b164b65b3b
The datasheets for all STM32C0xx devices report that only SWD is supported. No TDI/TDO pin is present. Drop swj support. Add swd transport. Remove swd transport from the associated board files. Change-Id: If6e630858aa64fbb3938a520604748f3f0ff7356 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/9423 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Ahmed Haoues <ahmed.haoues@st.com> Tested-by: jenkins
75 lines
1.7 KiB
INI
75 lines
1.7 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# script for stm32c0x family
|
|
#
|
|
# stm32c0 devices support SWD transports only.
|
|
#
|
|
transport select swd
|
|
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32c0x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 6kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x1800
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
# SWD IDCODE (single drop, arm)
|
|
set _CPUTAPID 0x0bc11477
|
|
}
|
|
|
|
swd newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
|
|
flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
|
|
|
|
# reasonable default
|
|
adapter speed 2000
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# Enable DBGMCU clock
|
|
# RCC_APB1ENR |= DBGMCUEN
|
|
mmw 0x4002103C 0x08000000 0
|
|
|
|
# Enable debug during low power modes (uses more power)
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
|
|
mmw 0x40015804 0x00000006 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_WDGLS_STOP | DBG_WWDG_STOP
|
|
mmw 0x40015808 0x00001800 0
|
|
}
|