD shuts down properly when errors occur in the
server instead of just calling exit().
Change-Id: I2ae1a6153dafc88667951cab9152941cb487be85
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3223
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Will be used later, allow queuing all needed scans in a pracc
access. This makes faster execution with ftdi based adapters
working in sync with pracc.
Added now because the overall code is shorter.
Change-Id: Ib32b89307b75785f88870db8d7c9255dc5bbd426
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/4005
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Udev rules for Ambiq Micro ftdi based EVK's.
Two new vid:pid's: 2AEC:6010, and 2AEC:6011.
Udev rule for multi-target Debug board 2AEC:1106
Change-Id: Id7430d0c70647752375230f4024be9f7a2ba95ce
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3980
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The Silicon Labs EM3587 and EM3588 may have 512K of flash.
This fix allows for 512K to be specifiied on the command line
when flashing a device.
Change-Id: I18cc4bd0d14e1f2069066734a7396bcccf3de941
Signed-off-by: Byron Kubert <byronk@google.com>
Reviewed-on: http://openocd.zylin.com/3795
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The need for this due to AICE having 3 interfaces
(EP1 IN-Interrupt, EP2 OUT-Bulk, EP6 IN-Bulk).
Without it, the function will choose first two endpoint as
read_ep/write_ep. This filter will check transfer types
when get endpoint-id. Without this patch, AICE will not
get correct endpoint.
Change-Id: I4da93c7de41cd19e5095b4bfb42078b21f40b678
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/3218
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: Id1959eee5c395666c35f26342c3c50134dd564e5
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3858
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Default values for .first_bank_size_kb and .has_dual_banks fields
described in stm32lx_parts[] do not fully describe
the real device memory layouts.
Basing on:
STM32L0x1 RM0377
STM32L0x2 RM0376
STM32L0x3 RM0367
STM32Lxxxx RM0038
correct values for memory layouts were selected:
id = 0x447 STM32L0xx (Cat.5) <- dual bank flash
for size 192 or 128 KBytes, single bank for 64 KBytes
id = 0x436 STM32L1xx (Cat.4 / Cat.3 - Medium + /
High Density) <- only one size of the bank,
default values are correct
id = 0x437 STM32L1xx (Cat.5 / Cat.6) <- always dual bank,
but size of the bank can be different
For that reason .part_info field in struct stm32lx_flash_bank
is a dynamic field with fields copied from stm32lx_parts[]
and overwriten to correct values
for specific chips and memory sizes.
Change-Id: If638cb0a9916097bfd4eda77d64feaf1ef2d2147
Signed-off-by: Cezary Gapiński <cezary.gapinski@gmail.com>
Reviewed-on: http://openocd.zylin.com/4074
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Fix "couldn't use loader, falling back to page memory writes" error on
stm32l0 which was caused by the use of cortex-m3 instructions in the
flash loader code. The loader is rewritten using cortex-m0 compatible
instructions
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Change-Id: If23027b8e09f74e45129e1f8452a04bb994c424e
Reviewed-on: http://openocd.zylin.com/4036
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
'at91samd chip-erase' command did not work on secured device.
Fix it changing address of DSU.CTRL register
(see Atmel SAM D21 datasheet, 13.9. Intellectual Property Protection).
While on it check error return of DSU.CTRL write.
Change-Id: I83155a634a5458cdc0cc16c99c0e155eb1d8b3d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Thomas Irmen <tirmen@gmx.net>
Reviewed-on: http://openocd.zylin.com/4043
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Adapter clock frequency is set by 32-bit number and most adapters
limit the highest speed safely. There is no reason to impose strict
limit of 5000 kHz if some adapters can do more.
While on it give informative error message in case of zero adapter_khz.
Change-Id: I45c9804678e24496ea769ea9ca6036701b04dde9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3945
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fail if we fail to set debug level. Also, clarify in usage string that
-d<n> doesn't accept spaces.
Change-Id: I9ea9945dc068e3e7cfd18b16ffa2a29366d6e4d1
Signed-off-by: Girts Folkmanis <opensource@girts.me>
Reviewed-on: http://openocd.zylin.com/3880
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds the file ti_beaglebone-base.cfg as the common base
configuration for all TI BeagleBone derived boards. It also modifies
ti_beaglebone.cfg to source the base board and only add the on-board
JTAG adapter. Lastly, it adds a file ti_beaglebone_black.cfg with
a suitable configuraton for the BeagleBone "Black" variant.
