The coding style requires the 'case' to be at the same indentation
level of its 'switch' statement.
Align the code accordingly.
While there:
- add space around operators;
- remove space after cast.
Skip the file
contrib/firmware/angie/c/src/usb.c
as it's going to be modified by a patch already pending in gerrit.
No changes are reported by
git log -p -w --ignore-blank-lines --patience
Change-Id: I0bebd6d0cc95ddecd5794cc4c12c8412b38691e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/9046
Tested-by: jenkins
To prepare for aligning switch and case statements, fix in advance
some checkpatch error due to existing code:
- uniform braces around if/else statements;
- don't end line with an open parenthesis.
While there:
- move the default case as last in the list.
Change-Id: Idb9603e9a59c7f2e1a7346d5bdd3bde384d2f75f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/9045
Tested-by: jenkins
This adds general support for JTAG adapters based on the WCH CH347T and
CH347F chips.
The CH347T must be configured in mode 3 to provide both UART and JTAG
interfaces. The CH347F exposes UART and JTAG directly. Similar to FTDI
FT2232-based devices, the CH347T/F can be used for simultaneous UART and
JTAG communication.
The ch347 driver code is based on:
https://github.com/WCHSoftGroup/ch347
Bug fixes and adjustments were made to align the code with OpenOCD style
and ensure compatibility. The driver was integrated into the OpenOCD
build system.
The USB packet format was identified using public GitHub sources and
documented here:
https://www.easydevkits.com/wch-ch347-jtag-interface/
Change-Id: I5fca9dd015111e4410fea029611fdeedbb228fdb
Signed-off-by: EasyDevKits <info@easydevkits.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7937
Tested-by: jenkins
Reviewed-by: ZhiYuanNJ <871238103@qq.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Update jtag driver code to reflect these changes and properly drive
Angie probe.
The rationale behind this is to increase the probe performances,
especially in use cases when large files shall be loaded on a target.
The USB transfer performances are now close to those obtained with a
standard FTDI probe.
Change-Id: I3b31d75a3f66c2d07fed8c7423f765acc30925f8
Signed-off-by: Adrien Charruel <acharruel@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8711
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Correct the issue of usb descriptor does not appear
near the PID and VID, Cypress USB controller cannot
handle direct pointers to memory CODE area, so we
copy the data in the external RAM area and point
to it.
Change-Id: I3221627dc8576f6341b444acd9c554fd5cc47918
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8736
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add a check if i2c SDA pin state is HIGH.
if its HIGH, the dev-board is ON, we receive
number of Ack.
in its LOW, the board is OFF, we send this
information back to driver.
Change-Id: Ia40d3910675cc10e0208d8bc0060a19c12b1409d
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8716
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This new code implement two FIFOs for handling TX and RX
JTAG data transfers, its simply receives data and send it
OUT to target chip in respect of JTAG protocol timing
constraints.
The IN FIFO receives data from target chip and send it
back to openocd.
Change-Id: I17c1231e7f4b0a6b510359fe147b609922e0809e
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8715
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We make the proper GPIF configurations for OUT/IN transfers
which are : the GPIF state machines for each direction OUT/IN
We change the Vendor-commands to handle GPIF config before
triggering it.
Change-Id: I2f3bd7bed1a378536bf017336b5031683d93e3c1
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8713
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new firmware of ANGIE will not use Bitbang method to
transfer jtag data to the target chip. instead, it will use the
the GPIF module to bypass JTAG data directly to the FPGA and
then to target chip.
So we delete the protocol and jtag files which handle bitbang.
We are going to use endpoint 2/4 for OUT/IN GPIF transactions,
and we deactivate the endpoints 1IN and 1OUT.
we will keep the endpoint 6/8 for i2c unchanged.
Change-Id: I0fcb23690526f6a7da044b702217b32522be727a
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8712
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When attempting to write to internal flash the flashing step fails with
'Error: timeout waiting for algorithm, a target reset is recommended'.
Updated flashing algorithm for MAX32xxx to fix this.
Change-Id: I51350c1320c9699ddcf6cb28d9299538bece4c4f
Signed-off-by: Henrik Mau <henrik.mau@analog.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8794
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Driver for DesignWare SPI controller, found on many SoCs (see compatible
list in Linux device tree bindings
Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml). This
implementation only supports MIPS as it was the only one available for the
tests, however, adding support for other architectures should require only
few adjustments. Driver relies on flash/nor/spi.h to find Flash chip info.
Driver internal functions support 24bit addressing mode, but due to
limitations of flash/nor/spi.h, it is not used. The reported writing speed
is about 60kb/s.
Lint, sanitizer and valgrind reported warnings were not related to the
driver.
Change-Id: Id3df5626ab88055f034f74f274823051dedefeb1
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8400
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro named LIST_HEAD() clashed with a macro of same name in
the GNU libc file sys/queue.h.
This causes a warning in MacOS build due to some other system file
including sys/queue.h.
Rename LIST_HEAD() as OOCD_LIST_HEAD().
