Instances of struct flash_driver are never written to at runtime. For a
small amount of memory saving and also robustness (fewer things for
stray pointer writes to hit), mark them const.
Change-Id: Iadbbbc2fac0976d892699200000c5f02856729f3
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4803
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This should allow users to configure flash at >32-bit addresses.
Change-Id: I7c9d3c5762579011a2d9708e5317e5765349845c
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4919
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
read_cmd, qread_cmd, pprog_cmd added as some recent high densities devices
use variants for 4-byte addressing.
Some new flash and FRAM device ids added. FRAMs don't have write pages nor
erase commands or sector sizes. The corresponding entries are marked as
"not used" (i. e. zero). Checks in existing SPI flash drivers added to
handle these cases gracefully.
Change-Id: I5104bce7c815ac22f98bc32c1bb6db66b984404a
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4773
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All drivers which simply allocate one driver_priv memory block
per each bank now use default_flash_free_driver_priv()
Change-Id: I425bf4213c3632f02dbe11ab819c31eda9b2db62
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4417
Tested-by: jenkins
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: http://openocd.zylin.com/3612
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
