The openocd-0.10.0 release

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

NEWS

@@ -3,7 +3,7 @@ source archive release.
 
 JTAG Layer:
 	* New driver for J-Link adapters based on libjaylink
-          (including support for FPGA configuration and EMUCOM)
+          (including support for FPGA configuration, SWO and EMUCOM)
 	* FTDI improvements to work at 30MHz clock
 	* BCM2835 native driver SWD and Raspberry Pi2 support
 	* BCM2835 is set to 4ma drive, slow slew rate
@@ -144,7 +144,7 @@ This release also contains a number of other important functional and
 cosmetic bugfixes. For more details about what has changed since the
 last release, see the git repository history:
 
-http://sourceforge.net/p/openocd/code/ci/v0.10.0-rc1/log/?path=
+http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path=
 
 
 For older NEWS, see the NEWS files associated with each release

configure.ac

@@ -1,5 +1,5 @@
 AC_PREREQ(2.64)
-AC_INIT([openocd], [0.10.0-rc1],
+AC_INIT([openocd], [0.10.0],
   [OpenOCD Mailing List <openocd-devel@lists.sourceforge.net>])
 AC_CONFIG_SRCDIR([src/openocd.c])
 

doc/openocd.texi

@@ -2408,11 +2408,10 @@ This driver is for adapters using the MPSSE (Multi-Protocol Synchronous Serial
 Engine) mode built into many FTDI chips, such as the FT2232, FT4232 and FT232H.
 
 The driver is using libusb-1.0 in asynchronous mode to talk to the FTDI device,
-bypassing intermediate libraries like libftdi of D2XX.
+bypassing intermediate libraries like libftdi or D2XX.
 
-A major improvement of this driver is that support for new FTDI based adapters
+Support for new FTDI based adapters can be added competely through
-can be added competely through configuration files, without the need to patch
+configuration files, without the need to patch and rebuild OpenOCD.
-and rebuild OpenOCD.
 
 The driver uses a signal abstraction to enable Tcl configuration files to
 define outputs for one or several FTDI GPIO. These outputs can then be
@@ -2421,6 +2420,12 @@ are reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
 will be used for their customary purpose. Inputs can be read using the
 @command{ftdi_get_signal} command.
 
+To support SWD, a signal named SWD_EN must be defined. It is set to 1 when the
+SWD protocol is selected. When set, the adapter should route the SWDIO pin to
+the data input. An SWDIO_OE signal, if defined, will be set to 1 or 0 as
+required by the protocol, to tell the adapter to drive the data output onto
+the SWDIO pin or keep the SWDIO pin Hi-Z, respectively.
+
 Depending on the type of buffer attached to the FTDI GPIO, the outputs have to
 be controlled differently. In order to support tristateable signals such as
 nSRST, both a data GPIO and an output-enable GPIO can be specified for each
@@ -2439,9 +2444,8 @@ These interfaces have several commands, used to configure the driver
 before initializing the JTAG scan chain:
 
 @deffn {Config Command} {ftdi_vid_pid} [vid pid]+
-The vendor ID and product ID of the adapter. If not specified, the FTDI
+The vendor ID and product ID of the adapter. Up to eight
-default values are used.
+[@var{vid}, @var{pid}] pairs may be given, e.g.
-Currently, up to eight [@var{vid}, @var{pid}] pairs may be given, e.g.
 @example
 ftdi_vid_pid 0x0403 0xcff8 0x15ba 0x0003
 @end example
@@ -4710,12 +4714,15 @@ and possibly stale information.
 
 @anchor{flashprotect}
 @deffn Command {flash protect} num first last (@option{on}|@option{off})
-Enable (@option{on}) or disable (@option{off}) protection of flash sectors
+Enable (@option{on}) or disable (@option{off}) protection of flash blocks
-in flash bank @var{num}, starting at sector @var{first}
+in flash bank @var{num}, starting at protection block @var{first}
 and continuing up to and including @var{last}.
-Providing a @var{last} sector of @option{last}
+Providing a @var{last} block of @option{last}
 specifies "to the end of the flash bank".
 The @var{num} parameter is a value shown by @command{flash banks}.
+The protection block is usually identical to a flash sector.
+Some devices may utilize a protection block distinct from flash sector.
+See @command{flash info} for a list of protection blocks.
 @end deffn
 
 @deffn Command {flash padded_value} num value

src/flash/nor/core.c

@@ -50,10 +50,17 @@ int flash_driver_erase(struct flash_bank *bank, int first, int last)
 int flash_driver_protect(struct flash_bank *bank, int set, int first, int last)
 {
 	int retval;
+	int num_blocks;
+
+	if (bank->num_prot_blocks)
+		num_blocks = bank->num_prot_blocks;
+	else
+		num_blocks = bank->num_sectors;
+
 
 	/* callers may not supply illegal parameters ... */
-	if (first < 0 || first > last || last >= bank->num_sectors) {
+	if (first < 0 || first > last || last >= num_blocks) {
-		LOG_ERROR("illegal sector range");
+		LOG_ERROR("illegal protection block range");
 		return ERROR_FAIL;
 	}
 