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: Ic653edec77425a58251d64f56c9f5f6c645ba0cd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Andrew Shelley <ashelley@btinternet.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8683
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andy <andrewjohnshelley@gmail.com>
This updates the flash driver to support more than one bank.
This is required to support the cc1352p7 which has two banks.
This only have been tested on a cc1352p7.
The loader has been built using a gcc-arm-none-eabi-4_8-2014q3
toolchain.
Change-Id: Ia813421ececd96d6e2fd4dae910ad60fcc3d3c88
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8192
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added FT4232HA varianet of FTDI's FT4232H which has a different bcd.
Also added default PID/VID for the FT4243HA to contrib/60-openocd.rules.
And added default PID/VIDs for FTDI's HP ICs to contrib/60-openocd.rules
as this wasn't done previously.
BugLink: https://sourceforge.net/p/openocd/tickets/410/
Change-Id: Ia84b566aa004332d3f7815a3d22ac37eee4f522a
Signed-off-by: Jonathan Forrest <jonyscathe@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This document is outdated and has broken text formatting. It also
provides no useful information to users nor developers, at worst it
causes confusion. For that reason, drop this file.
Change-Id: Id5ee1f6e74d1a641c60d897f114bb97f5fd48e5b
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8292
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This file is intended to be included in any user's project that
plans to use OpenOCD awareness for uCOS-III.
It is supposed to be distributed under a license compatible with
the uCOS-III code, that is Apache-2.0 license.
Distribute it under Apache License 2.0.
Change-Id: I51ecd469c8ccdd23a069d21e89b7d90886691395
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7996
Tested-by: jenkins
Before this change, when we send an I2C Bulk data at the same
time while Jtag bitbanging functions execute, the microcontroller
puts JTAG bitbanging on wait and executes all I2C bitbanging
function, which causes problems like loss of Ack in DAP responses
and other errors.
With this commit, When I2C interruption occurs, it sets a variable
to true and continues JTAG bitbanging, when it finish it executes
the I2C bitbang.
Change-Id: Ia80bac21f8a259f4a1176b5346bf74ed0aa6e38b
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8074
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add GPIO extender initial configuration that is needed to configure
some important GPIOs and ensure that the dev board is ready to work.
Add i2c_write function that make a write transfer to any slave device.
Give a new Product ID to ANGIE to make it different than the non
programmed ANGIE.
Change-Id: I0a8dacb7fe218145b7d3ed1cb75f106ed6256714
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8072
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We want to keep the tri-state buffers located between the FPGA
and the board, in 'Z' state until we launch an i2c connection.
We launch an i2c start condition, make the SCL
direction 'OUT' to start the i2c protocol and at the end
of the i2c connection at the stop condition, we re-make
the tri-state buffers at 'Z' state.
Change-Id: Ic597a70d0427832547f6b539864c24ce20a18c64
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7989
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change the GPIF state machine, configuring only one of the 4 waveforms
to generate the clock signal (CCLK) used to program the FPGA, and send
one byte every cycle using an 8-bit bus.
Change-Id: I43cf5480b9d5c40cc2f6a62a52ecfe078b76458e
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7976
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This file is intended to be included in any user's project that
plans to use OpenOCD awareness for FreeRTOS.
It is supposed to be distributed under a permissive license to not
impact the original license of the user's project.
Distribute it under Creative Commons Zero v1.0 Universal license.
Change-Id: I7ac90e8b742517bcafc08c00662625671c8159c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7995
Reviewed-by: Karl Palsson <karlp@tweak.au>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
add new i2c bit-banging feature, we can now connect in JTAG with the SoC
target and in i2c with the main board components at the same time.
Change-Id: I8e4516fe1ad5238e0373444f1c3c9bc0814d0f52
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7796
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
add a line that checks the returned value of set signals function
add two VIDs of other original boards (have onboard angie architecture)
so angie driver can connect to them and change their VID after
renumeration.
Change-Id: Ide4f1f6f38168a410191bf3ff75bcd59dcf7ef50
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7795
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This is ANGIE's firmware and bitstream code.
The 'Embeded C' code is based on the openULINK project.
The hdl bitstream source code is for the spartan-6 FPGA included in
ANGIE.
Since ANGIE has a different microcontroller (EZ-USB FX2) than openULINK
(EZ-USB AN2131), the registers file (reg_ezusb.h) has been changed
completely, so are the descriptors, interruptions and the endpoints
configuration.
Change-Id: I70590c7c58bac6f1939c5ffba57e87d86850664d
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7701
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simply move numicro M0 flash write assembly to contrib/loaders. Also,
modify corresponding Makefile and generated numicro_m0.inc.
To make the path more general, this patch rename the path
"contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as
well.
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26
Reviewed-on: https://review.openocd.org/c/openocd/+/7346
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I24bd362eeb6b74f09aceb9b757d45cbfa4afe334
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7160
Tested-by: jenkins
Replace the GPLv2-or-later boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I380d552940f1c405309a3346454251c0e80b5a45
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7159
Tested-by: jenkins
