auracaster/sw_openocd
3
0
Fork 0
forked from auracaster/openocd
Code Pull Requests Activity

tcl: Adapt config files to new ftdi command syntax

Browse Source 
The patch was created automatically using the following
script:

%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
ftdi_device_desc ftdi device_desc
ftdi_serial ftdi serial
ftdi_channel ftdi channel
ftdi_layout_init ftdi layout_init
ftdi_layout_signal ftdi layout_signal
ftdi_set_signal ftdi set_signal
ftdi_get_signal ftdi get_signal
ftdi_vid_pid ftdi vid_pid
ftdi_tdo_sample_edge ftdi tdo_sample_edge
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find tcl -type f -name "*.cfg" )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---

Change-Id: Iff781f37bb5511b7e15cbe6dcdf6d28e89fb174f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit is contained in:
Marc Schink
2021-06-23 20:54:49 +02:00
committed by Antonio Borneo
parent 1d4b252bb1
commit 7c38f24529
96 changed files with 494 additions and 494 deletions
Download Patch File Download Diff File Expand all files Collapse all files

20
tcl/interface/ftdi/isodebug.cfg
View File

@@ -2,26 +2,26 @@
# 5 kV isolated JTAG/SWD + UART adapter by Unjo AB
adapter driver ftdi
ftdi_vid_pid 0x22b7 0x150d
ftdi vid_pid 0x22b7 0x150d
ftdi_layout_init 0x0ff8 0xfffb
ftdi layout_init 0x0ff8 0xfffb
ftdi_layout_signal LED -ndata 0x0100
ftdi_layout_signal nTRST -data 0x0200
ftdi_layout_signal nSRST -noe 0x0400
ftdi_layout_signal SWDIO_OE -data 0x0008
ftdi layout_signal LED -ndata 0x0100
ftdi layout_signal nTRST -data 0x0200
ftdi layout_signal nSRST -noe 0x0400
ftdi layout_signal SWDIO_OE -data 0x0008
# Mode signals, either of these needs to be high to drive the JTAG/SWD pins.
# The power-on state is low for both signals but the init setting above sets
# JTAG_EN high.
ftdi_layout_signal SWD_EN -data 0x1000
ftdi_layout_signal JTAG_EN -data 0x0800
ftdi layout_signal SWD_EN -data 0x1000
ftdi layout_signal JTAG_EN -data 0x0800
# In SWD mode, the JTAG_EN signal doubles as SWO_EN_N which switches the
# second FTDI channel UART RxD to the SWO pin instead of the separate RxD
# pin. Note that the default init state has this pin high so when OpenOCD
# starts in SWD mode, SWO is by default disabled. To enable SWO tracing,
# issue the command 'ftdi_set_signal SWO_EN 1' where tracing is configured.
# issue the command 'ftdi set_signal SWO_EN 1' where tracing is configured.
# To switch back to using the separate UART, SWO_EN needs to be disabled
# before exiting OpenOCD, or the adapter replugged.
ftdi_layout_signal SWO_EN -nalias JTAG_EN
ftdi layout_signal SWO_EN -nalias JTAG_EN