This is only minimal support to enable use to catch a Hard Fault in
the stm32l flash bootloader.
Change-Id: I21d6a11893e2f1d173ebff1a651d6f52bf6eec32
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1103
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Other adapters (TI ICDI) that use this driver can use a larger
read/write buffer size than the original stlink could.
Change-Id: I9beb7748049097cbe29a2340799c450bd74e199d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/948
Tested-by: jenkins
Watchpoints were not being enabled when the hl adapter target was resumed.
This effects both stlink and icdi interfaces.
Change-Id: Ia9f8a9415be97a467cd099b63b6bc9f7f37d0c0d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/931
Tested-by: jenkins
As part of the switch to using the hla for the stlink interface we rename
the cmds to a more generic name.
Update scripts to match new names.
Also add handlers for deprecated names.
Change-Id: I6f00743da746e3aa13ce06acfdc93c8049545e07
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/921
Tested-by: jenkins
This enables us to change the target name without breaking any
target scripts.
Change-Id: I635f961e573264d3dab2560f3a803ef1986ccfde
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/919
Tested-by: jenkins
Fix for bug introduced in in mips smp support code
in the resume logic that is checking for wrong return
value.
Change-Id: Ice3e0069f936b556fecc338ccc12ddba38deeaf6
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1048
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If target is disabled at init, then is examined using 'arp_examine', it
can get to cortex_a8_poll with the target state being unknown.
Change-Id: Ifffb345bf971d275d2eb1912648b29f0a75f6ccc
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/954
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This change adds smp debug support for mips platforms. The change
leverages the exiting gdb smp support as mentioned in the OpenOCD
documentation for using gdb in smp environemnt. Added commands
smp_on, smp_off, smp_gdb to control the smp mode. The implementation
also provides a way to send Jc packet and toggle the gdb display core
context as well.
Change-Id: I0835a5aed1844b6ebf8291582912f20695346003
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/937
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a minor change to log EJTAG version 4.x and 5.x
as valid versions when debug log is enabled.
Change-Id: Ie20458d033c6d22842cb4a31b56765d4ba2ff123
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/936
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fixes issue with big endian hosts and mis-aligned data on some hosts.
Fixes unaligned access exception on hosts that do not support unaligned
access when debugging some arm targets.
Signed-off-by: Jason Moehlman <jmoehlma@linux-software.com>
Change-Id: I6bc6fb1b3c3565b256674b9ef43ed2afd14f5178
Reviewed-on: http://openocd.zylin.com/996
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
No function writes to MIPS32_PRACC_PARAM_IN addresses and probably has no much sense.
Any attempt to write to those addresses should be an error.
Change-Id: Iebea5fa9954e2cd56ad34976dd7d25009c6e6388
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/975
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Current code needs 101 pracc accesses for this function, this code needs 12 less.
There is a singularity in this code, is the only function that restore
a register from param out instead from pracc stack. Obviously the register
was previously stored at param out. This save 2 pracc accesses.
Change-Id: Ie95b6f983a3198dafc0eab2dd5acc11f871a8d83
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/958
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
All the the loads are done with lui and ori instructions, there is
no need to save any register, they will be overwritten.
Like in the previous patch, for speed optimization in write code,
same instructions can be saved if the lower half word or the upper
half word is 0.
If the lower half word is 0, it can be loaded with only a lui instruction.
If the higher half word is 0 it can be done with an ori instruction with register 0.
This code saves 10 pracc accesses at a minimum, and 40 at a maximum,
obviously if register 2 to 31 are 0 or a half word is 0
Current code needs 91 pracc accesses.
Change-Id: I892c5b440191d0c7a474c96845d41c373b7fc637
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/957
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
All the writes are done by the new function mips32_pracc_write_mem_generic().
The code is similar to the read generic code.
The reuse of register 15 as memory base address saves 3 pracc accesses.
The first write takes 13(12) pracc accesses and for additional writes 3(2).
Loading miniprograms should take 25% less time and loading fastdata transfer
handler code should be over 2x faster.
Change-Id: Ia3b24ba084af33be99da19f00a7fd4d1b291f350
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/956
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Really nothing new that not explained in previous patches.
The code is expanded as needed, there are no loops in pracc code.
For the first value pracc accesses are reduced from 39 to 16
and for aditional values from 10 to 3.
dump_image should work around 3x faster.
Change-Id: I37c9b13395c09eb52a91f10cdb6cbaedef8ab98b
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/955
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This function is highly optimized, there is not much to
improve.
