2f8ddc0835
Move the ti targets to a TI folder. Since the folder is ti, we can
drop the "ti" prefix from the files themselves.
Done via the following script:
mkdir target/ti
FILES=`ls target/ti*.cfg target/omap*.cfg target/am335x.cfg
target/amdm37x.cfg target/icepick.cfg target/stellaris.cfg
target/davinci.cfg`
for cname in $FILES
do
bname=`basename $cname`
nname=`echo $bname|sed -e "s/^ti-//g"|sed -e "s/ti_//g"`
npath="target/ti/$nname"
echo "$cname => $npath"
fref=`git grep $cname .|cut -d ':' -f1|sort -u`
sed -i -e "s&$cname&$npath&g" $fref
git mv $cname $npath
done
Change-Id: I9f94dc6bb01f73721d4ff96be92cb51de2cbf0e2
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/9203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
58 lines
1.5 KiB
INI
58 lines
1.5 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#
|
|
# Texas Instruments CC26x0 - ARM Cortex-M3
|
|
#
|
|
# http://www.ti.com
|
|
#
|
|
|
|
source [find target/ti/icepick.cfg]
|
|
source [find target/ti/cjtag.cfg]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME cc26x0
|
|
}
|
|
|
|
#
|
|
# Main DAP
|
|
#
|
|
if { [info exists DAP_TAPID] } {
|
|
set _DAP_TAPID $DAP_TAPID
|
|
} else {
|
|
set _DAP_TAPID 0x4BA00477
|
|
}
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_DAP_TAPID -disable
|
|
jtag configure $_CHIPNAME.cpu -event tap-enable "icepick_c_tapenable $_CHIPNAME.jrc 0"
|
|
|
|
#
|
|
# ICEpick-C (JTAG route controller)
|
|
#
|
|
if { [info exists JRC_TAPID] } {
|
|
set _JRC_TAPID $JRC_TAPID
|
|
} else {
|
|
set _JRC_TAPID 0x0B99A02F
|
|
}
|
|
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID -ignore-version
|
|
jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.cpu"
|
|
# A start sequence is needed to change from 2-pin cJTAG to 4-pin JTAG
|
|
jtag configure $_CHIPNAME.jrc -event post-reset "ti_cjtag_to_4pin_jtag $_CHIPNAME.jrc"
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
|
|
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME cc26xx 0 0 0 0 $_TARGETNAME
|
|
|
|
cortex_m reset_config vectreset
|