The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Part IDs taken from
Atmel-42402C-SAM L22_Datasheet_Complete-01/2016
(revision C)
Change-Id: I1eb76a92097a8327da10faa0551e7fc962a549f8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3426
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Cortex-M0+ and M4 motor control MCUs KV10, KV11, KV30, KV31,
KV42, KV44 and KV46 added to SDID identification.
Watchdog disable code changed to work on Cortex-M0+ (KV1x)
Protection size set to 1K for 16K flash devices (KV10Z16)
- cherry picked from Andrey Smirnov's change #2051
Change-Id: Ia6f4868eaf7e2cb6ad6a736210c703a67e0027be
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3235
Tested-by: jenkins
Reviewed-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
To avoid conflicts between flash drivers being added, consistently use
an alphabetical sort order for the three places new drivers get added:
* Makefile.am NOR_DRIVERS (note: automake disallows a trailing backslash)
* drivers.c struct flash_driver forward declarations
* drivers.c flash_drivers array
Change-Id: Idcd6a8e12821ef10958a6b3ad7bac0dc63cadd08
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3417
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for S6E2DH MainFlash. VFlash is not implemented.
Briefly tested with SK-FM4-176L-S6E2DH V110 board.
Change-Id: If7c523d8c75307bc1494bbf4cca3eed0272e8e01
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3158
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These appear to be just additional flash size configurations.
Entirely based on manual, untested.
Change-Id: I4460dc1a588335df8fc0a385d24513a4e35b6951
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds necessary code to obtain data from the Info region which is
not memory-mapped so can't be read the usual way.
With this "flash read_bank" and "flash verify_bank" commands should
start to work as expected for the Info memory block.
Change-Id: I57e4b80fff577500cfa85954b625fe9c9ff92aa5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3227
Tested-by: jenkins
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Instead of pointing to the assembler sources in a comment and
inline-commenting the THUMB bytecode, place the hex array alongside the
assembler sources and include it via preprocessor.
Originally inspired by a typo in the file path during driver development,
but it also facilitates making changes to the assembler sources.
A Makefile is provided to help automate updating the bytecode. It is not
integrated with the automake system to avoid forcing an ARM cross-compiler
onto every user, i.e. after modifying the sources they need to be rebuilt
in that directory before building the usual way. ARM_CROSS_COMPILE= can
be passed on the make command line to deal with native ARM toolchains
or with varying prefixes of cross-toolchains.
Change-Id: I00ceb980a68c8554a180dd13719ac77b677a8bcd
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3133
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Flash driver for at91sam4 cpu's has been enhanced to recognise and support the SAM4N family.
Change-Id: I50c471a6053b52edffd8efdd8abfe516cc5c55ee
Signed-off-by: Colin Helliwell <colin.helliwell@ln-systems.com>
Reviewed-on: http://openocd.zylin.com/3242
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The flash info command on stellaris platformes
"TI/LMI Stellaris information ... rcc is ..., rcc2 is ..."
presented the actual RCC2 register as rcc and an uninitialized variable
as rcc2 due to a copy and paste error.
Found using the semantic pattern da/da.cocci, see coccinellery.org
Change-Id: I6f920fc3e07fdc085ea8e2248fbc9453eb8393dc
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3368
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A struct member has been initialized twice. Found using the semantic
pattern da/da.cocci, see coccinellery.org
Change-Id: I0320afd60f1ba505758cc5bc0adcf27f572492fb
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Obsolete C source code semicolons were removed using the semantic patch
semicolon/semicolon.cocci, see coccinellery.org
Change-Id: I153b4995a9e028ebaf5f58c947821dc78345a777
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3367
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Writing to Intel CFI flash with unaligned tail bytes raised a false
error message although all data was programmed successfully. e.g.:
> flash write_image image 0x602e0000 bin
> Programming at 0x602e0000, count 0x00000002 bytes remaining
> couldn't write word at base 0x60000000, address 0x602e0000
> error writing to flash at address 0x60000000 at offset 0x002e0000
Root cause for this false error was a mixup of two result variables
introduced with ecc8041c.
Change-Id: Ib6b85293dbed946a36a307e5b198c47b901145bf
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3233
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
FTFx flash controller requires MCU in normal RUN mode.