Change-Id: I40cacb8abed7bdb308929713891f7b5e5b685c95
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3099
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add new entry in nrf51_known_devices_table for nRF51822 chip found on
chinese Core51822 dev board. The chp has markings N51822 / QFAAH1 / 1630FW
Nordic Semiconductor nRF51 Series Compatibility matrix confirms that this chip
has 256K Flash and 16K RAM.
Change-Id: I571d15913c6f6e02a6f09c883d7dfc5a66b57c28
Signed-off-by: Damyan Mitev <damyan_mitev@mail.bg>
Reviewed-on: http://openocd.zylin.com/4091
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Without the change Atmel EDBG uses default clock freq about 168 kHz
instead adapter_khz configured before interface init.
Changing adapter speed after init works as expected.
Testing shows the EDBG firmware resets speed to default during DAP_SWJ_Sequence.
Tested with fw versions 03.1F.01AE and 02.09.0169
This change repeats the DAP_SWJ_Clock command after sending a SWJ sequence.
Change-Id: Ic70457c5df635f47cad5e70b0dc83a083ea1b3a3
Reported-by: Ladislav Laska <laska@kam.mff.cuni.cz>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3944
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
There is nothing the user can do if their device does not support sector
programming, there is no reason to have this message at warning level.
Change-Id: Ic9b7386e59b64fece7fbfdc543bdfeeed3eae73d
Signed-off-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-on: http://openocd.zylin.com/4105
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Increasing the trace buffer size on the st-link itself gives openocd a greater
chance of avoiding trace data overflowing within the st-link between polls
when there is a large amount of data being sent over the trace port
The st-link appears to split the given buffer size in half
while one half is awaiting transfer over USB, the other half is being
filled by DMA transfer. If you do not poll frequently enough, the DMA
transfer will overflow back to the start of its current buffer, resulting in
corrupted output
Buffer size of 4096 bytes is the maximum allowed by the st-link v2
Change-Id: I169189b021c34f8d18de1601d78b8c5890367d68
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/4085
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The halt event was left pending in the CTI, better to clear it immediately
after debug entry.
Change-Id: I6002f862681baf98769e3c73332a7f7f0ef938c1
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When ARM64 support was being merged, a comparison ended up being
inverted. This causes NULL pointer access when target attempts to
use core cache.
Change-Id: Ic8873ddd13dbdd8100856a71b4717f44cd336e23
Signed-off-by: Girts Folkmanis <opensource@girts.me>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4042
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
configuration covers all 8 Cortex-A53 cores and auxiliary Cortex-M3
used for power management.
Change-Id: I5509f275aa669abe285f9152935ecdcbcd0c402e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4009
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
after handling of an exception in debug state, immediately
restore the original core state.
Change-Id: Ie53b63c9f19815f717f4df4390fbc13f0a204cc2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3996
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
to speed up debugging, don't load the complete register context
on a halt event, load only those registers that might be
clobbered during debugging.
Change-Id: I0b58e97aad6f28aefce4a52e870af61e1ef1a44f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3995
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch contains a major overhaul of the target run control,
mainly for the sake of satisfying gdbs ideas of how a target
should respond to various control requests for the debugger.
The changes allow gdb a slightly better control on how cores
are stepped: a core can be single-stepped while
other cores remain halted or continue normal execution
until the single-stepped core halts again.
Also, on any halting event (user command or breakpoint) the
system is brought into a stable state with all cores halted
before the halt is signaled to the debugger.
This patch also transitions the target code to make use of the
new CTI abstraction instead of accessing CTI registers directly.
Change-Id: I8ddc9abb119e04580d671b57ee12240c3f5070a0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3993
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
- rename "cortex_a" command group to "aarch64"
- remove default blank check, checksum and algorithm hooks
since they're not going to work in aarch64 mode anyway.
Change-Id: Ieb0046786ed9425baf6774c68f42a8285cc2aefd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3991
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Make sure all core register caches are invalidated on reset
assert, make sure to re-init debug registers on deassert.
Change-Id: I82350d04cc3eaae5e35245d13d6c1fb0a8d59807
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3990
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
introduce armv8_set_dbgreg_bits() function to make register
bit-field modifications easier to read.
Change-Id: I6b06f66262587fd301d848c9e0645e8327653de7
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3989
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The aarch32 register cache is only a separate view of the aarch64
registers. Load aarch32 registers through their aarch64 equivalents.
Change-Id: I3e932dfb782f03d73d30d942b24db340a5749e47
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3988
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mmu faults can not be prevented on aarch64, they need to be taken and
handled accordingly. Remove the remaining stub code.
Change-Id: I6241efa594fe6b963624f9628cdf1c8e46588223
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3987
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Not specific to ARMv8, the Cross Trigger Interface
deserves an independent access wrapper.
