107 lines
3.1 KiB
Markdown
107 lines
3.1 KiB
Markdown
# nRF5340 Bluetooth Controller with Support for LE ISO Timesync
|
|
|
|
This fork of the Zephyr HCI UART example adds a custom HCI Command to allow for timesync between the Bluetooth Host
|
|
and the Bluetooth Controller. When the HCI LE Read ISO Clock command is received, the Controller toggles a GPIO and
|
|
returns its current Bluetooth LE ISO Clock in the Command Complete Event.
|
|
|
|
It has been tested on the nRF5340 Audio DK, but it should work with any nRF5340 dev kit.
|
|
|
|
## Requirements
|
|
- nRF Connect SDK v2.8 or newer
|
|
|
|
## HCI LE Read ISO Clock Command
|
|
- OGF: 0x3f, OCF: 0x200
|
|
- Parameters: Flags (1 Octet) unused
|
|
- Response: HCI Command Complete Event with status and 4 bytes timestamp in microseconds
|
|
|
|
|
|
## nRF5340 Development Kit
|
|
|
|
The first Virtual UART (UART1, ...) is Zephyr UART 1
|
|
The second Virtual UART (UART2, ...) is Zephyr UART 0
|
|
|
|
### Pinout
|
|
|
|
Signal direction as seen from the nRF5340.
|
|
|
|
| PIN | Arduino | MCU | Direction |
|
|
|----------|---------|-------|-----------|
|
|
| TX | D0 | P1.00 | out |
|
|
| RX | D1 | P1.01 | in |
|
|
| RTS | D7 | P1.11 | out |
|
|
| CTS | D8 | P1.10 | in |
|
|
| Time Sync| D10 | P1.06 | out |
|
|
|
|
|
|
|
|
### HCI over USB CDC
|
|
|
|
```sh
|
|
west build --pristine -b nrf5340dk/nrf5340/cpuapp -- -DEXTRA_DTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=overlay-usb.conf
|
|
```
|
|
|
|
|
|
### HCI over UART 0 connected to second Virtual UART in J-Link Probe
|
|
```sh
|
|
west build --pristine -b nrf5340dk/nrf5340/cpuapp
|
|
```
|
|
|
|
- HCI over second Virtual port / UART 0
|
|
- Boot banner on Arduino Header UART (P1.01) / UART 1
|
|
|
|
|
|
### HCI over UART 1 connected to first Virtual UART in J-Link Probe as well as Arduino Headers
|
|
```sh
|
|
west build --pristine -b nrf5340dk/nrf5340/cpuapp -- -DEXTRA_DTC_OVERLAY_FILE=uart1.overlay
|
|
```
|
|
|
|
- No Boot Banner on Arduino Header UART
|
|
|
|
|
|
|
|
## nRF5340 Audio DK
|
|
|
|
The first UART (UART1, P1.04, P1.05) is only available via test points (TP60, TP61, ...)
|
|
The second UART (UART2, P1.08, P1.09) is connected to the Arduino headers.
|
|
|
|
### Pinout
|
|
|
|
Signal direction as seen from the nRF5340.
|
|
|
|
| PIN | Arduino | MCU | Direction |
|
|
|----------|---------|-------|-----------|
|
|
| TX | D0 | P1.09 | out |
|
|
| RX | D1 | P1.08 | in |
|
|
| RTS | D7 | P1.11 | out |
|
|
| CTS | D8 | P1.10 | in |
|
|
| Time Sync| D10 | P1.01 | out |
|
|
|
|
|
|
### HCI over USB CDC
|
|
|
|
```sh
|
|
west build --pristine -b nrf5340_audio_dk/nrf5340/cpuapp -- -DEXTRA_DTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=overlay-usb.conf
|
|
```
|
|
|
|
### HCI over UART 0 connected to Virtual UART in J-Link Probe
|
|
|
|
```sh
|
|
west build --pristine -b nrf5340_audio_dk/nrf5340/cpuapp
|
|
```
|
|
|
|
### HCI over UART 1 connected to Virtual UART in J-Link Probe as well as Arduino Headers
|
|
|
|
Release build:
|
|
```sh
|
|
west build --pristine -b nrf5340_audio_dk/nrf5340/cpuapp -- -DEXTRA_DTC_OVERLAY_FILE=uart1.overlay
|
|
```
|
|
|
|
Debug build:
|
|
```sh
|
|
west build --pristine -b nrf5340_audio_dk/nrf5340/cpuapp -- -DEXTRA_DTC_OVERLAY_FILE=uart1.overlay -DOVERLAY_CONFIG=debug.conf
|
|
```
|
|
|
|
To use UART 1 via Arduino headers, the virtual UART of the J-Link probe needs to be disabled, e.g. with the JLink Configuration Tool.
|
|
|
|
|