Loading the base address for pracc access with the new
defined MIPS32_PRACC_BASE_ADDR saves one instruction.
The memory address is loaded in too steps. First the upper
address is loaded. The lower address is passed as an offset in
the memory load instruction.
The offset is signed, if the lower address is in the range of
0x8000 to 0xffff the offset is a negative value, and the upper
address must be incremented by 1.
Pracc accesses are now 12 instead of 14.
Change-Id: I286945b240ed5c5d5cc540780a41a8a5fa075da3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/952
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
MIPS32_PRACC_BASE_ADDR is defined as 0xFF200000. Now is
possible to load the base address with a lui instruction and
only one pracc access.
Offsets to the pracc code addresses are defined to simplify the code
and probably make it a bit more readable or self-explained.
Change-Id: I853dd2d7fad52745931cc6e6be68c0ae156d897e
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/951
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
The function mips_ejtag_read_debug() is defined in mips_ejtag.c
and is called only by mips_m4k_debug_entry() for reading the
CP0 debug register. The comment in this function is obviously wrong.
There is a generic function to read CP0 registers with similar code.
A call to mips32_cp0_read() should work in the same way.
The purpose of reading the debug register is to test if the DSS
bit is set and clear the SSt bit.
It is faster and easier if the SSt bit is cleared without any check.
Remark: DSS bit set only means that a debug single-step exception
ocurred, but it is not possible to step over a sdbbp instruction,
in this case DSS will not be set and the SSt bit not cleared by code.
Resume command at another address will step, so really the behavior
is not the same.
Change-Id: Ibd35f80e0f7669976d96f4ed813830cecf587971
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/950
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code is a bit large compared to mips_ejtag_step_enable().
With the mips32 xori instruction the code can be
reused.
The number of pracc accesses are reduced from 18 to 7.
Change-Id: If3974ebd64da4461c22b089796646990e68e1b72
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/944
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
An issue was observed when using an async algorithm with a target that had
not been previously reset beforehand. The target would enter a infinite
loop within target_run_flash_async_algorithm.
Add a timeout that will at least prevent this issue from happening. and also
suggest the user resets the target.
Change-Id: I5277e0d64e252d3d353e8d5bc9889a37fdc63060
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/949
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The order of the mrc/mcr command matches the ARM Architecture Reference
Manual. This patch corrects the help information for mrc/mcr.
Change-Id: I1f0e6a628a3644124591a6aa291b8a58cfd93b44
Signed-off-by: Karl Kurbjun <kkurbjun@gmail.com>
Reviewed-on: http://openocd.zylin.com/914
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If we halt due to a breakpoint make sure that we do not remove it during a
step, only remove breakpoints we have created.
Change-Id: I060168e54e53637d4fbf3cbcf62072efdb353807
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/947
Tested-by: jenkins
This occurs when stepping past a breakpoint on a even address with
maskisr option set to auto
With -d3 the following log message appears in this case:
"Debug : Interrupt handlers didn't complete within time,
leaving target running"
Cause : Given a breakpoint is set on the lower half word and the PC is on
the upper half word. When another breakpoint is now set on the current PC
then resuming the core will not result in a break on the newly set
breakpoint. This has been observed on a STM32F1x, STM32F2x (CM3) but not
on a STM32F0x (CM0). It's not clear if this is a STM32F1/F2 only or a
general CM3 problem.
Change-Id: I384813f3bfdf935373b5e23cdb2d7f243c70cc00
Signed-off-by: Peter Horn <peter.horn@bluewin.ch>
Reviewed-on: http://openocd.zylin.com/864
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stacking of ChibiOS/RT depends on the usage of an FPU. If the
FPU is enabled the FPU registers are also saved on context switch.
This patch adds automatic detection of FPU for armv7m targets.
Note: With this patch, openocd will only output an error message
warning that the FPU is enabled.
For further FPU support, the correct stacking information
also needs to be added.
Change-Id: I0984cbd9180f247ba2fa610e74a6413cc54239ea
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/961
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
All the packets received will be at start of the packet buffer, so use
more efficient strncmp.
Change-Id: Ib9c45d8f53425367006b1f880c1bde27f03a6cf9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/932
Tested-by: jenkins
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
Seems after a reset the stlink is not clearing the vector catch (VC_CORERESET)
in the Debug Control Register.
This has the side effect if the user presses an external reset the core will
halt, this patch fixes that.
Change-Id: Ic3b2c3991b79cacbbd901c02b79613c2e204e71f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/905
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the target does not support SYSRESETREQ we fall back to using VECTRESET.