Change-Id: I84f8faad15ed3515e0fff7f6cc5d1109ef91a869
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3986
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reduce SLOCs in SCTLR retrieval and modification functions and make them
less complex.
Change-Id: Ida1a99c223743247f171b52eef80dc9886802101
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3982
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use the correct opcode for Aarch32 state, both for the breakpoint
instruction itself and the cache handling functions.
Change-Id: I975fa67b1e577b54f5c672a01d516419c6a614b2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3981
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with a Dresden Elektronik deRFmega128 module.
Change-Id: I91da3b11b60e78755360b08453ed368d6d396651
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2790
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
At framework level, the resume hook is not protected. Make sure to
not attempt a resume if the target is not halted.
Change-Id: I4dd1975a95d6c513bd4f4e999e496bc11182a97a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Basically port a fix that was already done for the cortex_a target.
Change-Id: I4cf4519159bda03ed611bc0b2e340a5dad2d85fe
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Instead of supplying a local, preinitialized "dscr" variable, use the
cached value from arm_dpm, which is kept up-to-date anyway.
Change-Id: I06d548d4dc6db68b9d984c83ed026fa9069d7875
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
arm commands are mostly unusable anyway, remove them. to be replaced
by aarch64 specific commands later
Change-Id: Ie994771bc0e86cff1c26f68f1f51ce8ec352a509
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
"currentel" special register is not accessible in debug state.
Change-Id: I9022b01b423cd9ae8227ed018d6166078ba44832
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make debug and error messages more informative, fix spelling and
formatting errors
Change-Id: I7245f42c5153bcc95676270814d30e91c113aaed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
struct arm_reg::value[] must be 8 byte to hold a 64bit register value.
Change-Id: If253e90731d0ee855eafd9d7b63b91f84630cc7c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move clearing of DSCR "Sticky Error" condition to the
exception handling function. Clear once on entering debug state.
Change-Id: Iec1d09d6f2d9cdd7e92953da5ea19f3e399ca12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
recommended for Corte-A8 cores, not sure if necessary
for ARMv8 based cores as well.
Change-Id: Ibcb36170c5fac6a6b132de17f734c70a56919f9b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Remove register cache invalidation and target state changes that are
handled appropriately in other functions.
Change-Id: Ic903f41ddc267f4b8765ea022bd4d6da1017e21f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When a PE is in Aarch32 state and gdb asks for a target description,
provide a register view compatible with the "org.gnu.gdb.arm.core"
feature. Only current-mode registers are exported, banked registers are
not visible.
Change-Id: I99a85d94831cf597fe8cff6a0a1818ce0a33613b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to TTBR in EL0. Circumvent by moving the PE to EL1
before reading, and switch back to original mode afterwards.
Change-Id: I22891b958d3d7e6fad1cb27183c192d975d63d89
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When halting a group of PEs through CTI, HDE must be set in EDSCR for
all of them.
Change-Id: Iaa4bc0b0fe31e46a463c709d8274023225affd85
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When an armv8-a PE causes an exception while halted, e.g. by performing
a prohibited memory or register access, its state is affected in the
same way as if it was running. That means, a number of registers is
overwritten (notably DLR and DSPSR, but also others) and also
potentially the exception level and therefore also the PE state can
change. This state must be restored before resuming normal operation.
This is done by marking the relevant cached registers "dirty" so that
they are written back before resume.
Change-Id: I9b6967a62d7cb23a477a9f7839f8d2b7087eed09
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use proper T32 opcodes for cache identification when the PE is in
Aarch32 state
Change-Id: I9cd9169409889273a3fd61167f388e68d8dde86d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
DCPS only allows to enter higher ELs, for lower ELs you need to
use DRPS. Also, of course the encoding differs between A64 and T32.
Both DCPS and DRPS also clobber DLR and DSPSR, which then need to be
restored on resume.
Change-Id: Ifa3dcfa94212702e57170bd59fd0bb25495fb6fd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
All register access is now performed through common read/write
functions, which delegate the actual register access to the
armv8_common object. armv8_common contains function pointers
to direct read and write requests to the respective low-level
functions for each PE state.
The respective read/write functions are selected on debug state
entry.
At the same time, T32 opcodes are now formatted for ITR in
dpmv8_exec_opcode() and the T32_FMTITR macro is removed from global
visibility.
Change-Id: I9eaef017c7cc9e0c531e693c534901bfdbdb842c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Read registers based on current EL instead of PE mode.
Change-Id: I05d3219ac1bf8585e9f4f024a7e8599fea0913b6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to system control register in EL0. Circumvent by
moving the PE to EL1 before reading, and switch back to original mode
afterwards.
