- Move src/target/{interface,target,board,test}/ into src/tcl/
- Remove existing rules in src/Makefile.am and src/target/Makefile.am.
- Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am:
- Add dist-hook to include such files under src/tcl in the distribution.
- Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'.
- Add uninstall-hook to remove the installed script files.
- Change paths to (un)install script files in '$(pkgdatadir)/scripts'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This was forgotten here. All other LPC targets use
this option.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1906 b42882b7-edfa-0310-969c-e2dbd0fdcd60
When the CPU is in the WFI state, the JTAG interface simply doesn't
respond at all and initial tap examination simply fails. Let's simply
do it again when we come around to assert nSRST.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1905 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update two oddball NAND commands to work with {offset, length}
instead of block numbers, matching the other commands as well
as usage in U-Boot and the Linux-MTD utilities.
Document them accordingly. Update the single in-tree use of
those commands (sheevaplug).
ALSO:
(a) Document the current 2 GByte/chip ceiling for NAND chipsize.
(32 bit offset/length values can't represent 4 GBytes.) Maybe
after the upcoming release, the code can switch to 64-bits.
(b) The "nand check_bad_blocks" should report "bad" blocks. They
are not "invalid" blocks; they're "bad" ones.
(c) Tweak the "nand info" command to handle the "no arguments"
case sanely (show everything, instead of showing garbage) and
not listing the blocksize in hex kbytes (duh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1904 b42882b7-edfa-0310-969c-e2dbd0fdcd60
NAND support for DaVinci-family drivers, with HW ECC support.
Declare the NAND chip on the DM355 EVM board.
Currently tested on DM355 for Linux interop using the standard
large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4"
work fine. (Using hwecc4 relies on patches that haven't quite
made it through the Linux-MTD bottlenecks yet.)
Not yet tested: 1-bit on small-page (although it's hard to see
how that could fail); 4-bit on small page (picky layout issues);
the "hwecc_infix" mode (primarily for older boot ROMs; testing
there is blocked on having new bootloader code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Improve support for the DM355 EVM board, and eventually other boards based
on DaVinci chips:
- Provide generic "davinci.cfg" to hold utilities that can be reused by
different chips in this family. Start with PINMUX, PSC, and PLL setup.
- DM355 chip support updates: provide a dictionary with chip-specific
symbols, load those utilities.
- Create a new dm355evm board file, with a reset-init event handler
which uses those utilities to set up PLLs and clocks, configure the
pins, and improve the JTAG speed limit.
Also a minor tweak: provide a virtual address for the work area, matching
what the very latest kernels do. It's probably unwise to use OpenOCD while
the MMU is active though.
The DRAM isn't yet accessible, but NAND access is mostly ready.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1881 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the key command_*() helper functions, fixng the bugs that turned up.
Several of these bugs were from misuse of PRIi64; that's for 64-bit
integers, NOT for "long long" or "u64" (which work best with %lld).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1873 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Bring the mips step/resume interrupt handling inline with the
rest of openocd.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1850 b42882b7-edfa-0310-969c-e2dbd0fdcd60