@@ -69,11 +76,11 @@ int flash_driver_protect(struct flash_bank *bank, int set, int first, int last)
 	 * the target could have reset, power cycled, been hot plugged,
 	 * the application could have run, etc.
 	 *
-	 * Drivers only receive valid sector range.
+	 * Drivers only receive valid protection block range.
 	 */
 	retval = bank->driver->protect(bank, set, first, last);
 	if (retval != ERROR_OK)
-		LOG_ERROR("failed setting protection for areas %d to %d", first, last);
+		LOG_ERROR("failed setting protection for blocks %d to %d", first, last);
 
 	return retval;
 }

src/flash/nor/tcl.c

@@ -936,10 +936,11 @@ static const struct command_registration flash_exec_command_handlers[] = {
 		.name = "protect",
 		.handler = handle_flash_protect_command,
 		.mode = COMMAND_EXEC,
-		.usage = "bank_id first_sector [last_sector|'last'] "
+		.usage = "bank_id first_block [last_block|'last'] "
 			"('on'|'off')",
-		.help = "Turn protection on or off for a range of sectors "
+		.help = "Turn protection on or off for a range of protection "
-			"in a given flash bank.",
+			"blocks or sectors in a given flash bank. "
+			"See 'flash info' output for a list of blocks.",
 	},
 	{
 		.name = "padded_value",

src/helper/Makefile.am

@@ -37,7 +37,7 @@ else
 %C%_libhelper_la_SOURCES += %D%/ioutil_stubs.c
 endif
 
-%C%_libhelper_la_CFLAGS =
+%C%_libhelper_la_CFLAGS = $(AM_CFLAGS)
 if IS_MINGW
 # FD_* macros are sloppy with their signs on MinGW32 platform
 %C%_libhelper_la_CFLAGS += -Wno-sign-compare

src/jtag/core.c

@@ -1717,11 +1717,11 @@ void jtag_set_reset_config(enum reset_types type)
 
 int jtag_get_trst(void)
 {
-	return jtag_trst;
+	return jtag_trst == 1;
 }
 int jtag_get_srst(void)
 {
-	return jtag_srst;
+	return jtag_srst == 1;
 }
 
 void jtag_set_nsrst_delay(unsigned delay)

src/jtag/drivers/Makefile.am

@@ -78,6 +78,7 @@ DRIVERFILES += %D%/jtag_vpi.c
 endif
 if USB_BLASTER_DRIVER
 %C%_libocdjtagdrivers_la_LIBADD += %D%/usb_blaster/libocdusbblaster.la
+include %D%/usb_blaster/Makefile.am
 endif
 if AMTJTAGACCEL
 DRIVERFILES += %D%/amt_jtagaccel.c
@@ -171,4 +172,3 @@ DRIVERHEADERS = \
 	%D%/versaloon/versaloon_include.h \
 	%D%/versaloon/versaloon_internal.h
 
-include %D%/usb_blaster/Makefile.am

src/rtos/Makefile.am

@@ -24,7 +24,7 @@ noinst_LTLIBRARIES += %D%/librtos.la
 	%D%/rtos_mqx_stackings.h \
 	%D%/rtos_ucos_iii_stackings.h
 
-%C%_librtos_la_CFLAGS =
+%C%_librtos_la_CFLAGS = $(AM_CFLAGS)
 
 if IS_MINGW
 # FD_* macros are sloppy with their signs on MinGW32 platform

src/server/Makefile.am

@@ -10,7 +10,7 @@ noinst_LTLIBRARIES += %D%/libserver.la
 	%D%/tcl_server.c \
 	%D%/tcl_server.h
 
-%C%_libserver_la_CFLAGS =
+%C%_libserver_la_CFLAGS = $(AM_CFLAGS)
 if IS_MINGW
 # FD_* macros are sloppy with their signs on MinGW32 platform
 %C%_libserver_la_CFLAGS += -Wno-sign-compare

src/target/adi_v5_jtag.c

@@ -574,8 +574,6 @@ static int jtagdp_transaction_endcheck(struct adiv5_dap *dap)
 		if ((ctrlstat & (CDBGPWRUPREQ | CDBGPWRUPACK | CSYSPWRUPREQ | CSYSPWRUPACK)) !=
 						(CDBGPWRUPREQ | CDBGPWRUPACK | CSYSPWRUPREQ | CSYSPWRUPACK)) {
 			LOG_ERROR("Debug regions are unpowered, an unexpected reset might have happened");
-			retval = ERROR_JTAG_DEVICE_ERROR;
-			goto done;
 		}
 
 		if (ctrlstat & SSTICKYERR)
@@ -590,10 +588,7 @@ static int jtagdp_transaction_endcheck(struct adiv5_dap *dap)
 		if (retval != ERROR_OK)
 			goto done;
 
-		if (ctrlstat & SSTICKYERR) {
 		retval = ERROR_JTAG_DEVICE_ERROR;
-			goto done;
-		}
 	}
 
  done:

src/target/arm_dpm.c

@@ -972,11 +972,14 @@ int arm_dpm_setup(struct arm_dpm *dpm)
 	arm->read_core_reg = arm_dpm_read_core_reg;
 	arm->write_core_reg = arm_dpm_write_core_reg;
 
+	/* avoid duplicating the register cache */
+	if (arm->core_cache == NULL) {
 		cache = arm_build_reg_cache(target, arm);
 		if (!cache)
 			return ERROR_FAIL;
 
 		*register_get_last_cache_p(&target->reg_cache) = cache;
+	}
 
 	/* coprocessor access setup */
 	arm->mrc = dpm_mrc;

tcl/target/at91samdXX.cfg

@@ -50,7 +50,8 @@ $_TARGETNAME configure -event reset-deassert-post {
 }
 
 # SRST (wired to RESET_N) resets debug circuitry
-reset_config srst_gates_jtag srst_pulls_trst
+# srst_pulls_trst is not configured here to avoid an error raised in reset halt
+reset_config srst_gates_jtag
 
 # Do not use a reset button with other SWD adapter than Atmel's EDBG.
 # DSU usually locks MCU in reset state until you issue a reset command