Change-Id: I309f4eea5597ffc88fc892e9bbb826982e8a44ec
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Translate from cpsr value to "enum arm_mode" by shifting up 4 bits and
filling the lowest nibble with 0xF.
Change-Id: Ic32186104b0c29578c4f6f99e04840ab88a0017b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use AT commands to translate virtual to physical addresses based on
current MMU configuration.
Change-Id: I1bbd7d674c435541b617b17022fa9f7f0f01bdab
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set HDE bit through helper function instead of manual mem_ap access.
Change-Id: I68c157870f3f3c47a875d425ade6e975d8075424
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The artificial "os_border" doesn't exist in aarch64 state and is wrong
for aarch32 state as well. Remove it.
Change-Id: I7c673a1404b03aa78dbd505e115fa3a93f7ca05f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Update cache identification to match functionality present in
armv7a_cache.c
Change-Id: I2dc4bee80f5a22b8728334d40331c183d1406f27
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move all DPM related functions from aarch64.c to armv8_dpm.c.
Change-Id: I43404ff5db414ae898787a523d3219e5bee44889
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add database for common, equivalent opcodes for Aarch32 and
Aarch64 execution states
Revisit all functions that access Aarch64 specific registers
or use Aarch64 opcodes and rewrite them to act depending on
current state of the core.
Add core register access functions for Aarch32 state
Add function to determine the core execution state without
reading DSPSR.
Change-Id: I345e9f6d682fb4ba454e4b1d16bb5e1b27570691
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set up CTI so that halt and resume requests get routed to all PEs in the
SMP group.
Change-Id: Ie92cfd3fe54632e5fdc049a6bf5b24b99451a8c9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
For now only D-Cache flush (Clean&Invalidate) and I-Cache
invalidate are implemented. That's enough for software breakpoints.
Change-Id: I8e96d645a230b51e3490403f4564e59ba6a76cf3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
On live hardware, interrupts will happen while the core is
held for stepping. The next step will most of the time execute an
interrupt service instead of the next line of code, which is not
what you expect. Disable interrupts through DSCR before resuming
for a step, and re-enable them again after the step happened.
This should be made configurable, like on cortex_a target.
Change-Id: I94d8ffb58cf7579dedb66bc756b7eb6828b6e8e4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
External debuggers need to use HLT, not BRK. HLT generates a halting
debug event while BRK generates a debug exception for self-hosted
debugging.
Change-Id: I24024b83668107f73a14cc75d951134917269e5c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Don't report breakpoint as debug reason when halt is due to a
single-step event.
Change-Id: Ie6c3ca1e5427c73eb726a038301b6a29a47d1217
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
According to gdb documentation, a register "cpsr" is expected if
aarch64 features are announced. Also, the value buffer must be
capable of holding a 64bit value (8 byte, not 4)
Change-Id: I7aec4e84fa87eadb26797acd0d16c988b9852616
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reduce complexity of memory access functions, anyway there are no ARMv8
platforms that actually contain an AHB-AP at all. while at it, fix
virt-to-phys function signatures to expect target_addr_t.
Change-Id: I55a369686f42993988b6323e5a77f38de12530a9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The step command optionally carries a resume address. In this case,
stepping should start not at the current PC, but at the given address.
Change-Id: Id5792a3745f470cf29efa90c63d65f33d36f6b25
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When armv8_set_core_reg is used to set the value of
the CPSR, also update the internal architecture state.
Change-Id: I5f6a2be6fde8d91ec3352d8ba23c4aa90eb02977
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make DSCR_RUN_MODE() usable for armv8 and arm7 debug
Change-Id: Ib3ba3000d5b6aa03e590f3ca4969e677474eb12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Aarch64 state has different PSTATE and exception level model.
Correct the printout e.g. in poll command.
Change-Id: I1820fd1836c7076ae0aa405fa335fd1a14a2e5b3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Aarch64 has 34 registers, but use ARMV8_LAST_REG instead of
raw integer constant.
Change-Id: I86481899ade74f27fc90eff9f367d444c03e535e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Page table layout in aarch64 is very different from armv7-a layout.
Remove the incorrect handling, to be replaced correct armv8 code in a
later patch
Change-Id: I64c728a72a24f9f4177726ccc07a02a8ca0d56ce
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Not only null control but also value of the breakpoint when it is
removed.
Change-Id: Id99c7e3644729c64e563f1fa8b0577f350be6a98
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
armv8 breakpoint register spacing is 16, not 4 as in armv7-a
Change-Id: I0d49d06878a0c9dab35cde478064e5366f01a8e0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use correct instructions to access CLIDR, CSSELR and CCSIDR.