This however does not reset the peripherals and we issue a warning to the user
to suggest using a reset-init script.
Also suggest that using hardware srst will give them the same functionality
as using SYSRESETREQ.
Change-Id: Ie1781c4b849fed66c52222e6539735537c879fb3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/802
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Always scan out all bits, but make sure only the allowed number of bytes
end up in the caller-provided buffer. Discard the rest by adding another
scan field when size < 4.
Rewrite the endianness callback to avoid reading outside allocated memory.
Make it directly usable as a callback without the need for a wrapper. Move
the shared callback to a more suitable home in arm7_9_common.
This fixes the regressions introduced in commits
991ed5a2b6cb90d32e38
and
c3074f377c
Change-Id: Ia8bde8c5a9844e89a1d6c0bc8534cd26f02f8d11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The function wait_for_pracc_rw() fails if Pracc bit is 0.
The variable ejtag_ctrl is loaded with the content of the
control register in the first scan.
In the second scan Pracc bit is scanned out as 0, letting
the proccesor go. The result is unpredictable.
All the strange data corruption when scanning at certain
frequencies, or the strange delays needed when entering
or leaving fasdata area are retated to this bug.
Now the code works at any scan frequency, tested up to 15000Khz
and indepently of processor speed, tested at 31.25Khz and 4/8Mhz.
Change-Id: Iedfd81d06d6af4bc738a521f720e42323025b268
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/769
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Check that the target is valid before calling any target functions.
Change-Id: I538fccc79d5ec89976e14beab02cb20490b299bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/766
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Not just print it.
This enables scripts to analyze valuable config options of
arm946e-s cores, do internal BIST memory tests and more.
Be careful to flush caches before disabling it.
Do not forget that BIST test overwrites memory.
- cp15 rewritten from COMMAND_HANDLER to jim_handler.
Change-Id: I734da0be6db0a3127c2daa94ed75efef94da8ceb
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/694
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Cache type register C0.C is read-only, and display
hard core configuration information.
This information is unlikely be changed in runtime.
- removed C0.C access when result is not used in
arm946e_invalidate_dcache()
- access C0.C only once per target, store result
in cp15_cache_info field of target structure
- fix cache index count calculation
Change-Id: I12bc4c967fdf07f54d755f2f2f42406c0ababc1a
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/693
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Global variables 'dc' 'ic' had been used in the code
to keep target's state of D-cache and I-cache
on debug entry.
This may lead to incorrect operation in configurations
with multiple cores and unequal cache states.
Fix: move cache state to the appropriate bits of the
'cp15_control_reg' field (already present but unused).
Vaule of cp15 control register stored here on
arm946e_post_debug_entry(), and analyzed later
in arm946e_write_memory().
Change-Id: I71ef82be00c21d6fffb3726cec4974d1ece70dfe
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/692
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When testing a pic32mx220f032b with different values
for adapter_khz and cpu clocks i was getting a lot of
corrupted data from the chip. From time to time
openocd fails with segmentation faults or is aborted
due to memory corruption.
Change-Id: I134743f75c477b3d55dc74ae4474598e153b4a4a
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/690
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Do not call mips32_cp0_read() if not needed.
This will speed up execution of mips_m4k_write_memory()
by near 2x, with parameter count = 1.
Change-Id: I7829a7802b6475bc6d4ac3f0632d8d239d1072da
Signed-off-by: Salvador <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The ADIv5 spec guarentees that tar_autoincr_block will be 10bits.
Make this the default for Cortex-M family until we detect a Cortex-M3/M4,
we then change autoincrement to 12bits.
Change-Id: Ie8c89134aa036879bdd8a3c312cee9715dbc6913
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/730
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
jim_target_md is supposed to print out results with command_print in
hexdump format. It was using command_print which appends a newline character
aftre every invocation. Using command_print_sameline instead
Change-Id: Iaff03021acc38d54b5a082cb58b82aa4449c0715
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/669
Tested-by: jenkins
Reviewed-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
- Added a few lines of comment before the function explaining the usage and the
output generated by the command
- Added a few lines of comment in the body explaining what is happening to improve
code readability
- Renamed a few variables to improve readability:
* a -> addr
* b -> dwidth
* c -> count
- Added a new variable, named byte to contain the number of bytes to read, instead
of overwriting the count parameter, to avoid confusion between the two values.
Change-Id: I5828ec0f5aadaa39becec7b84f198756bb2c3d41
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/665
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