Flash cannot be erased, programmed or blank checked in VLPR or HSRUN
modes.
VLPR mode is switched to RUN mode as it does not require any changes
in clock generator setting. VLPR can be active from reset on some
KLx devices (with some FOPT setting) so 'reset init' might not be
sufficient to get device to normal RUN.
Any other mode than RUN or VLPR is reported as an error.
Change-Id: I60f494ce0d534b04870c6219d9b05f66f7244433
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3012
Tested-by: jenkins
Command for partitioning FlexNVM to data flash and EEPROM blocks
Change-Id: Ia0ea65d72b0e5f23da330520284b0bd26435e444
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2991
Tested-by: jenkins
FlexRAM should be requested before any section programming.
Test FCNFG RAMRDY bit before issuing FTFx_CMD_SETFLEXRAM
to speed up operation and to cover pflash only devices.
Change-Id: Ib0f2d8e8ab8b1507cbf2b7f8565178ab79941f5d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2990
Tested-by: jenkins
kinetis_ftfx_command() did not use other struct flash_bank* members
than base->target. Switching first parameter to struct target*
enables use of kinetis_ftfx_command() without unnecessary bank
getting and probing.
Removed kinetis_securing_test: kind of dead code, same function
as command flash erase_address pad 0x400 0x10
Removed "NAND" word from help as flash is obviously NOR
Change-Id: I3f5fc295ef2bf42f3e913549949f2a36377f6367
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2988
Tested-by: jenkins
FlexNVM (data flash) is memory mapped at 0x10000000.
Driver used to send the same address to FTFx controller for erase/write ops.
This was wrong as FTFx accepts only low 24 bits of address.
To fix addressing for flash controller kinfo->prog_base was introduced.
Added FlexNVM protection check, blank check and data flash size calculation.
Blank check cannot use block operation on FlexNVM when EEPROM backup is enabled.
Removed non functional reassign logic and bank_ordinal stuff.
Now one can re-probe FlexNVM banks after nvm_partition change.
Change-Id: Ia60b938266963e5d056701278cdf7bf2f62a429a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2987
Tested-by: jenkins
This is for targets where flash controller has reverse endianness
compared to target. For these, the 'bus_swap' parameter can be given to the
CFI driver, which will cause command CFI commands to be written with
bytes swapped. This is only for x16 CFI flash.
Change-Id: I698b768e92e65d160232e90b0e81a824e3c81a46
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3041
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit fd43be0726 introduced a
regression: since the register names were changed from those
traditional for MIPS to common GDB scheme the code that makes use of
them needs to be changed accordingly.
This commit restores pic32mx flash driver functionality.
Change-Id: Id18c739390fae36737a02dc30c363d0444f53b96
Reported-by: Louis Rannou <louson@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3206
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f
Reviewed-on: http://openocd.zylin.com/3171
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Move the mandatory dap_ap_select() call into the dap_queue_ap_read/write
wrapper.
This avoids the need for dap_ap_select() and the notion of a "current" AP
within target code.
Change-Id: I5cde8f3eef2c662f7458be6f3b3dd44ea693bd74
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3164
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All AP operations should select the AP to use before calling it so
there's no point in restoring the previous value afterwards.
The explicit call to dap_ap_select() before all AP operations should be
moved into dap_queue_ap_read/write() which then would have to take the
AP as an argument instead of the DAP.
Change-Id: Icacb0c76ef2a5ac36b4d2f26b52ec01a8850286e
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3156
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All mem_ap_* functions now make sure the SELECT register is updated with
the AP number that it's operating on. This shouldn't have to be handled
explicitly.
Change-Id: Ib193d8930fabb6a25715064355f98258c9580b5d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change the debug_ap and memory_ap fields of the cortex_a target and
the debug_ap field of the cortex_m target to be pointers to the
struct adiv5_ap instead of AP numbers in some known DAP.
This reduces the dependency on the DAP struct in the targets and
enables MEM-AP accesses to take the relevant AP as parameter.
Change-Id: I39d7b134d78000564b7eec5bff464adf0ef89147
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3147
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
They are only used to initialize the flash bank sectors and never modified.
Explicitly specify the array length while at it.
Cleanup before adding XMC4800 support.
Change-Id: I2985b9a9946b67798dbfd47d8b219d93a7ffc3da
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3131
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