Change-Id: I319b96c03a44fdb59fcb18a00f816f6af0261f0a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
- armv8 EDSCR has no ITR_EN bit, ITR is always enabled. Writes to this
bit are ignored but we should not do them anyway
- use dpmv8 function to report the reason for debug entry
- WFAR is a 64bit register
Change-Id: I07b81ecf105ceb7c3ae2f764bb408eb973c1d1de
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use opcode definitions from armv8_opcodes.h where appropriate
Change-Id: Iead33fb8e62eb2dd2419ef8932f7d46c087f51a8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The system control register has several instances, depending on the
exception level. Make sure to access always access the correct one.
Change-Id: I9e867f4dbd9625762042f20ed905064ea4e3270f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Flush DTRRX with a dummy read if it's full, clear sticky errors
by writing CSE bit to EDRCR register.
Change-Id: Ia42ae9d3859ba6cbe892d48584e21acdd4e25c84
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use configured CTI base address instead of hardcoded value, if
available.
Use symbolic constants instead of raw hex offsets.
Trim halt and resume code to what is actually necessary.
Change-Id: I4997c2bcca7cebf5ad78859a6a12abe8639594ed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Fix 64bit address setting
Fix register spacing (16 instead of 4)
Set HMC bit for all but linked context match breakpoints,
where the bit is ignored anyway
Change-Id: I48428f39154a6fe5fadc075ca918d1500a0bb241
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Change the signature of aarch64_(read|write)_dcc[_64] to take a
"struct armv8_common *" as the context to operate on. No functional
change.
Change-Id: Ie501113f65ea22aff2eee173ec717f6908a63494
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add or move ARMv8 related dpm function to their own source module
Change-Id: Id93d50be0b8635bd40ddb2a74fe8746ff840d736
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Some vendors don't fully populate the ROM table, e.g. BCM2357 (used in
Raspberry Pi 3) doesn't list CTI, however it is mandatory for halting
an ARMv8 core and therefore it's always present (and required),
regardless of the ROM table listing it or not.
Change-Id: Ia18a4f1b5b931ccd19805b188ebf737c837c6b54
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When using hardware step for doing stepping, the existing DSCR records
the event as external debug request. This will generate a SIGINT event
to GDB and causes it to stop the stepping process.
For aarch64, read DESR to check if the event is a hardware step and set
state to DBG_REASON_SINGLESTEP.
With this patch, GDB can now do source level stepping.
Change-Id: I1d06f819578c74b3ac17376c67f882adddea1f52
Signed-off-by: David Ung <david.ung.42@gmail.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Ensure that we allow halting debug mode after setting breakpoint
Change-Id: I6f0d7a4a4775a93c133fb1ec31dfe3324d9f7395
Signed-off-by: David Ung <david.ung.42@gmail.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add various function to read/write ARMv8 registers.
Change-Id: I16f2829bdd0e87b050a51e414ff675d5c21bcbae
Signed-off-by: David Ung <david.ung.42@gmail.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add new enum ARM_STATE_AARCH64 to the list of possible states.
Change-Id: I3cb2df70f8d5803a63d8374bf3eb75de988e24f8
Signed-off-by: David Ung <david.ung.42@gmail.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Accept 64 bit addresses from GDB read memory packet.
Also allow breakpoint/stepping addresses to take 64bit values.
Change-Id: I9bf7b44affe24839cf30897c55ad17fdd29edf14
Signed-off-by: David Ung <david.ung.42@gmail.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Define a target_addr_t type to support 32-bit and 64-bit addresses at
the same time. Also define matching TARGET_PRI*ADDR format macros as
well as a convenient TARGET_ADDR_FMT.
In targets that are 32-bit (avr32, nds32, arm7/9/11, fm4, xmc1000)
be least invasive by leaving the formatting unchanged apart from the
type;
for generic code adopt TARGET_ADDR_FMT as unified address format.
Don't silently change gdb formatting here, leave that to later.
Add COMMAND_PARSE_ADDRESS() macro to abstract the address type.
Implement it using its own parse_target_addr() function, in the hopes
of catching pointer type mismatches better.
Add '--disable-target64' configure option to revert to previous 32-bit
target address behavior.
Change-Id: I2e91d205862ceb14f94b3e72a7e99ee0373a85d5
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: David Ung <david.ung.42@gmail.com>
[AF: Default to enabling (Paul Fertser), rename macros, simplify]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
This bug was already attempted to fix in an earlier patch but
merging the "defer-examine" feature caused a regression, which this patch
tries to fix again.
Change-Id: Ie1ad1516f0d7f130d44e003d6c29dcc1a02a82ca
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3951
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
